Elantra XD (2001-06) :: Hesitate To Accelerate / Shift Hard And At Higher RPMs
Jul 13, 2015
So my girlfriend has an 04 elantra 2.0... the car will be running fine but then after so long of driving(maybe 15, 20mins) itll start acting strange..
It will hesitate to accelerate and shift hard and at higher rpms. Then at cruising speed it will turn off instantly(no sputter, hesitation, almost as if you just turned the key off). Seconds later the engine will come back but the gauges die and the engine will remain on.
At that point i pulled over and as i was on the brakes the car died when I came to a complete stop. Once the car completely turned off it would not start back up. However jump starting it got it going. The car is not throwing any codes.
View 1 Replies
Advertisement
I have an 01 Elantra Gls with perplexing issues. The car starts at 3000 rpms, and continues to bounce between 2k and 3.5k in both park and neutral. when I put it in reverse i get a very hard shift. It actually jerks the whole car. in drive and reverse, it idles around 1.5k it hesitates quite a bit to accelerate. All fluid levels are right and don't smell burnt. it takes me 10 mins to put 4 gallons of gas in. if i pump too fast it shoots back at me. i randomly smell gas while driving. Im hoping these problems are a couple of issue I can handle at home. i just wanted some input before i buy the manual. thinking vacuum lines maf sensor.
View 7 Replies
2013 Elantra GT ... Odd sound when shifts at higher RPMs. Like a chirp, or a tiny blow off valve from an old home turboed civic. Some sort of leak? When the engine is under load, it sounds like I may have some sort of minor exhaust leak, though that is nowhere near audible in the video. Very curious as to what this is.
[URL] ...
Listen right at 0:14 when it shifts.
View 20 Replies
I have manual shift and the clutch is worn out. when in motion if I press the pedal the rpms jump but the car does not accelerate. only way to accelerate is to press very gently.
Q: do I always need to change the flywheel, which is expensive or changing just the clutch will do??
View 12 Replies
My 2004 Elantra occasionally won't start. When I hold the ignition on Start, the radio loses power (but the dashboard doesn't) and nothing else happens. Sometimes, tapping the gas pedal will suddenly cause the car to start. Once, I had to stomp the pedal to the floor before it would work.
I just replaced the battery (and positive cable end since it was corroded in place) and recently replaced the spark plugs (which were badly burnt). There is a check engine code for "catalyst underperforming" which seems unrelated.
I suspect my car has fuel delivery problems. It occasionally sputters while idling and often has power loss while driving if I try to accelerate hard. It seems to have trouble shifting into 4th gear from 3rd or 5th, but that may be another issue entirely.
What I should check to diagnose this, or replace to resolve it?
View 7 Replies
The car is an '05 elantra, 97,000 miles, auto., car is new to me. First time on the freeway today, 30 miles @75-85 mph, at the end of the off ramp I could feel it surging, shift to neutral rpm's went to 1500, hoss the gas and back to normal. On the return trip off ramp, went to neutral, jab the gas, everything OK. I'm going to clean the throttle blade, check things, etc.
View 3 Replies
I drive a 2001 Toyota Camry LE, 2.2 4 cylinder. It has about 206k miles on it… About 2 months ago I started to feel slight hesitation when I was driving…. It was so slight I wasn’t sure if it was happening or not. Recently the hesitation has become much worse… typically it will hesitate and jerk when I try to accelerate from slow speeds… this primarily happens when the car is cold. It will also jerk and hesitate when I am cruising at a fixed speed. If I step on the gas, the jerking stops.
Here are known issues and recent work I have had done… in November I replaced my complete exhaust system myself, including the downstream oxygen sensor. The cat is now bad and it will rattle. I had a mechanic replace my water pump, timing belt and all pulleys and tensioners associated with it about 2 weeks ago. The hesitation predated this problem.
About 5 years ago I replaced my own plugs and wires… when I did this; I noticed oil on one plug. This was for the cylinder closest to the driver’s side. I never noticed any issues with the performance of my car related to the oil, and I do not burn through much… perhaps a quart every 2 months. About a week ago I replaced my plugs and noticed the oil again. I do not know if this relates to my hesitation problem or not. I also filled my tank and used a container of injector cleaner, thinking perhaps a clogged injector was causing the problem.
The problem still exists.
Now I am thinking it might be one of two problems… either a defective ignition coil or a bad throttle position sensor. Yesterday I borrowed a code reader… it told me I had “long fuel trim in bank 1”.
View 8 Replies
I have a 2001 Elantra GLS, 160,000 miles. These two codes come up on ny diagnostic tool.
P0422
Main catalyst efficiency below threshold (bank 1)
No symptoms at all
P1529
Customer snapshot request
Symptoms
Car will shift hard into third gear and stay there without shifting at all regardless of speed. Shutting the car off and restarting will sometimes fix, but only temporary. When car runs normal, it runs fine and shifts good. At speeds around 40 it seems to kick back and forth between 3rd and overdrive as if it can't decide where to be. Tried replacing speed sensor, but new sensor did not fix problem.
Fuel Sys 1 CL
Fuel Sys 2 NA
Calc Load 18.4
ECT 201
STFT B1 0.0
LTFT B1 -2.3
MAP 8.6
Eng RPM 3351
Veh Speed 22
EV flashing
O flashing
View 17 Replies
The other day I noticed the car slipped into reverse fairly hard, then when I placed it into drive it also slipped in fairly hard. Once I was out on the road it hesitated and then slipped into gear 3rd then 4th, and when I slowed down it seem to hesitate when gearing down. Two days passed and no problems, then today started up again, and now the "check engine" light came on...! Shifted ok on the way home this evening but check engine light still on. Only 34K, 2012 bought in June 2011. Has been an absolutely brilliant ride up until this week. I understand the tranny is sealed ? Any tips besides taking it to a dealer ? Problem is I live quite a ways from one, and finding the time.
View 14 Replies
I recently had some brake work done on my 2003 Jeep Grand Cherokee (139k miles), and they installed a new master cylinder. The following day, I was driving (very cold these days) and noticed the car had difficulty getting into higher gears and the engine revved up but would not accelerate. I had to stop, put in reverse, and start driving again. Then, the engine light popped on (P1763 - Governor Pressure Sensor) and has remained on for three days. The car runs fine most of the time, but occasionally experience the loss of acceleration. What should I do?
View 5 Replies
When I first got my car it had a flat spot while driving hard at higher rpms. Almost as if something were actually holding the car back, it would pull nice up to that spot and then just almost die off. I eventually got unitronic flash and it seemed better but it was still doing it. Later companies started coming out with dsg flashes and this seemed to be the remedy but I now have hpa dsg flash and it still does it from time to to time. Could this be a faulty coilpack, or an issue with the intake manifold valve that changes over at higher rpms?
View 4 Replies
So I have a 2005 Hyundai Elantra, it is a manual transmission. I was having problems with the rpm's going higher than normal at random times while driving, then I noticed that the fluid in the clutch fluid reservoir was low. I determined that to be caused by a bad clutch slave cylinder that was leaking fluid. So I replaced the slave cylinder and that seemed to fix the problem, but now I am noticing that the car lacks power when I'm going up any sort of hill or trying to accelerate faster than normal.
When going up a hill the rpm's will go up and I have a hard time maintaining my speed. When trying to accelerate fast, as in pulling out in front of someone or similar situations, the car seems sluggish and it seems like I need to shift because the rpm's are high but I'm not going fast enough yet for the next gear.
This sounds like it would be some sort of problem-related to the clutch going bad or could the leaking slave cylinder have damaged the clutch. Or does this sound like more of a different problem, maybe something with a fuel filter or something?
View 16 Replies
I have a 2012 elantra limited about 9 month's old with about 14,000 miles on it.
About a week ago I began noticing a burning smell. I first chalked it up to being 1,000 over the 3k mark for an oil change. However I then started to pay attention when I parked if there was any sign of fluids leaking. At first I didn't notice any or seemed like one or two drips. Well tonight I noticed a larger puddle that was def not water.
The other symptom is that it's been shifting up at higher RPMs. Tonight when I got on the freeway I was trying to speed up to 65 but the rpm gauge had me at over 4,000 rpms with normal acceleration...I was not gunning it. I also could not get the car to go past 60 at first, all the while the rpm increasing still, until I let off the gas then hit it again and seemed to trip it to shift and was able to get to 65.
View 23 Replies
I have a 2012 elantra manual transmission. I noticed the eco mode but never found out if it really does anything. when I shift from 1st to 2nd at higher RPMs its rough. At other gears its ok but I feel like the gas pedal is weak sometimes. With a manual does the eco mode make that more difficult?
View 12 Replies
I bought a new 2014 Elantra last Monday. Around 100 miles (Wednesday) I noticed it was making a ticking noise when accelerating. The sound gets louder at higher RPMs and goes away when I get off of the accelerator. You can't hear it over the radio but it's embarrassing when my passengers do. It almost sounds like a puff of air escaping or something, similar to a go-kart engine lol.
Anyways, I took it to the dealer Thursday and they drove it and said the noise was normal during the engines break-in period and if it persists after 15k to bring it back and they would see if there was something that needed tightening.
View 27 Replies
I inherited this car from my grandmother when she passed. It has low miles, around 40k. Since I paid zero for it, I would like to keep it. Historically I have done all my repairs, but never trans work.
Here are the symptoms. The car has issues shifting into higher gears. I have to punch the gas and then it will switch gears. It then began to do this for reverse, and now now reverse does not work at all.
At first I thought it was a speed sensor problem, but when I took it in to be read, it came up with P0734. It could be electrical (Speed sensor?), low fluid (it's not low), or 4th gear.
Is this transmission worth me fixing or paying to have it repaired, or should I move on?
P.S. If I drop the pan and find shavings, I understand that to point to 4th gear and bearing (also what the computer code read as the issue). Do shavings mean it definitely is 4th/bearing, or could it be another blown part?
View 4 Replies
My car is making a sort of whining noise; it sounds like some sort of tire noise, but I checked the tires and don't see anything that could be problematic. My husband checked to see if anything was rubbing, and doesn't find anything. The car is quiet when it is not moving, and the noise gets somewhat louder and slightly higher-pitched as I accelerate. It almost seems like the noise changed on a different road surface, but again, I don't see anything different with the tires. The car has about 140-150,000 on it. The noise has only been noticeable for a couple of weeks. No other problems, no change in steering or handling. No incident that I can think of that could have been a catalyst.
View 4 Replies
Why does my 2000 chevy impala whistle when i accelerate? it also seems to shift hard.
View 10 Replies
I started to realize something very weird in my car. While in drive from a stop I would accelerate and the car doesn't seem to shift up when its suppose too. I know that my car shifts around 2.1k RPM smoothly into second gear but now it would go all the way up to 3K RPM and slams into second gear which is really weird. Sometimes it does this problem and sometimes it doesn't. I would say 70% it would slam into gear. Not only does it slam but it would seem like this car does not want to shift at the proper rpm even when i foot is on the gas pedal very lightly.
Once I got home I tried some stop and goes and see if the problem persist. It still did. Then I tried doing shiftronic and from first gear once the line touches 2k RPM i shift up and yet it would still lag and the needle would go up to 3K RPM once again. This seems like a very bad problem especially MPG wise. I am still under warranty, I think because I've only swap the air filter with a drop in K&N and just plasti dipped my wheels and such.
View 28 Replies
Purchased my 2013 Elantra GT a few months ago and have been having a problem that had stumped everyone at the dealership. Thought I'd see who else is having it and what the thoughts are. To start, this is a 6SPD Manual Transmission.
Problem: Say you're at a stop and begin accelerating in 1st gear and then shift into neutral because you have to come to a stop again. When operating normally, the RPMs immediately wind down to idle. Well for me, about 15% of the time or more, the RPMs will take up to 10-15 seconds to wind down to idle. During this time, you cannot really shift into 1st gear because the RPM are too high.
The dealership has been working on this issue since last month. They replaced some parts and it is still doing it. They got diagnostic data and told me the throttle was sticking. No one could figure it out. Engineers got involved from regional, and it got pretty heavy as far as time. After several attempts at figuring out the problem and replacing things (which didn't resolve the issue), the engineers drove another new GT and found it was also doing it. So all of a sudden they said "it's normal" and closed the case.
Chances are, if other new ones are doing it, so is yours. I got second opinions from other auto shops who said it is not at all normal and that there may be a defect in the design. I've owned 4 Manual Transmission cars and I have never seen this before. If you're curious and have the 6spd manual version of this car, the easiest and quickest way to see this happen is accelerate in 1st gear to about 4000RPM and shift into neutral. Eventually, it'll get stuck and take a significantly longer time for the RPMs to return to idle. Usually when it finally happens, it'll keep doing it for several subsequent acceleration cycles.
View 36 Replies
My '00 V10 4x4 w/ 163k miles has had a rough shift from 2-3 (30-40 mph) with high rpms. If I let off the throttle before the shift I can get it to shift smooth, but if I don't let off the throttle it can shift really hard. I only have this issue from 2-3 and it has not gotten worse since I bought the rig almost two years ago. Driving conditions are around town on occasion and for towing a 3k pound pop up. Maybe 2k miles a year so far? The hard shift happens whether towing or not.
I have done just a drain and fill on the trans fluid a year ago. Have not had time to change the filter (even though I have read it's not necessary). I am planning on doing another drain and fill soon along with the filter since I have one and cleaning out the trans pan.
When searching on FTE I read a post about the accumulator springs that can go bad and was wondering if maybe this is the problem? Since I am planning on doing the filter change I was going to do the spring replacement while the pan was open.
View 9 Replies
