Elantra XD (2001-06) :: Knocking When Turning / Vibration At Higher Speeds
Apr 16, 2015
Recently when I was on a longer distance drive (multiple hours) my car was producing an unusual vibration. It seemed to go away after some time. At the end of my drive I was turning left around a bend and there was knocking sound. One of the boots on the cv joint has been leaking grease so I went ahead and replaced both cv axels.
The knocking is still there. Here are the symptoms:
- Knocking sound when turning left when the accelerator is down.
- Knocking sound is somewhat intermittent when turning, not always continuous.
- The vibration is not always there and is only there at higher speeds, and is made worse when accelerating.
- All of this appears to get worse the longer the car is driven (heat?).
View 3 Replies
Advertisement
I have two simultaneous problems with my 2005 Elantra (automatic transmission). I don't know if the problems are related or not, or if they are alarming or not.
Background on the car: timing belt and water pump replaced in 2010; four tires new in 2010; oil changes every 5000 km.
The first is that my engine is making this 'whirring' sound when I approach 80km/hr. It's not high-pitched, but more of a droning noise. Having read around the forums, I see that Elantras commonly make funny engine noise, but this is fairly new to my car (145,000 kms) and definitely not there at all when idling or at low, city-street speeds.
Additionally, I have a weird vibrating noise coming from the front left of the car only when I am dead stopped and the brakes are fully depressed. It doesn't make this sound in park, and I don't hear it until the car has come to a complete stop; there is no odd noise while slowing down.
View 1 Replies
But i still have the sound, and it definitely sounds like its coming from the passenger side, however when i looked at everything and tried wiggling the wheel, nothing seemed out of place. Would that still indicate a bad ball joint? Is there anything else i should inspect/have inspected?
The sound only happens when i go over a big bump, or a medium bump at a higher speed. It doesn't seem to affect my steering or driving feel, but its still not a noise that should be there.
I found that the driver side tie rod was a little loose, and replaced that, but sound persists.
View 3 Replies
I've owned this vehicle for the past year. This 2009 Corolla XRS manual has a very annoying steering rattle which took me the whole year to finally breakdown and diagnose. There are many forums stating this rattle is associated with the intermediate shaft assembly #2. I did end up replacing this part 45260-02110, hoping this would fix the rattling or knocking issue. It did not, but smoothness the steering has improved. I removed the upper portion of the intermediate shaft to pinpoint the sound. Originally I believed the noise may have been coming through the bulkhead from the intermediate shaft #1 or steering rack. I checked under the boot and everything was snug. Then I rattled the steering wheel around and this what I found.
It seems the noise is coming from the pinion where the power steering motor meets the steering column. You can hear the knocking noise with settle steering wheel movements. As I move faster, the knock turns into a rattle at higher speeds most likely vibration from the road. At this time, I do not want to disassemble the whole column just to see if I can adjust the motor height (if possible).
YouTube : [URL] ......
View 6 Replies
2003 7.3 Excursion, 130k, stock suspension with newer bushings, etc.
Vibration when braking at higher speeds - not felt as pulses through brake pedal or shimmy through steering wheel - rather, a "body" vibration. Stops as soon as the TC unlocks. Being a diesel I can't tap the brake to allow it to unlock like on the gasser 4R100's - its locked until it shifts down into 3rd. Turning off OD puts it into 3rd but locks TC (no way to "single out" TC). Only felt when braking in OD (though I haven't tried running up to highway speeds with OD off/trans in 3rd) - braking is completely smooth at all other times/gears/speeds and at all braking force (light, mod, heavy).
Front and rear pads are good with even wear and sufficient material, lugs evenly torqued, tires good/balanced, no sign of a stuck caliper or rotor warping, MM manual hubs unlocked. No driveshaft carrier on the Ex's, just a regular two joint shaft with recent Neapco Gold u-joints, no slip yoke play. Trans filter replaced 4k miles ago, 6 +/- qts DexIII/Merc exchanged when I did the filter, fluid smelt and looked fine. Transfer case fluid changed about 5k miles ago. Factory LSD rear diff not serviced recently but fluid suctioned from fill hole looks acceptable.
I'm afraid that something is going on with torque converter/shudder but I don't get any shudder or slip under acceleration or at any other time and gear shifts are smooth. I know that the 4R100's can be sketchy, especially with 130k, but want to get suggestions before digging into it. I've also got a very slow hydroboost leak/weep but the power steering fluid is properly filled. Steering is smooth and proper, brake pedal movement is normal so I assume there is no air in the lines.
View 14 Replies
I've been hearing a faint but rapid ticking noise when taking faster exit/clover-leaft style turns (usually ~40mph). I think it's the ABS or traction control on the verge of kicking in because if I push it a little harder I do get the flashing traction control light on the dash, but the ticking is happening before that light comes on.
I'll ask the dealer when I do the courtesy 30 day inspection... I'm at the end of the 2nd week of ownership with 200 miles right now, so I'm still getting used to the car. (2013 Passat TDI SEL). Loving the 40+ mpg on my rush hour commute!
I did a search and didn't find anything on the B7 forum that might explain this noise. I don't think it's a CV joint since the car is new, it happens when going around these style turns either way and only seems to happen at higher speeds. I suspect it's just that the traction control is sensitive (or maybe I haven't scrubbed the tires enough yet to get good contact).
View 5 Replies
Ok so we all know it's usually warped rotors or possibly a caliber problem. But let's say u have new of both. And still I'm getting a wobble, not only when I brake at higher speeds, but when I'm on certain roads. Only certain roads. Say about 20% of other roads while driving I get a slight wobble. Not too bad, but a very annoying wobble. I bought this CTS at 35k and now has 45k on it. And again I bought this car for my long commute and a smooth drive. Which I'm not getting. I can't take it anymore! I've got to figure this out. Getting a wobble in the steering while on super smooth roads. And I know it's the car because I have a Chevy Cavalier and a Dodge truck in the family that don't wobble on the same roads.
View 16 Replies
My husband and I noticed that my Hyundai Elantra (2007) sounded rough when running over 60mph. The car has 61,000 miles on it and is due for an oil change, a radiator flush, and a fuel filter replacement. My manual says that the platinum coated (versus iridium coated) spark plugs would need to be replaced at 60K miles. I was told that the car would run rough at lower speeds if it was the spark plugs.
View 7 Replies
Today was the first day I drove my Elantra on the interstate with the sunroof open. When I was cruising at 65-70mph, I kept hearing a noise that I thought was coming from another car. It sort of sounded like a popping or thumping noise. After a few minutes, I reached my hand up and noticed the sound was coming from the metal bar that rises up a little at the front of the opening when the glass slides back. The wind was vibrating it and making it flap in the wind.
View 2 Replies
I recently started hearing a pop/knocking noise when I'm turning at low speeds (0-10mp) only. I've already done a search but most of what I found dealt with installing new springs and/or coilovers. The thing is, I only started hearing it a day or two after I installed my rear sway bar. I've gone under a couple if times to readjust the sway and put it back on thinking I might have torqued it too tight or too loose. After I did that, the noise would go away for about a few days but then it comes back again?
View 1 Replies
My engine keeps knocking for a minute or so after I come to a stop and turn off ignition. Should I be concerned?
View 14 Replies
I have a 2013 Elantra, owned since new... I recently started hearing a knocking sound coming from both front wheels while turning in reverse. I have yet to take my car in to have it looked at, if I can do it myself I will but I'm not sure where to start.
View 3 Replies
I just bought a 2008 LS600 Obsidian with Exec package. Happy with the car except for some steering vibration at low speeds when turning. Took it to Newport Lexus...they say..."normal for an AWD LS600".
View 11 Replies
It is a '90 Nissan Maxima. I just replaced my drivers side axle (cv joint was clicking), and now my car vibrates at highway speeds when turning right. I am pretty sure I seated the axle correctly....could it be a bad axle? I heard that turning the axle 90 degrees and reinstalling may work? I got a new axle (Empi brand).
View 2 Replies
I have a 2007 elantra. I drove it for a while, then my ma needed a car (her tercel was a little unsafe) so I traded her. She loves the car, but as sometimes is the case, her dealer is not very nice. She has a severe side to side knocking noise in the steering- can be easily duplicated by sitting with the car idling and turning the wheel back and forth, even a little. Doesn't correspond with driving over bumps unless the wheel is inadvertently turned by the bump. If the suspension is unloaded (front wheels off the ground), noise disappears. No EPS lights, no codes in any system.
Listened with a stethoscope inside the car- not that loud through column within car. Inner and outer tie rods are tight, noise is not heard loudly with stethoscope through struts, upper mounts, lower arms. Under the car with loaded suspension (rhino ramps), noise is deafening in the rack, with a stethoscope. Dealer told her it needs a steering rack, I definitely understand why they would say that as the noise is clearly audible through the aluminum housing directly below the entrance of the column shaft into the rack. Only TSB I found was for a worm shaft flexible coupling, but the TSB says this is bump related.
View 7 Replies
Sometimes I will stop at a light and my idling rpm will go from 600 (usual rate she idles at) to about 950. While this may seem inconsequential in the grand scheme of things, it's noticeable enough that it seems like the car wants to go. It'll lead me to depress the brake more. You can also hear the higher pitch of the faster turning engine (it is a 50% increase in speed). This will happen at random times so I have not been able to pinpoint if it is caused by a particular driving style. ECM for this?
View 7 Replies
So my girlfriend has an 04 elantra 2.0... the car will be running fine but then after so long of driving(maybe 15, 20mins) itll start acting strange..
It will hesitate to accelerate and shift hard and at higher rpms. Then at cruising speed it will turn off instantly(no sputter, hesitation, almost as if you just turned the key off). Seconds later the engine will come back but the gauges die and the engine will remain on.
At that point i pulled over and as i was on the brakes the car died when I came to a complete stop. Once the car completely turned off it would not start back up. However jump starting it got it going. The car is not throwing any codes.
View 1 Replies
Ok I changed the 2 front struts on my Santa Fe. And the strut mounts. Rides alot better and no shimmy in the wheel but I noticed a knocking noise when turning the wheel sharp. What I have come to find out the top of the spring it turning the whole cup or top hat it sits in. I put the cup in the right spot because there is a flat spot on the thread of the the strut.
View 13 Replies
There is a knocking sound when turning my steering wheel back and forth, and when driving around. It started over the past few days. I used my stethoscope and it seems to be coming from the inside end of the tie rod, although it was very difficult to pinpoint.
The thing that really confuses me about this is that the knocking sound was happening two months ago and I replaced both control arms and the knocking went away completely. It came back a couple of days ago. I checked the tightness of the nuts on the ball joint and tie rod end.
View 6 Replies
I have a 2001 excursion limo with 108,000 its a v-10 2 wheel drive with stock wheels and tires. I believe both my front hub bearings are going out, I am hearing some grinding at slower speeds and while turning, but seems to be ok at highway speeds...Anyway I think I am going to replace both front hub bearing assemblies.
View 12 Replies
2004 Elantra sedan 2.0 ... When engine is started oil pressure light comes on an engine is knocking. Light goes out and knocking stops until you accelerate to a shift point. is it time to replace the engine. Oil is full. 144,000 miles
View 1 Replies
