Escort :: 1998 ZX2 - Car Started Misfiring
Jun 27, 2014
I have a '98 ZX2. Recently, my car started misfiring. I'm not sure of the cylinder number, but it's the one closest to the driver's side. Long story short, I found that the fuel injector is not firing, if that is the correct term. I used some trick I learned on youtube which involves using a screwdriver to listen for the fuel injector clicking. Anyway, I made a noid light out of an LED and a couple of resistors and found out that there is no injector pulse. I know the noid light works because I tested it on the other cylinders and it flashes. Anyway, I'm not sure where to go from here. I've read elsewhere it could be the PCM but if that were the case it would probably affect every cylinder and if it was a crankshaft position sensor the car wouldn't start.
View 5 Replies
Advertisement
I was driving my '98 Jeep Grand Cherokee Laredo (6cyl 4.0l 4 wheel drive) on the freeway when it, very suddenly, started shuddering badly. The check engine light came on and then started blinking. I pulled right over and shut it off. I stared it back up and the engine is misfiring badly. I had a code reader with me and it's showing three codes. A random misfire, a cyl #5 misfire, and a Cyl#6 misfire. It will sit and idle (very roughly obviously).
There was no drop in RPMs, oil pressure, voltage or anything when it happened.
I got it home and replaced the distributor cap/rotor, all six spark plugs, and the plug wires but there is no improvement. I cleared the Codes and re-read them and got the same errors again.
View 4 Replies
i have a 1998 escort se when i park the car on a slant it leaks gas it has been leaking for about 2 weeks now. The other day i parked it on driveway it is up hill the car would not start so i push it down to a straight surface it started now i see the car is stalling now. Could it be fuel pump, gas tank or something else...
View 3 Replies
I have a 1998 Ford Escort ZX2, 2.0L DOHC. I recently had the check engine light come on with code that basically says my VCT solenoid is malfunctioning. It is not very easy to find information about this part, I see that it is expensive, and time consuming to replace. I don't really have the time or money, the car still runs with 120k.What kind of consequences would I run into if I decided not to replace the part. The only thing I can find is that I would not pass emissions.
View 4 Replies
I recently replaced a bad head gasket on this car. After putting the reworked head back on the engine and putting everything back together, I can't get fuel to the engine. I cheated and took the intake manifold out and bolted it to the head and then set it back in the car plugging my injectors back into the manifold once in there. I checked all my electrical connections and they are all good. I am not getting power to the fuel pump, which was replaced a year ago when I first started tinkering with fixing the car. I get power to and from the inertia/fuel cut-off switch, but it doesn't appear to get to the fuel pump. I checked all the injectors to make sure they were seated properly which they were and all the fuses both under the dash and hood that I know about and then some. When I pull the 30amp fuse under the hood, and replace it, I do hear a sound that sounds like something is pressurizing or pumping for a second or to, but the sound is from under the hood and not from the pump/gas tank area.
View 2 Replies
I just recently purchased a 1998 ford escort. the gas gauge constantly at half. I haven't driven it yet because my insurance kicks in in a few days.
I asked my friend about it and he said that some cars always gauge the amount of gas no matter if its running or not. Is my escort one of those cars? or is it just broken?
View 1 Replies
I have a 1998 Ford Escort which I drove about 450 miles in frigid weather over about 8 hours in mid January. After arriving at my neighborhood and getting off the expressway, I couldn't get the idle on the car (manual transmission) to go below 2500rpm's. Further, upon taking off, the car was trying to stall, and I was forced to feather the clutch through town driving and keep the throttle up so it wouldn't stall, even with the clutch in. The weather at the time was about -7 degrees (f). The next day the weather continued, and thee car would start, jump to the same idle for 10 seconds, then drop suddenly to 500rpm, then stall out. I wrote the car off, cleaned it out over the next week, and then I tried to run the radio while doing so last weekend. I got the car to start, and run normally. I think it may be a computer issue, but it may also be the temperatures. The car has 207,000 miles on it.
View 3 Replies
98 Ford Escort SE
Been having acceleration issues with the Escort for a while now. The repairs I've made on the vehicle so far are; new fuel pump, coil pack and mass air flow sensor cleaning. Those are in order.
Now onto the issue. From a dead stop and sometimes while driving my vehicle will give acceleration issues though mostly from a dead stop. Checked the tranny fluid and it was a light brown with bubbles(?) so thought I'd do a fluid change but with the work required wanted some input before ripping into it.
View 19 Replies
1998 Ford Escort SE ... On idle ( at a red light or in park while on) it shakes terribly. When I shift into N it will lessen for 3-10 seconds, but then it will cycle back to the vibrating. The spark plugs were replaced about 4 months ago and got a brand new transmission 5 years ago this coming summer. It came into the family in '00 and I got it when I turned 16. The vibration started about 2 years ago and at first I was told "little car has shaky engine". When it got worse I was told it was the motor mounts, which I replaced a year ago. When they were first put in the car ran smooth as ever.
My mother turned on the AC while I was taking her for a test ride that same day and it started back shaking. They said the motor mounts were perfectly in place, and that it was a broken fan blade. My husband and I just don't see a fan blade causing that much shaking. I can hear the car violently vibrating when I park and take pizza to someone's door. Also a more minor problem, ever since we put new brakes on, my brake light comes on too easy. The weight of the peddle will turn the light on, and I have to keep using my foot to pull it up after each time I touch it, and sometimes when I'm driving.
View 12 Replies
98 Ford Escort SE... Was changing out fuel filter and noticed the bottom (filter sets upright) snap holder the broke. Would I be ok with just cutting off some of the metal line and adding flex/rubber and using clamps?
View 5 Replies
This problem showed up this summer, different times under load: on hot days, going uphill, AC on. Also, always happens when the temp gauge is just above halfway. Even after a stall, I am able to limp home, and it improves the longer the car runs after the problem starts. First I replaced the fuel filter which was pretty dirty, the problem didn't improve, so had the shop run codes -- low ignition voltage. They replaced the coil, and that seemed to work for a while. Now, in109 degree heat, it's starting to hesitate again, but the engine light hasn't come on this time. I had to replace the radiator about 4 months back, when it was cooler, and don't know if it's somehow temp related. Also, haven't replaced the timing belt since I bought it with 90K (its has 119K now).
View 3 Replies
Iv got this escort from my sister, i assume it has been hardly maintained considering the... state. I bought it because she was tired of dealing with the problem... driving, it will turn off. She said it got to the point where she just stopped driving it, although it only happened twice. It began when first time it shuttered then died. Took air filter off and it only ran it like that to get it home. Now it doesn't run but for a few seconds even without air filter, so Its the best choice to leave in.
Anyway, I've replaced:
-PCV Valve
-Fuel Filter
-Some dry-rotted hoses
-I didn't replace it, but i cleaned throttle body and MAF sensor in the intake.
I've tested alternator and batter, both are good. I tried fuel treatment. Being honest this is the extent of my.. automotive understanding. But Im fairly certain it is a fuel system problem.
View 1 Replies
I have a 97 escort that was running great after a lot of maintenance work and then on the freeway it started to loose power. I pulled it over and it died. It would not restart for about 15 mins then it did. Ran really rough, mad some noises, I got it home and now it won't restart at all. It is not the battery or starter. Is it possible a bad EGR valve could cause it to do this? About a month before this happened I replaced all plugs and wires, coil, fuel filter, battery, oil change and O2 sensor.
View 2 Replies
Car started throwing PO304 and checked coil, plugs, wires and injectors before finally checking compression. Checked #4 and it was 70. Checked #3 and it was 150 something. Got mad and quit
3 weeks ago the CEL started coming on only when i was low in a gear. Like rolling to a stop sign and taking off in 2nd instead of 1st. Dogging the car to avoid downshifting i guess i would say. Car would jerk like crazy and throw a code but would drive out of the jerking and run fine.
There are no loud noises coming from the valves. Engine runs a lil rough at idle but you would not notice it after you get going. Spark plug #4 had some oil on the threads, others did not. No antifreeze in oil, looks good. Throws PO304 constantly now..
Buddy came over and said he would first check the timing belt to see if it had slipped before digging into the head. To tell the truth, i probably will not be digging into the head anyway's. I probably could not find the problem anyways.
Just wondering what could be some realistic explanations for losing most compression on one cylinder. Could the valve seat be getting ready to go or is that a all or none type of deal?
This is a 97 wagon with 314,000 miles. I am getting 37 MPG and it drives straight as an arrow. Just replaced all tie rods and brakes and had her front end aligned and this is how she treats me. Would like to save this car as i really like it for my 700 miles a week commute to work. Judging the price of used cars nowdays, i have thought about replacing the engine with a used one if it comes to that but we will have to see.
View 5 Replies
My '98 4.0 has 213k on it and the other day I started the engine and the jeep started shaking like crazy. Eventually the engine quit and refused to turn over so I looked under the hood and quickly discovered the problem, a deteriorated rubber elbow on the left manifold. The elbow connects to a threaded breather type valve in the manifold and has a thin piece of black plastic routing to the purge solenoid next to the left fender/air box.
When I removed the rubber elbow from the manifold the engine eventually turned over and idled fine, I then headed to autozone and found replacements of the same diameter, I cut them down a bit to match the length of the originals. Since its been a while I changed the plugs and wires, coil pack along with cap and rotor while I was at it. I replaced one plug and wire at a time to ensure I didn't mix things up, same goes for the cap. Now the jeep seems to take a few more seconds to get started but once it does it idles fine.
Now when I hit the gas hard the jeep will hesitate and then backfire. If I'm smooth on the gas the jeep drives good, whether city or highway. When coming to a stop the jeep will sometimes buck slightly like it wants to cut but doesn't. The backfire sounds like its coming from the air box and oddly enough, my aftermarket radio no longer plays in the accessory position, probably a separate issue. So far there's been no check engine light.
I really need to keep this jeep for a few more months and I would hate to put big money into at this stage.
View 3 Replies
I have a 1985 Ford Escort which I have to keep parked outdoors at the bottom of a very steep mile and a half long hill. It's right next to a river and very damp and cold and I only use the car once a week, very early on a Saturday morning. It takes at least five minutes of cranking to get it started with full choke. I then have to pull away up this 1 in 4 gradient hill with four of us in the car. About half a mile up the hill there's a junction and if I have to stop at this the car will often stall and be very difficult to restart. If I keep the choke out it will crank and crank and crank. If I push it in it will fire after a few tries but won't stay running. Having problems on really steep hills with cold engines and a manual choke?
View 1 Replies
I've been out of town a bunch and my car has been sitting out at the airport. I picked it up last friday, drove it home. Today on my way to work the car started jerking - like the engine was trying to rev slightly. When I put it in park, and listened, the engine was jerking or misfiring maybe. The exhaust was a bit louder than normal as well and i could hear the stress in it. I also smelt a strange burning smell. I've called and had roadside assistance pick it up and take it to the dealer.
View 7 Replies
I used fuel injector cleaner in two different gas tanks; the car started shaking and the check engine light came on. The mechanic changed a sensor but the car was doing the same; I was told that it will take 4 full gas tanks to clean the gas lines. I went to autozone and they told me that the car had a misfire on cylinder 5 and multiple misfire as well. I do not trust the mechanic any more since I had to take the car back to them several times and still is not fixed. They also did a full tune up and the check engine light still on and flashes when I am going about 55 mph.
View 3 Replies
How to repair a 2009 mini cooper that started misfiring? What is the most common cause for misfiring?
View 19 Replies
I have a 2011 Hyundai Accent 1.6L. A few weeks after I bought it w 38,000 miles, it started misfiring so I replaced the spark plugs. It ran great for about another 6 months and started misfiring again. I took it to Hyundai to have it fixed and of course it wouldn't do it for them. I told them what it was doing and they said that there was no code so it was probably my spark plugs. I replaced my plugs with the OE plugs and got the same trouble about 4 months later. Now it has 60,000 miles and my warranty is done. I put in new plugs yesterday and it only ran well until it warmed up and it did the same thing. I ordered new, better than OE Delphi coils yesterday and I'll get them today. I feel like there's a bigger problem with the system that's causing the problem with the coils.
View 7 Replies
I got this 98 Ranger 2.5 that I've done a tune-up on less than 30,000 miles ago. I changed plugs, wires, and both coil packs. Timing belt, thermostat, fuel pump, fuel injectors are all recently changed too within a year or two. Fuel filter and air filter I change every 30,000 miles. The truck runs as great as a 4 Cylinder will run. It's at 344,000 miles but the engine was changed once so it probably has over 100,000 miles on it. There is just a slight miss you can hear through the tailpipe but it's not severe enough to be picked up by the Check Engine Light. In fact, even when the coils were totally gone it never put up the Check Engine Light. I can tell when a coil pack is going out on this because it's done it several times so I usually just change them with the tune-up. It's only a slight miss some people may not even notice it. I was just wondering is there any way to track down where the miss is? I tried looking under the hood in the pitch black and there's no plug arcing.
View 1 Replies
