OK. I'm getting a P301 code on the OBD in my 2000 Expedition (5.4 L). Already replaced plugs x 8, coils x 8, & fuel injectors. Still have rough idle when it starts up, usually for a few minutes & then it's mostly OK. Maybe a small rumble now & then when @ a red light, etc. Replacing fuel filter & all 4 o2 sensors tomorrow.
View 9 RepliesHaving trouble with my '00 Jetta 2.0 A/T w/ 98K miles. Had the water pump replaced @ a year ago (for the 2nd time, the 1st replacement died after <15K miles.) The car has had issues with rough idle when started, especially with a cold engine, since before the 2nd water pump. I've replaced the coil pack, thermostat, and coolant temperature sensor in the recent past in addition to the water pump & timing belt.
The gas mileage sucks, and when it's idling rough it doesn't "idle up", & will stall if the gas pedal is pressed with 30 secs. of starting. Otherwise it seems to run fine. The coolant temp. sensor was replaced after a CEL indicating it was bad. The CEL went off after it was replaced, but it's now throwing a P1296 Cooling System Malfunction. I have noticed the temperature gauge fluctuates instead of staying around the "middle" since the 2nd water pump replacement, and will run "colder" in colder weather. Since spring is here, the temp. gauge stays around "normal", or the middle.
Some research online says thermostat OR coolant temperature sensor. Since the gauge registers normal now, I'm leaning towards a bad temp. sensor...?
Does the hard start/rough idle and the cooling system malfunction CEL could be related?
I have a 2000 jetta 2.0, and the idle seems to rough and when I start the car it seems like I might stall.
View 9 RepliesI recently bought a 00 Excursion v10 2wd everything looked right no major problems. I noticed it has a rough idle and i thought it could be the EGR i went under the hood and there's no EGR in sight. I plugged the OBD reader to see if it would give any codes since the there was no check engine light on and wanted wanted to make sure it worked, It showed a P0304 code its Cyl4 misfire i checked plugs/coils and i noticed there's a little insert inside Cyl4 plugs hole in the head that it has the plug screwed on. I decided to change all the plugs and the coils and i still have the rough idle and code i can hear a ticking noise around the engine in the passenger side.
View 7 Replies2000 Sierra 1500, 5.3L engine. When he starts it in the cold (below 40 degrees) at first hits 1000rpm, then immediately drops to 400-500rpm. The idle is rough and wants to die if he tries to drive it. However after 10-15 minutes and the eng warms up, its fine no problems at all. There is no codes, so the scanner we had didn't tell us anything. He had cleaned the TB and intake system with cleaner, no dice. He also disconnected the IAC while it was idling rough, that didn't change the way it ran at all. We would like to toubleshoot it more before we start throwing parts at it.
View 1 RepliesSymptoms:
- Check engine light: misfire on all cylinders, and "lean fuel trim at part throttle".
Started with changing leads and plugs without improvement. Then I found the tank ventilation seemed to be clogged, as there was a massive vacuum when opening the filler cap. Checked the canister and replaced a couple of corroded lines. Also used compressed air to blow through the canister and lines up to the Evap-purge valve. Seemed to be OK afterwards (no vacuum), but still misfires.
Changed the Mass Air flow sensor, and it seems the misfires got better, but instead I have some other issues:
- Hard to start when cold. Starts up fine for a second then sounds like it's getting to much fuel and dies. Possible to keep it running if pumping the pedal or holding it at higher revs.
- Rough idle when warm. (Same as before I changed the MAF and plugs/ leads.)
- Drives and runs ok when out on the road.
- Pulled the cable to the Idle Control Valve without any change in idle...?
- Got flashing engine light and "misfire cylinder 4" when giving full throttle on low revs and seond gear up a steep climb.
What could cause this?
- Temperature sensor?
- O2-sensor?
- Idle control valve?
- Coilpack?
Having a real headache with my Expedition. After doing short journey's will park up the car, come back and it won't start. The dashboard lights are on everything seems ok but the engine won't even turnover. Leave it for about 45mins+, it stars immediately. The mornings are no problem at all it starts first turn.
It is now going into the Ford Dealers for the 3rd time, 1st they cut me new keys was fine for 5days problem returned, 2nd they replaced a new ground cable was great for 22days then same old problem returned. They ran a diagnostic test and everything was working fine.
My 2004 Rubicon has been having some idling issues. It idles kind of rough (+- 200 RPM) and is hard to start. I tried to start it recently and after 4 cranks, it started then the CEL came on, and has been on ever since. I have recently moved from Washington state to Houston Texas, and the problem starterd here in Texas. I checked the code and am getting a P0505 code. I had a mechanic replace the IAC valve, Checked for vacuum leaks, and cleaned the throttle body. The mechanic says the output from the main computer appears to have burned out, and needs to replace the main computer(for $1000). The mechanic can clear the CEL, but after turning the jeep off then back on it reappears. The mechanic says he verified the computer was the problem by installing a known good computer and it cleared the problem. Does this sound right to you? If my computer is bad, wouldn't my whole operation be affected?
View 4 Replies1997 lexus ls400 204500 miles, engine light is on code P0340 (cam shaft position sensor bank 1), rough idle at start, once the car warms up it runs ok but loss of power, hesitates, if press more on gas pedal the car jerks. I have replaced both cam shaft position sensors and engine coolant temp sensor but no improvement. What could be the problem?
View 15 RepliesMy '05 Excursion recently started having rough idle and some loping when started cold. It seems to run good and idles pretty good when it warms up. I'm also getting a P0488 code (EGR Throttle Control Circuit A Range/Performance). I do have a BPD EGR and I don't recall if that would throw a code alone? I'm taking a trip next week and want to get it straightened out. Does it sound like an EGR valve issue?
I also thought about a battery issue, I know that can cause weird problems. I have Duralast batteries and they always seem to fail at about 2-3 years. I took it in and they say it tested good but I'm not always sure with them. Long story, but when cranking for longer than normal, the cranking power would drop quite a bit. Checked battery and had some corrosion. Cleaned and upon further inspection, the positive post is a bit eroded at the base and sunken in. The voltage was about 12.35 after sitting all night, a couple of the cells were reading lower than the others (about 50%, other 75%) when checked specific gravity. I tested voltage after batteries had been in the truck overnight, then unhooked from truck when testing.
I also thought about a glow plug/harness issue. The truck cranks for awhile before starting, 5-6 seconds sometimes, but not all the time. It starts up pretty quickly when warm. That's been going on for some time. Anyway, I will try to get a video of the rough start after cools down.
I am doing a side job and this thing has a rough idle. I put the scanner on it and pulled code 43 ESC and a ritch and lean code from the O2 sensors. I know the O2 codes are probably from running rough. It has been a while but could the knock sen be the problem or the ESC itself? I looked for the ESC by the throttle body but didn't see it. I remember what they look like but this is a late model 94 are they some where else?
View 4 RepliesI have a 2000 pontiac grand am with a 2.4 L engine it is automatic transmission. Th issue is i just bought the car from a lot thinking it was an easy fix. What happens is when i start the car it goes from a 1k idle to a 500 or lower and sounds like it might die or if i am at a stop light and decelerate too fast it also feels like its going to die and has a few times unless i keep the gas pedal pressed down. I read the codes at my local store they said it was a engine misfire, o2 sensor the front one, and the map sensor.
My farther works at a pull and save which is a lot to pull used parts from cars hes brought a used ignition coil, used boots , i bought new spark plugs and nothing was fixed there. we have replaced the maf sensor and the map sensor both with used parts neither fixed the problem. I am at my wits end here i cannot afford to take it to the shops around here and am trying to get this fixed to get back and forth to work. I may have left out parts that have been replaced, also as far as lights are concerned the check engine soon light is on .
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 RepliesMy brother-in-law brought me his 2004 Trailblazer that had an extremely rough idle and would die if ya thought about the air conditioner and all! So he had replaced the cam sensor, didn't work. He replaced the spark plugs didn't work. He replaced the fuel filter didn't work. So he asked me about it and ran across a fella talking about the CAM ACTUATOR SOLENOID and explained all about what to look for and such and low and behold new solenoid later purrs like a new one!!! It is look right above the power steering pump there is a plug in the side of the engine there with electric wires running to it.
One of the signs of being bad is oil inside that 2 wire plug just pull it off and look in it. Now to remove it you will have to take the power steering pump loose so it will move back out of the way so you can pull the solenoid out of the engine if ya get it out look on the end there are grooves running around it with little screens on them see if any are gone or coming apart, this usually sets a P0016 code which is stuff interfering with the sensors inside. If there is any oil in the plug or any screens missing then it will have to be replaced.
97 chevy k1500 with 305, engine rebuilt by shop 60k ago, last few months only drove truck 4-5 times, last time driving gave p0306, new plugs, wires, cap, rotor, cleared code, now gives p0300, took intake apart removed spider, sprayed/scrubbed each injector and poppet with cleaner, but no way of cleaning the line between the injector and poppets. No change after cleaning. Also ran injector cleaner through tank. All vacuum hoses look in good order, sprayed carb cleaner around intake to check for leaks at intake/throttle body, no leaks.
Checked TPS, IAC, MAF, Coil and fuel pressure, all good except fuel pressure was 52-54 while idle, replaced fuel pump, screen filter and main filter, cleared code, rough start and rough idle still gives p0300. Checked coil with ohmmeter, between posts A & C, Chilton says 0.1 ohms, i got 0.5 ohms, went to autozone and had them check a new coil, it have 0.5 ohms......? Can drive at higher speeds and runs smooth, but idle is poor almost dies.Checked fuel pressure after pump replacement, still ~54 psi. Stumped and don't want to throw more parts at it without a proper diagnosis. Have a OBDII pocket scan tool, but can't find manual, will try to find manual and see if I can pinpoint the misfiring cylinders.
I have a 2005 Nissan Sentra with 74,000 miles on it, and it has had trouble starting for 2 or 3 years. When it started, I would turn the key and the car would almost, but not quite, start, and simply turning it off and trying again would work immediately. I had the battery replaced and the spark plugs at ~50,000 miles to no avail. About a month ago, I started my car and it had a really rough idle for about 15 - 30 seconds and the check engine light came on (registered an emission issue), but it ran fine. I had to get a routine oil change and emissions test anyway and they checked the spark plugs as a first measure. They all had some wear, but one was almost worn down to nothing, which the mechanic said was a result of the spark plugs (autolites?) so they replaced them with the Nissan recommended NGK kind. The next day my car didn't start the first immediately, but on second try worked. A week later I noticed my car sometimes rumbling on idle right after start again, so they replaced the fuel filter and the fuel pump. Didn't work, I still have a rumble about 30% of the time when I start, and just two days ago the check engine light came back on (I haven't had time to get it diagnosed yet). Without knowing much about cars, it feels like the engine isn't getting enough fuel or something. Could it be dirty/clogged fuel injectors? Should I be worried that my spark plugs were worn down after just 25,000 miles?
View 10 Replies4 cyldr has very rough idle along with engine shake. Just started doing this. I replaced the cam sensor a few months ago and all has been well. But it started running so rough, almost like it jumped time. I was disconnecting sensors to see if motor idle changed and when I unplugged mass air flow sensor on air filter intake tube, nothing changed. Could this cause such a dramatic idle ?
View 2 RepliesI have a 2000 Accent with about 150,000 miles on it. Recently I have noticed that when my car is sitting in an intersection, the car appears to idle roughly. I would't exactly say that the car is idling rough, cause it stays at a consistent RPM while in drive or park, but the engine gets louder and the steering wheel starts to vibrating. When I slightly step on the gas, the vibration goes away. Also, when I put my car in park or neutral, the car quiets down and the vibrating stops.
I was wondering if it could be the throttle position sensor, or maybe a broken motor mount, but I haven't had a chance to look into it it. I did replace the purge control valve last week, which slightly improved the vibrations.
I have 2000 ford windstar with 3.8 engine. I have been reading up on the idle problems with these vans. However, most responses are in regard to the engine stalling and/or it trips a code. My does not do this. Sometimes the idle is rough and other times everything is smooth. I am thinking it may be an egr valve or dpfe valve.
View 5 RepliesI have a 100% stock 2004 Celica GT ~125,000 miles. Over the last few months I have been getting a rough idle and stumble at low rpms. The other day the car would not restart after sitting for about 20 minutes. Only recently has it actually thrown a DTC. The error codes were for misfires (P0300, P0301,P0302,P0303, P0304). I don’t get a code every time but the problem seems to be more noticeable if the car has been ran for a while, sits for 20-30 minutes while in a store and then when I try to start it when I come out of the store is when the problem most often occurs. When it restarts it will stumble at low RPM and if I hit the gas it has little response and misses badly. I have never used a scanner until now. I am using a Autel MS509 scanner and I am not sure it is giving me the correct diagnostic numbers for the live data. I think the DTC are correct but the live data is questionable.
Here is what I have done so far.
- Cleaned IAC valve (completely removed and cleaned)
- Searched for vacuum leaks using carb cleaner
- Cleaned MAF sensor
- Replaced all 4 injectors
- Replaced upstream and downstream O2 sensors
- Replaced Coolant Temp Sensor
- Ensured cam tensioner is providing adequate pressure to the cam chain
- Tried 2 sets of new Iridium NGK plugs and a new set of Bosch Copper plugs
- Moved coil packs around
- New air filter
- New fuel filter
- SeaFoam through intake and gas tank. I have not mixed in the oil.
- Compression Test (1=190,2=190,3=160,4=178)
Things I have not done.
- Taken it to the stealership
- Fuel pressure test
- Valve Clearance
I am concerned about the compression test because according to the service manual it should be around 218. I was using a Harbor Freight compression tester and I am not 100% sure I had a good seal with the tester.
Driving home from work this evening and engine light lights up, also car started to idle very rough.... long story short got the car home and checked with vag com... 2 engine codes
000768 - Random/Multiple Cylinder Misfire Detected
P0300 - 001 - - MIL ON
Freeze Frame:
Fault Status: 11100001
Fault Priority: 2
Fault Frequency: 1
Mileage: 86567 km
Time Indication: 0
Date: 2012.12.31
Time: 14:26:57
[Code] .....
After looking around online found out it could be a variety of reasons... gonna change spark plugs tomorrow hoping that's the problem... next cheapest fix would be the ignition coils... I'm just hoping its not internal, like piston or rings.
It's a 2007 Passat Wolfsburg 2.0T.... just went over the 53k mark.