Elantra XD (2001-06) :: Timing Belt Replaced Now Car Won't Crank Over
Apr 1, 2012
Changed the timing belt. Used the red mark up top and the cut in the block on the lower one to get TDC. Changed everything with new parts. Double checked the marks after the belts were on (rotated by hand through two full turns and checked to see if the marks were in the same spot). I followed the write up that was posted here by U95.
Anyway, the car won't start. It tries cranking, but won't actually start. There is fuel and the battery should be good to go. There shouldn't be any Fuel/Compression/Air issues.
I guess my question is: If the timing belt is not tightened enough, would that keep it from firing?
Also, in trying to crank it by key every thing sounds normal (no knocks or pings or valves getting bent sounds) and turning by hand gives just the little bit or normal resistance but spins nicely.
I'll probably take the battery to get it load (I used my tender to try and start it as well, didn't make a difference) tested tomorrow and then try the starter (shouldn't be bad though, only 60k on the car). Otherwise I'll have to teardown and start over.
View 13 Replies
Advertisement
I recently replaced the timing belt, tensioner, and roller in my car. Today I became concerned that I hadn't tightened the tensioner properly so I did a quick check (it was). I also noticed the timing belt felt a bit loose, so I tightened it to what I thought was about 1/4" deflection with 5lbs pressure—not what that feels like in that tight space.
When I started the car there was a noticeable whining sound. Before I changed the belt there was a slight whining sound (but there was no whine after I changed the belt). So I loosened the belt a bit and there's now a slight whine. I feel like the whine shouldn't be there but it's hard for me to imagine that the belt should be any looser since I can move it 1/4" inch without much effort.
So, should I be tightening the belt to the point where the whining is gone, or is a slight whine ok?
View 2 Replies
I just changed the timing belt on my sisters car and finished yesterday and drove it today. A check engine light came on so I went to check it out and P0016 popped up. I've done some research and people say that it might be that the timing belt is misaligned or loose. I tightened the belt not too tight but not too loose. Note: I also spilled coolant on the crankshaft pulley and a bit on the belt itself. The car idles rough when driving too. I will tomorrow take off the cover and check the tension of the belt.
View 9 Replies
99 passat 1.8t with 5spd has 95k on it. 2 weeks ago my ex wifes car broke the timing belt and bent 12 valves so brought it to mechanics to get repaired and got it back seems to start up fine but when shes driving it stalls out on her. Mechanic says its something do with electronic throttle and nothing to do with his work. No check engine codes yet anyways .
View 1 Replies
Today I had my 2004 1.8T Passat in the shop for a few minor things. The car has only 89,000 KM's (NOT MILES~ I live in Canada) on it. They told me that my serpentine belt was needing to be replaced (which I knew) and they recommended that I to my timing belt at the same time. They told me that you can buy a kit that has the timing belt, tensioner and water pump in it. Anywhere I have read it has said to change your timing belt at 120,000 KMs.
View 2 Replies
I just had my timing belt, water pump, etc. replaced at a reputable indie VW shop. I just got the car back and it seems to idle a bit rough. The car used to purr like a kitten but now it shakes a bit in idle. Seems to run fine but the idle is rough. I'm going to bring it back to the shop on Monday. Can the timing be off a bit? Will it ever purr like a kitten again?
View 2 Replies
Brought my car to a garage that someone suggested to have a new timing belt put in. After I picked it up I was having problems ((I would try and start car but it would take a few trys to get it started)I called garage told them i thought the timing belt needed to be adjusted. They told me that was not the problem but i needed some censor. Well now my car wont start at all so i brought it to another garage who tells me that the timig belt was placed wrong. My question is..Now what? lol. Do I ask for my money back seeing that they didnt fix it? Do i have the same garage just fix it?(i didnt like them in the first place so really dont want to go back. If i do ask for them for money back and they give me a hard time,what can i do? or who do i call first?
View 4 Replies
I just got my timing belt replaced by my mobile mechanic thats been doing it for years. I saw him do the work and get the timing right. When he was done the car turned on and ran perfect. After about a minute the car just shuts off. Now the car won't start at all. The car turns over but no start. The car ran perfectly before I had this job done.
View 9 Replies
My car has 103000 miles on it and the timing belt was replaced several hundred miles ago. After the service I noticed it had a bit of a rough idle and a very slight sputtering noise, but still no check engine light. Was the timing belt put on wrong? The engine is non-interference, by the way.
View 1 Replies
I have a 2007 Accent with 119K on it.
I wanted to replace the water pump and I was wondering if this can be replaced without removing the timing belt or the lower timing belt cover?
View 8 Replies
We recently had the timing belt replaced in our 2003 Volkswagen Passat (1.8T). Now it shakes and vibrates badly when we put it in drive and idle. It ran smoothly before we had the belt replaced. The mechanic hasn't found a solution yet.
View 2 Replies
A mechanic has my car and replaced my timing belt and water pump....he said he had it running and then it sputtered out and wont start..i have never had a problem with this car. Just replacing before it went out.. he is missing something.
View 19 Replies
So i just spent over $1700 at a vw service ctr having a sched 140k timing belt replaced with thermo and fuel filter. This was 3 days ago and when i picked it up it was slower to turn over then got worse and todsy it won't turn over at all even when jumped. It cranks and blows black smoke. Problem is i'm 160 miles from that svc center and it's sunday. There is a vw svc center 14 miles away but i feel like it needs to ho back to where the work was done because it ran great before taking it there.
View 5 Replies
I am deep into replacing the timing belt on my 08 Elantra 2.0, and am nervous about taking the tensioner off since it is not obvious how to set it. I could use a fool proof explanation on how to set the tensioner.
The Haynes manual talks about 1/4 deflection but that seems too imprecise.
I can not see the marks in the video : DIY 2008 Elantra timing belt video 2 of 2 - YouTube
And this post 2008 Elantra Timing Belt does not quite seem to explain. I am contemplating putting it all back together, just changing the accessory belts and handing it to a shop. I could use a fool proof explanation on how to set the tensioner.
View 7 Replies
To my knowledge, if the timing belt goes the engine shuts down. According to others on Hyundai forums, you can blow the engine in a Hyundai Elantra if the timing belt goes. Is the latter really the case?
View 9 Replies
I have a 2009 Elantra (automatic) that already has 52K miles on it. I drive a lot mostly at highway speeds. I know several people who recommend having the timing belt replaced BEFORE the warranty runs out at 60K miles.
The dealership has a 60K inspection where they "inspect" the timing belt (plus a whole lot of "fluff" checks, tire rotation etc) I'd rather just take it in and get it replaced. What should a timing belt replacement cost?
View 1 Replies
My girls family has had an 08 elantra 2.0 new since 2008 and I've been doing the work. I recently did the timing belt ( July) with beck arnley oem parts. 65000 miles. I replaced belt, idler, and tensioner.
Right after I did it there was a mild hum at idle. It somewhat did this before the belt so I assumed it was just the new belt in plus the very mild hum it already had.
Recently it is humming very loud and high Pitched. It gets louder with higher rpm. If I take the cover of and move the needle on the tensioner while it's running it quiets down a little but it's an auto tensioner and doesn't stay right where it needs to be AND even when it is at the ideal spot it still hums.
View 12 Replies
Looks like my timing belt broke. I was taking my car out of the parking lot, and heard the warning chime. I tried to look at the warning light, I think it was the malfunction one. I heard a belt/ fan snap. The engine stalled and I dint try to resart the engine. I had it towed to the dealership and am waiting to hear from them. The engine dint make mucg of a noise but sorta just died. Does this sound like a timing belt? I am worried abt the damage. how much would it cost if it was a timing belt? my car only had 73k miles on it. It is a 2001.5 1.8t.
View 5 Replies
I have a car Passat 2001 V6 and I need to know as changing the timing belt and the pump of water. Do I also need to know which the correct position of the timing belt is? As I know that this in the correct position and that the motor won't suffer damage. I wanted they could send me a diagram to see better as it is or that I use of reference to put it.
View 1 Replies
2008 Hyundai Elantra, 2.0 it. We replaced a bad water pump, and timing belt while we were there. I followed directions found on multiple websites. We spun the crank shaft to the top dead center mark on the crank sprocket/engine block, and the cam sprocket / assignment mark. Then removed tensioner, and belt. Installed new belt and ensured alignment marks had not moved. Applied pressure to tensioner and tightened. Reassembled everything else. Car started with no problems, drive for about twenty minutes started making clicking sound from under the hood, we turned around to come back home and the car still making clicking sounds gradually started to loose power and speed until the engine stalled and would not restart. Trying to find out what could have happened.
View 2 Replies
I just installed a new timing belt, balance belt, idler, and both tensioner pulleys but am getting a little whine. I adjusted the balance belt but the noise does not change. No other belts or items are hooked up yet this was a dry run. Car seems to run fine and idles well. The hydraulic unit seems to be working fine and it's a OEM Hyundai piece.
Anything common I can look for that should stand out? 2002 Santa Fe 2.4L
View 6 Replies
