I have a 2001 Ford ZX2 with 170,000 miles on it. The clutch pedal doesn't engage the clutch until it is almost touching the floorboard. I thought it had a hydraulic clutch being a 2001 but I can't find a reservoir for the fluid so now I must assume now that it is a mechanical clutch.
1. Does they hide the reservoir on these ZX2's?
2. What could cause the clutch issue?
I have a 92' Escort GT and the clutch started to act up, it's not burnt cause it is fairly new. The clutch pedal feels slightly looser when pushing it to the floor, the feeling like a cable snapped or something?
I'm pretty sure the clutch is a hydraulic one, not 100% .. Is there a hydraulic reservoir that somewhere that might be low?
I've test driven a used 2003 (155K) I'm considering purchasing. But the clutch is so stiff, especially compared to my 93 Accord. What makes a new clutch, pressure plate a throw out bearing so hard to engage?
View 9 RepliesI went driving today and for a moment I could engage/disengage the clutch pedal with little to no effort. It goes back to the normal force after 3-4 shifts.
It's the exact opposite of what's happening in this thread. [URL] ....
I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
1988 Acura Legend, 2.7L 6 cyl., 181,000 miles only do 6,500 miles a year to train station, parked inside, runs great. Last week parked out in hot sun, '90s, for 8 hours. At first, no problem. When did errand and returned to car, pushed clutch pedal and it would not return or allow gear to engage. "Jammed" into 1st, then could not shift, shifted slightly by pulling up on clutch pedal with my foot. Parked overnight, cool, next morning seemed to be fine and crept to mechanic. Mechanic road tested and found no problem and now seems to be working okay. Would parking in sun, high heat cause "clutch cylinder" to "seize" or "freeze"? Is there a "fix"? Also, increasingly hard to get parts for this car.
View 6 RepliesSo I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 RepliesMy clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad... 2007 Honda Accord Manual Transmission
View 8 RepliesAlright so I've had this car for about six months now and the clutch was supposedly replaced by the dealer I got it at. The clutch usually grabs about half way up but sometimes it's higher. I replaced the master cylinder because it blew out, when changing my I take I noticed the slave was starting to leak so I replaced that about three weeks ago. Ever since then, the clutch seems to grab differently and seems to be taking longer to engage.
Now, I did the "slave mod" on the old one AND the new one so it's not that. Do you guys think the new slave is bad? I have high temp dot 3 in there (I try to only use the best fluids for my cars). It just doesn't seem to grab as hard as she used to. Like it takes a bit longer to engage. The clutch (should) only have 15k miles on it. The clutch parts are under warranty but I'd still have to pay for labor since it's a wear part. I'd like to avoid replacing it if it's that new u less it's definitely going.
I purchased a 2001 Prius with 123K miles about two weeks ago. I knew the HV battery was shot when i purchased it. I decided to see if I could rebuild the HV battery on my own.
I'm very mechanical but not the brightest bulb in the room when it comes to batteries and anything electrical.
So here is where I'm at so far:
- I removed the HV battery.
- safely rested it on 2 horses (I used horses because it would give me easy access to the bottom to remove the bottom screws)
- Removed all 38 modules from the battery pack
- cleaned the busses in vinegar
- inspected each wire that connects between buss and the nut.
- tested each battery ( one of the batteries tested at -0.1, the others tested at 6.8)
- I don't know how to load test the modules, so I couldn't tell if they would drop dramatically under load, so I ordered 38 used replacement batteries off of Ebay. (Gen II)
- these replacement modules were about a half inch longer than my original modules.
- The replacement modules arrived. I cleaned the terminals, tested each one and installed them.
- Connected the battery back into the prius.
- Installed new 12V battery from the Toyota dealer.
- The Prius started right up.
- Drove it around for the first time for about 10 minutes.
- When i was driving it, the monitor in the Prius would show the engine running most of the time but sometimes it would show it charging the HV and other times charging the 12V. the engine would shut off at stop lights and resume when I pressed on the gas pedal.
- while driving back into my driveway, all of the warning lights came on and the battery fan kicked into high gear,
- I can't remember the code I pulled but it was in reference to the cells being out of balance I think. I'll have to check it again tonight when I get home.
- I removed the HV and tightened the nuts around the busses hoping the issue would be resolved.
- I was able to drive it only a few minutes before the issue returned.
other issues I noticed.
While waiting for the replacement batteries to arrive, I did the following:
- changed the cabin filter
- did an oil change.
- changed the tranny fluid and removed the tranny pan to clean out the slime and clean off the magnet.)
- changed the rear brake shoes.
- changed the front brake rotors and pads. ( they were in awful condition due to sitting so long)
***when I pressed on the brakes, only the rear brakes seem to engage, not the front. I never attempted to bleed them because I know only the dealer can do that)
I drive a 2001 Elantra, 5 speed manual, about 135k km on it which is about 85k miles. Yesterday I felt the clutch pedal was engaging unusually low or was not as resistant to the weight of my leg as is usual. I could drive it without much trouble though.
This morning the pedal went all the way to the floor with virtually no pressure exerted on my half, and shifting gears was pretty much impossible without excessive force, so I parked it and walked to work instead. It felt like I was shifting gears without stepping down on the pedal, even though the pedal was all the way to the floor.
I then checked the fluid in the reservoir and it was at the max, but it was black like oil. I've done some reading and I'm thinking replacing or cleaning the master and slave cylinders could work. Am I way off?
In every other manual transmission vehicle I have ever driven, the clutch pedal engages/disengages within an inch of the floor. Is it normal that the clutch in my 2002 Hyundai Elantra engages when the pedal is so far away from the floor? When I say far away from the floor I mean within an inch of the pedal being fully released.
View 21 RepliesI recently (1.5 months ago) had my clutch replaced because my clutch pivot ball was making noise and with 70000 miles on the clutch, the mechanic suggested replacing the entire thing. The clutch works beautifully, except that just recently my clutch pedal has started to make a squeak/ creak noise. It's not very loud, although it seems louder when it's particularly hot and muggy. It sounds like it is coming from the pedal and it makes the noise regardless of whether the car is on or off. What might be causing this?
View 3 RepliesI'm looking for a part number for the rubber stop that mounts behind the clutch pedal on the firewall for a 2001 Ford Ranger 4cyl 2.3L 5spd Manual. Can't seem to find it on the web. It looks like it snaps/presses into a mounting hole behind the pedal. The original one decided to disintegrate and now I get a nice knocking noise when ever the pedal is depressed.
View 7 Replies95 Ford Escort 1.9L, 330,000 miles. Never changed the clutch and i bought it with 80k on it. With that said the clutch never slipped and a lot of this is highway mileage so i never saw a reason to change the clutch just because.
Last week i pulled into the driveway i depressed the clutch pedal as i normally do and as i slowed, the car bucked like it was still in gear and didn't recognize the clutch was depressed. When it started bucking i tried to pull the gear shifter to neutral but it wouldn't move, the car finally died in it's parking spot. I quickly popped the hood and had my son press the clutch in and out and all components seemed to be moving fine, i was mainly looking at the slave cylinder assuming since it's a hydraulic clutch if it was a hydraulic issue that wouldn't move if i didn't have hydraulic pressure.
No obvious leaks were noted, i looked at the master cylinder and it seemed a little low but not empty maybe just above min. I filled it to max and still no change. So i assumed it was the clutch finally disintegrated and locked up. Yesterday i got in the car to attempt to move it to the garage to work on it. It started up fine, shifted through all gears with no issue's, drove it around for about 15minutes shifting a lot and pressing the clutch randomly and it worked fine.
I brought it back home and tried to kill it a few more times before i got it to the garage, it finally locked again but it was in neutral and i couldn't get into any gear. Turned the car off and then restarted and it shifted into gear, i pulled it into the garage and stopped with no other issue's.
Checked closer for leaks, between master and slave and couldn't find any. Pulled speedo cable and checked trans fluid, its brownish red (more brownish) and thin but didn't really smell burnt and it is at the correct level. Linkage has some slop in it but i don't see it binding anywhere, i layed under the car and was able to move linkage in/out of gear with my hand. It's easy enough to say the clutch is well over due for changing but since there were no signs of a failing clutch when i drove it i think i need to look elsewhere.
Could it be worn fluid? Could it be debris in the line? Or could it be that the fork just isn't engaging or disengaging properly due to wear?
I drive a 1995 Ford Escort (don't laugh, even though it has 328,000 miles on it). The car is generally very reliable, despite its age. The one thing that repeatedly fails, however, is its clutch cylinders. The factory cylinders lasted about 150,000 miles. The after-market models, ever since, have failed almost like clockwork every 18,000 to 20,000 miles. Either the master or slave has had to be replaced.
The longest they've gone is about 29,000 miles, but then both had to be replaced. No mechanic who has seen this car can explain why it would eat clutch cylinders so regularly. The only clue I have is their proximity to the firewall, and this model Escort was recalled for firewall problems early in its life. Why clutch cylinders would fail so regularly, and what I might be able to do to prevent it?
I have my suspicion about what is the culprit, and well, the likelihood of it contuing to work.
Occasionally when I am at a stop and try to shift into gear with the clutch depressed to the floor, it does not want to go into gear. So far, I have been able to wiggle the shifter around, try a few different gears then go back to first and it works. Also at a stoplight today, with the clutch depressed to the floor for a few minutes with the car in 1st, after about 3-5 minutes the car started to slowly creep forward.
What are your suspects on this one?
I have a 1999 Winnebago Motorhome on a F53 Ford V10 Chassis and the A/C clutch will not engage when turning on the A/C. I have check the Freon 134A and it appears to be fine (in the red zone) and actually put a jumper across the pressure switch connector (harness side) and it still will not engage. Is there a fuse within the circuit if so, where it may be located?
View 1 RepliesMy daughter has a 2003 Saturn Vue 2.2 and it seems that the clutch if froze up... I have checked Freon level with a gauge that I use to top of Freon and seems ok... the vehicle has 170,000 thousand miles... are these compressors prone to failure and is there a "Quick Fix" without replacing compressor, orphis tube and dryer?
View 3 RepliesI traded for a 99 passat 1.8t aeb based on the assumption the slave cylinder was out. My 3rd b5 5 speed. Kid told me clutch pedal had no pressure and fell to floor.easy fix! Get the car to my house from 2 hours away and this is not the case.Pedal is fine. Decent clutch pedal starts with clutch pushed in. But clutch does not engage. Even when motor off or on goes into all gears without clutch pushed in. no engagement. So I put in new slave and bleed out.
Car no longer stuck in neutral shifts fine. Put in reverse barely crawls but is MOVING! Put into first and start to pull forward..stops moving. No clunks or booms just back to ALL neutral. starts with clutch but wont engage. So try bleeding again nothing.. I think it is the clutch but i dont want to spend 1400 if i dont have to though the car is worth it. Going to replace dual mass as well. The cv joints are fine. so thinking throw out or pressure plate. i work on this car like crazy but im definitely not going to do the clutch. Not enough time or a warm dry location. I haven't checked clutch master yet but with slave bleeding out,no leaks and a firm pedal i dont believe she is the culprit..
if the fan doesn't work, could this make the AC compressor clutch not engage? I think the fan is burned out because it doesn't spin at all, and only moves with a lot of effort. If the fan circuit is open, will this cause the Compressor to not work as well? the car is a 1991 740 GL. 2.3L engine, non turbo.
View 3 Replies