Elantra XD (2001-06) :: Power Steering Acting Up Like Belt Is Slipping
Oct 16, 2013
Well, two years after I replaced the pump bearing and the power steering is acting up like the belt is slipping. Sometimes it works fine, sometimes the steering gets jerky and hard.
The fluid level was fine, but I changed out the old stuff anyway, the belt is fine and not loose. I also pulled the pump apart to inspect it and it still looks as good as new.
When it acts up at a stop, it will squeal, but like I said, the belt is not loose. It's almost as if the rack is bottoming out against the bump stop (it's not) or the valve that lets excess pressure is dumping pressure randomly.
I took the valve apart with the pump and it looks fine, no scratches. Do the rack or valve go bad? If so, what was that like and could my rack have a seal leaking inside?
View 3 Replies
Advertisement
Due to being low, and taking my splash guards off to put on my skid plate, in heavy rain, my belt I guess gets wet, slips and I lose power steering. I can hear it screech.
I didn't think that would be the case for snow, but sure enough after plowing through my driveway to go to work it was slipping screeching and loss of power.
View 7 Replies
The power steering seems to work fine and dandy. But when I turn the wheel all the way to the right, or to the left, the serpentine belt squeals, indicating that the power steering seems to have faulty valve or whatever. What is causing this problem?
View 6 Replies
The AC/power steering belt in my 2004 Santa Fe, 2.4L has intermittently squealed for some time, but lately the squeal has gotten louder. Initially it only happened when the compressor was on, but now it happens when the compressor is off. I have not experienced a loss in steering power but I did notice that the power steering fluid appears to be discolored. I have replaced the belt and re-tensioned it several times hoping this would solve the issue, but it hasn't. I intend to take the belt off again and see if the pulleys all spin freely. When I replaced the belt initially, everything did spin freely. My guess is that the power steering pump may be shot and is putting excessive load on the belt, however, there is no PS pump "whine" and again, no loss of power steering. It looks like I should also check for separated pulleys.
View 3 Replies
I have a 2005 Elantra GLS. I've noticed that anytime it rains or I hit a puddle, my belt squeaks and sometimes it almost sounds like it's grinding and I lose power for 4-5 seconds. From the front passenger wheel well, I can clearly see the belt. I noticed there are holes drilled into the frame, and I was wondering if there is suppose to be a guard there to prevent water from getting on the belt?
View 2 Replies
I have a 2003 Santa Fe, 2.4L.
Last night, I added some power steering stop leak to my PS system, but I accidentally spilled some below the reservoir. Soon after, that area of the engine starting making a consistent "spark"-type noise. I think it has something to do with the belt, because when I turn on AC, the noise gets a little faster in rhythm.
I say "spark" noise because it sounds like an electrical spark, rather than clicking or whining.
View 3 Replies
MY 2003 Santa Fe is fwd with the 3.5 v6. While under normal conditions, the engine lost power and began "chugging" and "bucking". There was also a belt slipping "whine" associated with this problem. The problem continued for about two minutes, then corrected itself, and I was able to drive normally.
View 1 Replies
A few days ago, my car developed a loud squeeling noise coming from the belts. I opened the hood to find both caked on and still wet PS fluid all over the left side of the engine compartment and the belts/pulleys. Most of the mess was concentrated near the PS fluid reservoir and the two hoses attached to it (picture of hoses and reservoir below from Google). This leads me to believe there is a leak in one, or both of these suction hoses. I will replace the hoses but my question is how should I clean up the fluid on the belts and pulleys? Should I use a soft brush and a rag with soapy warm water, brake cleaner and/or engine degreaser to get all the gunk off? I would really loathe having to have to put in new belts, seeing as that I just had all the belts changed 6 months ago. This squeeling noise makes my car sound like some old junky clunker and I hate it.
View 2 Replies
How to diagnose bad suspension components on my own. Basically, what's going on right now is sometimes when taking a left turn, i feel a vibration and sometimes feels like one of the tires are slipping underneath me. at speeds above 30 mph, there is a reverberation noise, and above 60, my car starts shaking and I begin to lose it's handling properties. Occasionally when going over bumps, I hear a slight knock coming from the right front. Also, I'm having elevated cabin noise. The tires (at the moment) still are wearing evenly. I believe this is a wheel bearing, as I test drove a focus once where the seller said it had a bad wheel bearing and it's having similar issues. Would I most likely be right, or could there be another issue?
View 5 Replies
I have an 02 Elantra GT. I was dropping off a friend who knows cars and went to turn around, turned the wheel to full lock to make the turn and heard a squeal. I asked my friend what it was and he said it was the P/S and I just needed to add some P/S fluid. I got some fluid and sure enough when I went to fill up the reservoir it was below to MIN line, not too much below but still below it. I filled up the fluid and didn't hear the problem for the rest of the day but this morning I heard the same noise when I was leaving for work. I figured the fluid had to work its way though but am not sure if there is something else I should check or do.
View 3 Replies
My power steering seems to have sprung a leak. There is quite a bit of fluid below the passenger side of the steering rack. The leak seems to be right below where the power steering hose comes down off the pump, gets secured to the chassis and changes to metal line from rubber. The metal line then goes into an L bend and is routed towards the driver side right where the leak apparently is.
I haven't had a chance to have a good look, as it was 10:30 at night when I parked it and looked (12km of careful city driving since it started to act up)
Is this a high pressure or return line?
The leak seems to be forward of the steering rack, so hopefully I wont have to replace it.
View 8 Replies
I have an 01 Hyundai Elantra that has had power steering problems for awhile.
Awhile back, when we would fire it up, we'd get a loud screech. Eventually, my father in law replaced the power steering pump and belt.
Now there is a new issue. Ever since he has replaced that, on start up, there's a small screech and when turning out of a parking space, the steering wheel is tough as if the power steering isn't working.
I was thinking it's the power steering pump pulley, but can't seem to find any real stores that just sell the pulley itself. I did see the pulley have a minor wobble in it when examining it. Thinking maybe its the bearings on the pulley.
View 2 Replies
I am searching for any kind of adjustment that might enable me to force the clutch level to the positive stop. It stands off about an 1/8" to 3/16" and I think is the reason I am not getting engagement in first gear, it slips heavily but fine in all other gears. The key way on the the lever prevents me from moving it a notch or two if I thought I could and don't know if that's even the answer . I can't figure out what is preventing it from returning fully on its own I can push it by and and a little fluid will squirt from the reservoir. Ive replaced the slave cylinder and bled it.
Is there any adjustment under the dash? This is a 2001 elantra that I just put a 2000 trans 5 speed.
My original plan was to pull the parts from the 2000 and replace in the 2001. I had lost 1st and 5th totally and found a 2000 that went right in with some minor mtr mnt mods. It shifts just fine except for this 1st gear thing. I saw a video and am having second thought about that move. I dont really want to pull the trans out again.
1st gear just keep slipping. new clutch kit installed when I swapped them out. It feels like a linkage thing somewhat but I cant find adjust ment to tryout.
View 4 Replies
My 2002 Elantra (about 276,000km) had some kind of leak in a power steering return line. A mechanic looked at it, said I needed to order the replacement part from Hyundai. Got the part, the mechanic (not Hyundai) took 2 hours and fixed the line.
Driving away from the mechanic, I noticed the front right turn signal was blinking abnormally rapidly. Left turn signal is fine. I call the mechanic, tell him what's happening, and ask if it might be related to the power steering line fix (after all, they're both in the right front side of the vehicle). He swears up and down he touched nothing having to do with the turn signal.
Okay, maybe it's just a coincidence. I buy a new signal light and put it in. Same thing with the front right turn signal blinking too rapidly. While driving back from replacing the bulb, a car cut in front of me and I went to lay on the horn....nothing happened!! No sound. To top it off, for a while now, the dashboard lighting has been dimming slightly at certain times.
What could be causing all this? The alternator is fine, someone tested it.
View 4 Replies
My 2004 Santa fe speedometer is acting erratic almost all of the time , sometimes it works right. I have replaced on sensor that is easy to get too, right below the air filter and the other is below the cable, but the hard part is that in order to remove the 2 bolts holding the cable in place part of the frame or steering apparatus is partially blocking the bolt where a socket will not fit over...
View 2 Replies
I replaced my GF's water pump, timing belt, tensioner and roller on her 05 Elantra. WHen I started the car up I can hear a loud whine from the belt.
Everwhere I searched I read that it's too tight.
But in this video: [URL] ....
At around 9:11, when the guy starts the car it's the same exact whine? Is this normal or something with a brand new belt? Or did he tighten it too much? Or is it because her timing belt covers are missing the rubber grommets, and there is a HOLE in the side of one of them. So am i getting the full brunt force of the timing belt?
View 2 Replies
Changed the timing belt. Used the red mark up top and the cut in the block on the lower one to get TDC. Changed everything with new parts. Double checked the marks after the belts were on (rotated by hand through two full turns and checked to see if the marks were in the same spot). I followed the write up that was posted here by U95.
Anyway, the car won't start. It tries cranking, but won't actually start. There is fuel and the battery should be good to go. There shouldn't be any Fuel/Compression/Air issues.
I guess my question is: If the timing belt is not tightened enough, would that keep it from firing?
Also, in trying to crank it by key every thing sounds normal (no knocks or pings or valves getting bent sounds) and turning by hand gives just the little bit or normal resistance but spins nicely.
I'll probably take the battery to get it load (I used my tender to try and start it as well, didn't make a difference) tested tomorrow and then try the starter (shouldn't be bad though, only 60k on the car). Otherwise I'll have to teardown and start over.
View 13 Replies
2003 elantra when I start the car the belts squeal for about a minute, then whatever I do they start squealing again- turn on headlights, roll down windows, steer the car, turn on ac, anything starts the squealing again. I have had all new belts including timing belt, water pump, etc and it is only getting worse by the day.
View 2 Replies
I recently replaced the timing belt, tensioner, and roller in my car. Today I became concerned that I hadn't tightened the tensioner properly so I did a quick check (it was). I also noticed the timing belt felt a bit loose, so I tightened it to what I thought was about 1/4" deflection with 5lbs pressure—not what that feels like in that tight space.
When I started the car there was a noticeable whining sound. Before I changed the belt there was a slight whining sound (but there was no whine after I changed the belt). So I loosened the belt a bit and there's now a slight whine. I feel like the whine shouldn't be there but it's hard for me to imagine that the belt should be any looser since I can move it 1/4" inch without much effort.
So, should I be tightening the belt to the point where the whining is gone, or is a slight whine ok?
View 2 Replies
I just changed the timing belt on my sisters car and finished yesterday and drove it today. A check engine light came on so I went to check it out and P0016 popped up. I've done some research and people say that it might be that the timing belt is misaligned or loose. I tightened the belt not too tight but not too loose. Note: I also spilled coolant on the crankshaft pulley and a bit on the belt itself. The car idles rough when driving too. I will tomorrow take off the cover and check the tension of the belt.
View 9 Replies
2003 Hyundai Elantra.
Driving on the highway and thought I heard a belt squeal. Looked at temp gauge, overheating in the red. Stopped car. Antifreeze on passenger side sprayed around, hard to tell from where.
Waiting a while, put a good amount of water in it as there seemed to be no anti-freeze left. Drove a bit more and it started going up on temp gauge. Pulled off highway on an exit, temp gauge went back down before I could pull over.
So I continued on the highway. The temp gauge would go back up to 3/4, then I'd put it in neutral to cost to a better place to stop, and the gauge would go back to halfway.. continued this for several miles to get home. Never overheated again, but kept getting "hot"(3/4) and dropping back down to normal (1/2)...
View 4 Replies
