Elantra XD (2001-06) :: Noise When Engage A Gear
Sep 2, 2015
Just wondering to diagnose the noise my manual 2002 is making when I engage a gear.
Generally, it'll clank every single time I put the gear in gear. I.e. clutch down (quiet), shift into gear (clank), lift clutch up (clank).
Very annoying; has been happening basically since I bought the car (but obviously not when I test drove it!)
I do not think it's a motor mount, especially since I wouldn't think that moving the gear into gear (before lifting clutch back up) would cause the motor to shift enough to make the mount clank. If at all...
Anyway, here is a link to a YouTube video I've uploaded. Every time you hear a clank, I'm simply lifting the clutch to engage the gear. I do this quite a few times going forward and backward. [URL] .....
View 3 Replies
Advertisement
Our 2002 Elantra (automatic, 57000k) seems to have a blown transmission. A few days ago, it sounded like the car was "whining" and then it was having difficult time engaging next gear and eventually check engine came on and the car stalled. Firestone said it's a transmission problem.
We've had the car for less than 10 years so technically this should be covered under their powertrain warranty but I have a strong suspicion that the dealership will find a reason to not honor the warranty. It's still below 60k miles so we really didn't have to replace transmission oil.
View 5 Replies
My car has been making this grinding noise for the last 2 months. It happens when I put the car in reverse gear and slowly release the clutch. Rarely happens also in 1st and 2nd and 3rd and is always at the beginning of the transition when I am letting the clutch go. I do not know if it is the transmission, the clutch or any other part. I drive a 2002 Hyundai Elantra 5 speed manual transmission with over 120 k miles
Here is a link to a video I posted so you can hear the noise it makes : [URL] ....
View 19 Replies
My cruise control wouldn't engage this afternoon and once I got home I noticed that the brake lights including the third light are on. Headlight switch is rotated to off position, checked brake fluid and its normal, backed car up and hit pedal thinking something might have been locked up but to no avail.
View 4 Replies
I recently bought a volkswagen jetta 1.8t wolfsburg edition 5speed. While driving i switched from third into fourth gear upon letting the clutch completely out the rpms began to spike and no power was being produced. So I neutralized to the nearest stop and tried shutting my car off and restarting it and then putting it into gear it would not engage in any gear what so ever at all. The clutch then had no pressure or resistance in it when pressing down and lets up slowly.
The motor stilll runs perfectly fine and the actual shifter will move into gears in the gear box but the clutch still has no pressure and doesn't even attempt to catch or engage in any gear. Do i just need to replace the clutch or the intake or the flywheel or what? In addition i have since ran the code runner and nothing comes up besides the intake code but that's because i took the intake off to manually try and engage the clutch into gear witch still did not work.
View 2 Replies
Alright so I've had this car for about six months now and the clutch was supposedly replaced by the dealer I got it at. The clutch usually grabs about half way up but sometimes it's higher. I replaced the master cylinder because it blew out, when changing my I take I noticed the slave was starting to leak so I replaced that about three weeks ago. Ever since then, the clutch seems to grab differently and seems to be taking longer to engage.
Now, I did the "slave mod" on the old one AND the new one so it's not that. Do you guys think the new slave is bad? I have high temp dot 3 in there (I try to only use the best fluids for my cars). It just doesn't seem to grab as hard as she used to. Like it takes a bit longer to engage. The clutch (should) only have 15k miles on it. The clutch parts are under warranty but I'd still have to pay for labor since it's a wear part. I'd like to avoid replacing it if it's that new u less it's definitely going.
View 9 Replies
The problem started with a front seal leak a few months ago which I had no choice but to continue driving with because of low funds. I don't drive much so a couple of quarts of ATF was usually enough to get me out and about for what little driving I had to do. I know.. a front seal is cheap, but I'm partially disabled and unable to work on anything that is not under the hood.
I finally scraped up enough money to hire a friend to replace the seal, but he had a life crisis before completing the work, so I had to get another friend to reinstall the trany... still had the leak, but I could get around by adding ATF as before.
So we tried again... dropped everything and put another new seal on. This stopped the leak, but we got some grinding/squealing noises and could not get the trany to engage any gear.
From reading forum posts and other sources, we decided to replace the TC which we just completed this evening. We got some more of the grinding / squealing noise like before, except that it only occurred the first time we tried cranking the engine, the 2nd time we got no noises, but again no gears engaging.
What to check/replace next assuming there is something we can look at other than a total trany rebuild or replacement. I personally find it hard to believe we could have gone from a tolerably functional trany to scrap metal just replacing a seal and the TC. Its gotta be something simple we overlooked !!
View 9 Replies
My 2006 Elantra (54,000 miles) shifts really, really hard when it's not cold and passes through the 35 mph range -- hard enough to make you glad you've got your seatbelt on. I've taken it to my regular mechanic and now it's in an automatic transmission shop.
My mechanic changed the fluid (twice), and took it through a "learning sequence". The fluid didn't look that bad and he reported that there were no codes to work with. He thinks I'm going to have to get a new transmission.
The AT shop has confirmed that there are no codes to work with and that the problem begins at 143 degrees. They tell me that the transmission is shifting into a higher gear without releasing the lower gear. They tried replacing a couple of solenoids, but that yielded no change in behavior. Now, they're telling me they "think" I need a new computer. I'm just afraid the trial & error approach is going to cost me a boat-load.
View 1 Replies
I have a brand new (2 months old) 2011 Subaru Forester 2.5x that has a 4 cyl engine and a 5 speed manual transmission. This past week it's been cold here in New Hampshire and in the morning when I first drive the car, I have trouble shifting from 1st to second gear. When I shift from 1st to 2nd, I hear/feel some grinding noise as I try to engage 2nd gear. This only seems to happen when the car has been sitting around in the cold for a long period of time. Our garage has been cold (34 deg this AM) for the past week and when I drive out of our driveway and on our street I encounter this problem.
Normally, this problem only happens the first time you shift out of first and into 2nd. However, the other day, when it was very cold (5 degrees out) it happened several times as I drove down the street. After it happened the first time that morning, I stopped the car and drove from a dead stop, shifting from 1st to 2nd. I had problems 3 or 4 times trying to shift to 2nd. I ended up double clutching the car to avoid making the grinding sound. I took the car to the dealer. The couldn't repeat it but I didn't expect it to, because the car was warmed up and it was warmer during the day (low 30's by the time I got to the dealer that afternoon). The mechanic changed the transmission oil and checked the magnet in the pan to see if there were any metal pieces. He did not find any metal pieces. That was two days ago.
Unfortunately, every morning since then the car has had the same problem. Once the transmission has been warmed up it runs flawlessly and I have no problems shifting. I've made sure I am fully depressing the clutch for each shift. The past few days I've been taking the car out on an early morning test run and like clockwork, it has problems on the first shift into second, and it usually works fine after that. I have an appointment next week to leave the car with the dealer overnight. They will test drive it to see if they can reproduce the problem. What might be wrong? I have a workaround solution to avoid grinding the gears. I simply double clutch shift into 2nd for the first few times that I shift after the car has been sitting in the cold for a while. However, this is less than ideal for a brand new car.
View 9 Replies
My grandma had purchased an almost brand new B6 Passat with the 4-motion VR6 all leather interior with about 8k on the odometer. Recently she has had some problems with it and has asked me what is going on, My dad has an Audi Allroad, my mom has a 01 A4 event and I have a 04 GLI so we know some stuff about the cars but these problems are eluding me and I was going to look for some counseling. First, her front tires are making this horrible sound, she says it sounds like a Mack truck and it gets worse as you go faster. I'm thinking its the tires but why would it be like that only after 8k? The second problem is her transmission, she has had the transmission fail to engage into gear 3 times, where it takes about 2-10 seconds before it engages. Now the car has about 10k on it. [URL]....
View 11 Replies
I have a Hyundai elantra 2002 that is stuck in second gear. I was driving it, I came to a stop sign so I put it in neutral and when I shifted into first i heard a pop. I started driving and when I shifted into second I noticed the shifter was really loose, when I tried shifting into third I couldn't.. it is like there is a brick wall. I can shift from 1st to 2nd but the shifter just moves up and down. Also if I let the clutch up it stalls the car. I was told that my car is stuck in second gear.
View 1 Replies
I have a 2005 5 speed manual elantra that I let my wife drive it home when I drove another vehicle and the next day when I went to drive it it started grinding going into second gear. What can be causing this? The clutch works great on the other gears.
View 1 Replies
My 98 elantra will not shift out of 2nd gear?...
View 4 Replies
I engage my 4wd all the time to keep it working and lubed up. tonight i turned it on and it was making a light clicking noise like a card in the spokes of a bike (not loud) and there was no vibrations or nothing that really sounded bad..what could be making this noise, what should I look for...
View 5 Replies
I recently started getting transmission problems with my 2001 elantra.. the car would slam into second gear and the check engine light would come on and it get stuck in 3rd gear.. The codes I am getting are P0720, P0715, P1529. I searched and i found that most people that had this problem replaced the input and the output speed sensor and the problem is fixed.. so i went and i got two new sensors and replaced them i am still have the same exact problem... the car drives good for the first 5mins and then it would slam hard into gear, check engine light comes on the it get stuck in third gear...
View 6 Replies
I bought my 2005 automatic 4 speed Elantra knowing of this problem and feeling good about being able to track it down. how ever This did not stand to be the case. Start up cold shifts through every gear smooth as silk with know slippage or harsh shifts. roughly 10 to 15 mins after the car reaches operating temp on the gauge it begins to slam into 3rd gear only. Most of the time it is a double slam. Like bam bam real fast but indeed does shift into the 3rd gear then into over drive smoothly. I can duplicate it any time i desire to by merely pulling it back into 2nd gear and manually pushing the shifter back up to 3rd. it will slam every time with out fail. The man i bought it from told me he had this trouble and changed the transmission out with a 500.00 used one and did the exact same thing...
So I felt must be electrical wiring or TCM bad but upon examination i found no codes present to date. he threw parts at it and replaced both input and output sensors based off some thing he read on the net. also he said he replaced the TPS with a TPS from a wrecked car, still same harsh shift. he however could not remember how the fluid looked upon changing it and the filter as he also did that, nor can he remember what fluid type he used. I know shot in the dark right??? What is the actually fix such a hard slam when shifting into 3rd.
View 3 Replies
2001 Hyundai Elantra 183 miles.
codes- p0720 output speed sensor circuit malfunction, p0500 veh speed sensor a malfunction.
Recent fixes on my 2001 Hyundai Elantra.
A few months ago i had my speed sensor cleaned, and a power steering leak. No problem after that was fixed and cleaned the sensor. Soon after that my water pump went bad and i had that replaced along with 3 new belts. Just last week i had my front driver side replaced with a new wheel bearing and axle.
My Problem then and now.
My problem months ago, my car would be shifting into different gears as it pleased; while driving or sitting at a light i would feel it jump and it felt as if it was stuck into 2nd or 3rd gear as i was driving. My engine light would soon come on after this. To accelerate i feel as if i had to floor my pedal when the shifting or engine light came on. I looked up my codes and they are the same as they are now. I read about same problem and fixed it by just cleaning the speed sensor off. My friend and i did the same thing and it fixed those issues. My problem now is that i just had my axle and wheel bearing fixed (my car moves smoother and quiet) my engine light came on again, it had not been on since, i read the codes and they are my speed sensor same as before but my car has not been shifting as it was in the past. Would this be because the sensor needs to be cleaned again or replaced, or because of my new replacements on my wheel.
View 1 Replies
Our Hyundai Elantra starts up and idols like a dream, but when you put it in gear the engine misses so bad it doesn't want to go. What could be the problem that is causing it to do this?
View 5 Replies
In my 2005 elantra GT 5 speed, I get a weird pulsating vibration in 5th gear at 45-50mph. It's noticeable enough to have a friend ask me about it. But it's very slight. I have 124k miles, and a new clutch. I've only had the car for a couple weeks so it's still new to me. My first inclination is axles or a wheel bearing. Maybe a motor mount. But then again, only in 5th?
View 3 Replies
I've hyundai elantra 2013 while changing gear by car jerk and sometime it doesn't jerk. What is issue causing car to jerk when changing gear. It happens not every time, sometime it don't jerk while changing gear.
View 1 Replies
I am desperately trying to work out what may be going on with my Elantra GL 1.8 Auto (Australia).
The car gear changes are temperamental and every now and then it thud's and it feels like there's only one gear.
This is a video (about 5min long) of what happens when it's playing up, towards the end of the video is where i restart the car and it works absolutely perfectly. [URL] .....
Don't know if it's worth noting, but when the car is in it's funny gear shift phase, the central locking works intermittently and the electric windows go slower than normal....
View 4 Replies
