Explorer :: 2001 Ford - RPMs Drop To About 4 To 500 And It Stalls Out In Reverse Only
Nov 27, 2011
I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 Replies
Advertisement
06 Elantra Limited, 96,xxx miles. When I'm idling at a light or something, the Rpms drop for a split second, almost to the point of stalling, but recovers. Happens in a split second. Does the same thing even when driving, but does it more frequently when idling. It even does that when I first put my foot on the throttle to accelerate from a red light.
I've cleaned the throttle body but it still does it. I've taken it to 3auto parts stores. One said that battery was bad. The other said the battery is fine but alternator is producing low. The last said both are fine.
View 11 Replies
2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.
View 6 Replies
Just finished putting a fresh 460 backed by a (1977) c6 in my '68 ranger and now I'm having (what I believe is) transmission problems. The truck will idle and rev properly in gear but as soon as I put it in drive or reverse the RPM's drop and it dies. I jacked the back end up and put it in both drive and reverse and the tire's spin, but if I try and apply the brake to stop them the truck will die. My suspicion is that the torque converter is locked up all the time. I have managed to get it in gear and give it gas and it'll drive and shift fine, until I come to a stop. My question, what would cause the converter to do this? It's the same transmission and converter that I pulled out a month ago and I never had any issues before...
View 4 Replies
1st problem is shifting from 1st to 2nd and sometimes from 2nd to 3rd though, 2nd to 3rd is not as bad as from 1st to 2nd. It stumbles and gets really bad if I don't let up on the gas. After the initial shudder it will go into 2nd just fine. I also have to gun the gas a little bit when I first start the car, or it will just sit there and idle and never go into gear.
2nd and more annoying is that it stalls after driving around a bit. It happens on freeway or city. It doesn't stutter or anything the rpm's drop to 0 and it just stalls and won't start up for a 5 - 10 minutes or so.
Codes pulled are P0731, & P0736. The transmission was replaced about 2 years ago with a refurbished one. Could it be going out again already? The guy at Autozone suggested replacing the TSS (Transmission Speed Sensor?) to see if that was the problem. I have not done this yet, but plan to.
View 3 Replies
I have a 2003 Camry 3.0l v6. Stalls at lights random.
Currently the car stalls at stops but this doesn't happen all the time it can go a month in between the problem occurring its very random. While sitting at a light the rpms drop and then it revs up and cycles like that for quite a while. This will also occur while cruising at a low speed while I'm just coasting the rpms will go up and down. I can compensate while stopped by power braking and keeping it at its normal idling rpm. I have no check engine lights and can't seem to determine what would be causing this issue.
View 5 Replies
I purchased a 92 Lumina Euro with a 3.1 and 101,400 miles on it a little over two weeks ago. It has been having problems since I got it.
It stalls intermittently, typically after I drive to work, shut it off for two hours, and then start it to go to my next client(home health aid) sometimes it stalls right after starting it then, and/or sometimes when put in reverse and/or drive and occasionally at stops signs after the aforementioned problems occur. It has also stalled out twice after highway driving after the car is shut off and started shortly afterwards, for instance, when I ran into a tobacco store for some cigs.. After the problem occurs it usually drives ok if I continue to drive it awhile even if I shut it off for a short time and restart.. I added some fuel injector cleaner when I filled the tank but it didn't work.
After about a week of the stalling issues the car refused to start after dying and didn't start for two or three days. As I was unable to get an answer from the dealer my step-father, who went with me when I bought the car, called him and he said if I could get the car there he would fix it. So I borrowed a bundle to have it towed the 25 miles or so to the small town car lot.
His mechanic supposedly fixed it by replacing the TPS and the dealer informed me that they had cleaned the throttle body before I bought it and apparently the TPS needed replaced to. However the issues again started after one day of it running fine. I tired to get a hold of this guy again and again I get the voice mail and no return call so as soon as I got off work I drove it over there and again he said he would fix it. He had it for three days and I again tried to get a hold of him without success and he again answered the phone for my step-dad and told him they had ordered some kind of module that would be in Monday. So Wednesday he calls me and tells me that they didn't replace this module because when they took it out it tested good five times but they noticed some gunk build up at the contacts of the wires that hook to the module and now the car was fixed. Why did they order the part before testing??? This doesn't make sense so it throws doubt on what the man said. I went to get the car and when I got back to my town and went to get those cigs it died twice after restart and put into reverse. That was two days ago and it has been dying once or twice each day since then although it is somewhat better than before as it isn't taking as long for the idle to even out at sufficient rpms after I throttle it at idle or drive awhile. BUT now it seems to be sucking the gas hard and I am wondering if this guy just did some jerry-rigging because he sure isn't fixing it.
A few more details. The rpms drop rapidly when this occurs, it has a couple of times had a rough idle at the same time but more often the rpms drop and it dies.Sometimes if I use the throttle and keep it up around 1000 rpms for a short time it won't die. I have smelt a burnt smell a couple times when I shut the car off, like electric burnt, not oil burnt or stinky exhaust. Lets see, I felt a very brief loss of power feeling when driving on the highway on two different occasions, so brief that it was barely discernable. It runs over the halfway point on the temp gauge after driving awhile in town, seems a little hot to me but I read these cars don't kick on the fan till 220. Sometimes the rpm bobs a little up and down at idle and slow speeds and once the battery power dropped and popped right back up when it was idling funny and when it had that no start an acquaintance tested it by putting a screwdriver in a plug wire and pointing it towards the engine as I cranked it and he said it had no spark and it did crank every time I tried to start it during the no-start condition. It has also done a bit of surging from time to time when the prob happens. The car is recovering from the stall condition quicker than it did before since this last "fix" but still stalling.
View 5 Replies
I have a 1983 Honda Accord (manual with nearly 200,000 miles) when rolling to a stop or at a stop rpms drop below 1000 and it stalls out. I can start it back up without hesitation.No hesitation at initial startup or after sitting short or long time, it idles while in park rpms about 1000.When I feel the engine about to stall while rolling to a stop or at stop, if I put my left foot on the brake pedal, slightly step on the gas pedal with my right foot it prevents the engine from stalling. At stop if I put in park, rpms raise and don’t need to give it gas.
I'm unable [& unqualified] to work on my car. Given I drive only about 1,000 mi year; my alternate form of transportation is a bus or kindness of friends, I’m on a limited income, cannot afford to buy/ spend more than 2,000 -- my question if 2-foId, 1. is it possible that something it is nothing major and worth repairing/replacing (ex. air control/idle air bypass valve, a dirty throttle body or even carburetor)?2. Or, as discussed with one mechanic, since the car is 33 years old, during or soon after repair other problems (dried out vacuum hoses or major) will follow. Plus, parts can be difficult if not impossible to replace as a I spoke to mechanic pointed out.Given the car’s age is it worth repairing?
View 5 Replies
I think it's possessed! My sisters vehicle, a 2002 Explorer with a 4.0 V-6, automatic, 2 wheel drive will just shut off. At first it acted like it would vapor lock. But it would start right away. then the a while later, (several months), it got where it would drop rpms and the engine shudders, sometimes not dying.
When this first started, the throttle body was cleaned, a new air filter installed, fuel pressure checked. Everything checked out and for a few days it ran fine. Then it started all over again. There has never been a code thrown. All of this goes on only when the ambient temp is above 70 deg.'s. below 70 deg.'s it runs perfect.
Last week it went to the mechanic again and a new crank speed sensor, fuel pump, and diagnostic done. He could not find anything wrong any where. Took it for a test drive and it dyed on the mechanic. Still no codes. What the problem might be? Every Mechanic that has looked at it has gave up, one even saying, " it's possessed."
View 14 Replies
Hot or cold car always starts,Idles perfect , then RPM drops, Idles rough and stalls. Econometer moves to Red area.car will easily restart and drives well,it also idles well. Once engine is shut down, even for a short while, It does the same thing again. Car is used for short trips. Ambient Temperature 80 degrees. Once running car is perfect at all speeds and idles smoothly. Hero 1987 MB 560 sel ....
View 19 Replies
95 explorer 4.0l ohv. I go to take off and then come to a stop after about 10-15 feet, i just give it a little gas then lightly press the brake, rpm's drop to around 400-500 then back to normal. I have replaced:
IAC
MAF
Plugs & wires
Coil pack
intake manifold gaskets
fuel system cleaner
fuel filter
air filter
View 3 Replies
the wife's '01 Excursion has developed a new idling quirk. While sitting, it will briefly drop rpm's. You can hear it, and see it on the tach gauge. No other noises or problems, except for the brief drop in rpm's.
View 3 Replies
I ran out and test drove a new to me 2001 F350 7.3L tonight. Everything seemed good, until I got back from the test drive. I pulled in and was sitting there with it idling. It seemed to idle fine, then a very small miss and very small shimmy then idle fine again; then another small miss and another shimmy. It continued like clockwork. Every time it seemed to miss and shimmy, the RPM would drop just a little, but not much. Does an ICP sensor sound like the problem, or maybe something more serious? 2001 F350 7.3L with 235,733 miles new trans, turbo replaced at 150,000 something miles. No blow by. Idled fine before driving, also drove fine. It doesn't seem to surge when idling, just kind stalls and shimmys for a split second then idles fine for a few seconds.
View 1 Replies
Can't run a/c rpms drop to almost 200 from 1200-1500rpms. Really bad when at at traffic light. I have to constantly press gas pedal.
View 5 Replies
I have an 01 Buick Regal GS, 82k miles. When I baught the car it had 80k miles but had been sitting for a while. I put in a new battery and changed the oil as soon as I got it. When accelerating the RPMs will go up but the car won't accelerate as fast. The RPMs will drop and the car will jerk forward. And then accelerate better after it is warmed up a bit. I thought to give it some time and maybe it will go away. 2k miles later it is still doing it. What it could be?? I would like to see if I can fix it myself.
View 3 Replies
I had my Honda Odyssey transmission replaced 2 years ago. The past few months, in the first mile that I drive the car on streets in our neighborhood, the car goes into high RPMs (about 3000) before it seems to drop into gear. It does this 2 or 3 times then works fine after that. The "Check engine" light is now on all the time. Sometimes, the car does one other weird thing--the high RPMs end with the drive/D4 light flashing on and off like a blinker (even if I change gears to D3. When this happens, if I turn the ignition off it comes back on and seems to function fine. I have had it back to the shop that did the work about 4-5 times to get it right. I like the guys but each time they return it to me, the problem remains. I took a 2000 mile trip with it and with the exception of this persistent problem, the van worked fine.
View 2 Replies
I gave my daughter the '01 sport trac as her first car... just had to do: fan and clutch, ps pump, ac compressor pulleys, a/c line, actuator...
Now the reverse lights have gone out. Bulbs and sockets appear just fine... did notice shift indicator on dash is off just a bit... it reverses just fine....
Is there a linkage adjustment or some switch that is bad?
View 4 Replies
I have a 2001 Hyundai Santa Fe LX with 214,000 miles on it. In general, I am having two problems which are most likely related. I would like to get opinions on what is causing the problems, how to fix the problems, and what the cost might be for the fix. This is an older car and I don't want to bring it to a mechanic to just do searching.
1. RPMs fluctuate quickly at slower speeds in town stop and go traffic and while parking in Drive or Reverse. Fluctuation can be between 1000 to 2000 and 3000 RPMs back and forth.
2. Car stalls while sitting at stops when in Drive. When car stalls, RPMs have suddenly decreased to 0 (zero).
3. RPMs fluctuating and car stalling typically occur after I have made my first stop and have turned off the car.
There is also a Check Engine Light Code: P0304, Cylinder 4 Misfire Detected. I changed the vehicle speed sensor a few months ago.
Here are the details of what has been happening, when it happens, and what I have tried.
- When RPMs fluctuate, the car slowly accelerates and slows down and I can hear revving high and low. This happens when the RPMS fluctuate just a few RPMs around 1000 and when the RPMs are fluctuating up to higher RPMs.
- After the car has been driven for about 45 minutes and car is at slower speeds, RPMs will fall to zero while at stop and in Drive, and the RPM fluctuation will begin.
- RPMs jump to 2000 or 3000 and stay there but do not fluctuate when car is put in Park and Neutral.
- When car is in Park and at 2000 or 3000 RPMs, car takes a few extra seconds to turn off.
- Car accelerates without pressing gas pedal and will accelerate up to 40 mph.
- Car will sometimes lurch at slower speeds of 15, 25, and 35 mph when RPMs are fluctuating or when the gas pedal is pressed.
- When RPMs are fluctuating and at 1000 or higher and I am pressing the brake to slow down, the car fights in Drive and in Reverse.
- RPM fluctuation does not occur at interstate speeds.
- A couple days ago, when I was at interstate speeds of 60 to 75 mph and pressed the gas pedal, the car would stutter and jerk.
- RPM fluctuation and stalling primarily do not occur when the car is started at the beginning of the day or when the car has been off for several hours.
- Twice In the last week the RPM fluctuation and stalling occurred even after car was not started for several hours and after only about 5 to 10 minutes of driving in town stop and go traffic.
- Sometimes car stalls when I'm at a stop and slightly press the gas pedal to start driving.
- There are times in town traffic when the car is operating normally and is at 750 RPMs at stop, then the RPMs suddenly decreased from 750 to 0 (zero) and the car stalls.
- From Neutral, sometimes when I simultaneously put the car in Drive and press the gas pedal either by feathering or forcefully pressing pedal 3/4 to the floor, the car would have a delayed reaction to accelerate but would not shut off.
- After car has stalled, if I try to start it right away, the car cranks but does not start for about 5 minutes.
- The time between stalling and being able to get the car to turn back on has increased over time from starting up at first crank to not starting for 5 minutes.
- If I let the car sit for 3 to 5 minutes after it has stalled, the car starts up but takes a couple seconds to start while pumping the gas pedal.
- Issues have been happening since November but are getting more frequent.
- Stalling is happening more frequently and within minutes of each other.
View 10 Replies
Have a 2001 CRV that is running really bad. It almost stalls when I put it in gear or even when the RPM's fall to idle. It is now throwing a p0172 code. I have a simple scan tool and verified the MAP reading and primary O2 voltages as suggested by the manual, both appeared to be normal. It seems all the symptoms point to valve clearance, however the valve were adjusted not 2000 miles ago by the dealer during the 150K service, and this issue has existed before and after that adjustment. I also cleaned the IAC screen with no changes.
View 5 Replies
I have 2001 ford explorer sport.. it idles very low in drive and reverse and then shuts off.. What has been replaced:
1. Torque converter
2. All new plugs n wires
3. Map or mass sensor
4. Iac valve
5. O2 sensors
6. Fuel filter
7. Air filter
8. Throttle valve/sensor
It does not run bad only when u come to a red or stop light.. Had the vacuum tested and no vacuum leaks.. also no check engine light has come on and no codes have popped up when tested..
View 1 Replies
Was going to leave the other morning and put it into reverse and nothing happened. Tried every other gear and works fine. Reverse is the only thing giving me problems right now. Tried doing some research on my own, because I can't afford a tranny rebuild. I was hoping it was either the solenoid or low/reverse band. I don't know about the band, because it works fine in low2 and low1....
View 2 Replies
