I have a 92' Escort GT and the clutch started to act up, it's not burnt cause it is fairly new. The clutch pedal feels slightly looser when pushing it to the floor, the feeling like a cable snapped or something?
I'm pretty sure the clutch is a hydraulic one, not 100% .. Is there a hydraulic reservoir that somewhere that might be low?
2014 Passat... I've got a little over 2,000 miles on mine now and I really do like the car. However, one thing that is really bothersome to me is----the brakes.
I'm not sure if it is specific to my car or to the passat in general. Here's the issue:
When applying the brakes, the pedal feels almost loose, as though the is no pressure on it, but once you push the pedal down far enough the brakes come on heavy, hard and fast. It's like turning on a light switch.
I am wondering if this is an adjustment that I can have done at the dealer to put more feel into the brakes or if this is just something that we all have to live with, of if maybe there could be something wrong with the brakes on my car.
M/T 2010 Sonata. I'm just out of warranty at 102,000 mi. No issues before with clutch. I noticed a clicking or crunching sound when pushing the clutch pedal down. I took a gander and noticed the pedal was traveling farther than it used to because there were indentations in the carpet. So this happens for about 3 days. Then I start the car and cant get it into gear. If I shut it off, it easily goes into gear and I can drive. Usually it is ok after that point but is getting worse. Mechanic briefly tried to bleed it but the pedal stayed on the floor. He was able to get it to its original problem but said if he replaces the master & slave cyl then might as well do a new clutch. Because I had no slippage, no pedal issues or anything prior to clicking. Is 102k miles and 6 years usual time for these components to fail?
View 2 RepliesI started having a strange clicking sound when pushing down the clutch pedal. I have 43,000 miles on it and I have driven the clutch well(I really don't believe I already worn it up). It goes away and then it comes back. There is no problem on shifting from gear to gear, it works just fine. It is only when I push the pedal that it starts clicking like it pushing against something. The car dealership was so useless, they said I need a new clutch and that warranty does not cover it because I may have been using the clutch badly. Also do you think that they have the right to tell me it is my fault even though I have the extended warranty for 100, 000 miles.
View 6 RepliesI have my suspicion about what is the culprit, and well, the likelihood of it contuing to work.
Occasionally when I am at a stop and try to shift into gear with the clutch depressed to the floor, it does not want to go into gear. So far, I have been able to wiggle the shifter around, try a few different gears then go back to first and it works. Also at a stoplight today, with the clutch depressed to the floor for a few minutes with the car in 1st, after about 3-5 minutes the car started to slowly creep forward.
What are your suspects on this one?
I have a 2001 Ford ZX2 with 170,000 miles on it. The clutch pedal doesn't engage the clutch until it is almost touching the floorboard. I thought it had a hydraulic clutch being a 2001 but I can't find a reservoir for the fluid so now I must assume now that it is a mechanical clutch.
1. Does they hide the reservoir on these ZX2's?
2. What could cause the clutch issue?
Still chugging along!!
So, I haven't been the kindest car owner to my poor little hatchback. I do my best to get regular oil changes, but other than replacing the brakes last year, I have not kept up with most of the manufacturer's suggested regularly scheduled maintenance. The car has about 130,000 miles. Manual Transmission. My clutch feels a little loose, and I have been noticing a slight grinding sound when shifting (only from neutral to first gear).
I changed my oem clutch in my mk4 golf 2.0l with a stage 1 ecs tuning clutch kit. Lightweight flywheel, clutch disk, pressure plate and throw out bearing. But since I have my clutch pedal has been less stiff then usual. I like my clutch pedal as stiff as possible but it just isn't I bled off the slave cylinder. When I was done no air was coming out but it is still way to soft for me. What should I do next??
View 6 RepliesI have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 RepliesMy buddy just bought a 1992 f250 460 the brake suck the pedal goes to the floor don't know if master or the booster or the rod needs to be adjusted or what the brake look ok and it stops ???
View 7 RepliesSo my clutch has been acting up lately. When it sits for a few hours the clutch engagement point seemed to creep down but over the course of 35 minutes of driving would work its way back up again. Today it was unusually low and wouldn't let me get it into gear. I tried pumping it a few times and realized it wasn't coming back up all the way, I pulled it up and then tried again and it just dropped right to the floor where it now sits. Fortunately I was at work and can hang here until my ride arrives, and will just wait until late tomorrow night to drive it to my shop without stopping...
My guess is I need a new clutch master cylinder. I have plenty of fluid in there although its a bit old so I'll be changing that when I change the cylinder. Could it be the slave cylinder? If so is it a bear to change that? (do I need to drop the trans?)
So over the weekend my clutch pedal stuck to the floor 2 times and would not come all the way up on several occasions. It has since then stopped doing it. I am wondering if I should bleed my clutch or not. Flush and change fluid?
Just concerned it may turn worse.
Facts: 1999 Vw passat 1.8t
1 year ago, clutch pedal would not come up off the floor, no life in the pedal.
Problem: Clutch master cylinder, replaced.
6 months ago, clutch finally went bad. Took car to clutch shop, replaced clutch kit(found out after i payed that they only turned the dual-mass flywheel... ). Get car from clutch shop, the clutch pedal came up only 2-3 inches off the floor by itself but you could lift the pedal with your hand or foot, and it would come back up all the way, but it was life-less. It was not pulling fluid in. It was catching extremely low. I called the shop, they said that it was just because it was a new clutch and it would get better. I didn't believe them.
Two days ago, I got into my car and couldn't get it into gear. Clutch pedal would go down with the same amount of force as before. Took it back to the clutch shop and explained the history with the clutch master and then them doing the clutch kit. They said it wasn't bleeding properly and they're not sure if its going to have problems again. Car is working now, but I am concerned that it will have similar problems again.
The tech who fixed it said he pumped fluid into it extremely hard, and that's what made the pedal come up all the way (no longer stops 2 inches off the floor) and its going into gear just fine now. What the problem might have been? Block in the hydraulic lines? If this is the case, does forcing fluid through it fix it?
My clutch pedal went all the way to the floor. The engine was missing first and then that problem happened with the clutch. I had the car towed to my business, I checked it the other day and the pedal was up. The clutch still doesn't engage.
View 6 RepliesComing to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 RepliesLast night I was driving home and decided to show off at a light. I punched it pretty hard, but it wasn't anything outrageous.. anyway, as soon as I shifted to second, my clutch pedal gave out and dropped to the floor without resistance. I coasted it to a gas station, luckily.. When I lifted my foot the pedal rose back slowly. I tried pumping the pedal, didn't work. I looked for leaks, but none were found. I turned it off, put it in first and tried starting it, and it turned over and jumped/jerked forward, a lot like it did right when I shifted into second and it went out. So I'm assuming that its not the entire clutch cause it wouldn't have engaged the engine. It's not a leak. pumping it didn't work so it's can't be a pressure issue.. what is going on? is it my master cylinder, or maybe my slave?
View 7 Replies1998 Passat 1.8T FWD. My clutch pedal is stuck to the floor and wont spring back up. I can't seem to find the little tank to check the clutch fluid. I have heard the it uses the same tank as the brake lines do, but the tank that holds the brake fluid is full. Can it be the slave cylinder is gone? or just got a air pocket in the line?
View 1 Replies2003 Jetta, 1.8T, 5spd, stock, 129k miles. I am working on a friends car and his complaint is the clutch pedal occasionally sticks to the floor and during this sequence it is hard to shift gears. I removed knee bolsters to inspect under the dash and found all linkage straight, all plastic parts/springs in place and no fluid leaks, I removed slave cylinder from bell housing and found smooth operation and no leaks. I guess I could replace both but I am wondering if there is a common issue. My searches have found broken plastic parts, bent push rods and leaking cylinders.
View 4 Replies1997 Ford Ranger w/manual 5 speed tranny
A few weeks back my clutch pedal seemed a bit softer than usual one day. Still it worked fine... no problems shifting. Today after a short ride it went almost to the floor before disengaging. Now I cannot get it in gear without grinding.
So cold out I'm not sure I want to tackle this right now, what to look for and where?
My buddy called and said his clutch pedal went to the floor on his 04 4.0 ranger. Said no fluid leaks or anything, so I suspect the slave cylinder went. He said the slave is on the inside of the trans and you gotta pull the trans to do the slave, so might as well do the clutch too. How hard is it to replace both these on this truck? I've done it on a 94 cummins, so the trans should be a lot lighter. just wondering how bad of a job it is to do?
View 2 RepliesSo this has happened a few times pedal drops with no back pressure then give a bit pull it back up by hand and it's fine has happened 4 or so times in the last year. I'm reluctant to replace slave and master cylinders could it be anything else? 87 Ford F-150 hydraulic clutch
View 10 Replies