I just replaced the clutch plate and throw out bearing since the clutch was bad but now its like the clutch has seized up or maybe the transmission is bad. I did start it up and a friend of mine Idk stepped on the gas or something and blew the clutch master cylinder.
2001 Hyundai Elantra ... I dont know anything about this car ....
I just bought a 96 f250 5.8
Upon driving home, i tried the ac again and the ac clutch started to smoke. I replaced the clutch with one from autozone, but when I tried it again, it made a screaming death noise upon clutch engagement. Is my compressor seized?
I tried to turn the clutch (not the pulley, that spins fine) by tapping one of the slots and bolts with a screwdriver/hammer. It was firmly locked in place. If the compressor was OK, would it have turned easily? If I need to replace the ac pump, who sells a good/cheap/reliable one?
My wife has a 02 Ford Escape XLS with a I4/manual trans, she has been saying it has been making weird grinding noises for a while but has not been able to replicate it for me to hear. Today it locked in gear and stalled, she can depress the clutch and start it, but can't take off in whatever "gear it thinks it's in" and it'll stall. To quote her.
So odds are the clutch or trans is toast, I'm more of a full size truck guy when it comes to doing work, what to look at? She's getting it towed and I have enough tools to do the job just not a ton of time this second to do the research, When I know more I'll add it.
2007 Accent pedal won't depress. Bearing making noise for a few months. Is tranny snout toast or is it fixable?
View 2 RepliesWe swapped transmissions in 01 elantras.. We installed a new clutch kit . When we go to start the clutch won't completely disengage, it only pulls it some, not enough. We replaced Tran fluid and bled it. We swapped out the throw out bearing arm and at first it worked now it doesn't..
View 3 Replies2002 Elantra
Replaced new clutch disc and new pressure plate.
Without turning on the engine, the clutch pedal seems to get harder to press, until it can't be pressed down anymore. The pedal can't be pressed down.
Clutch fork lever does not release.
I drive a 2001 Elantra, 5 speed manual, about 135k km on it which is about 85k miles. Yesterday I felt the clutch pedal was engaging unusually low or was not as resistant to the weight of my leg as is usual. I could drive it without much trouble though.
This morning the pedal went all the way to the floor with virtually no pressure exerted on my half, and shifting gears was pretty much impossible without excessive force, so I parked it and walked to work instead. It felt like I was shifting gears without stepping down on the pedal, even though the pedal was all the way to the floor.
I then checked the fluid in the reservoir and it was at the max, but it was black like oil. I've done some reading and I'm thinking replacing or cleaning the master and slave cylinders could work. Am I way off?
We are in need of a 4th clutch for our 2004 Elantra. This is a despicable record for Hyundai.
View 14 RepliesHere's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?
I am currently driving a 2005 Elantra (manual trans) with only 48k miles on it. Less than a year after buying the car new the clutch had to be replaced (around 10k miles) and now the second clutch is about to go as well. I do not ride the clutch or drive like a maniac so there is no reason to be on a second clutch at 48k, let alone a third one. Is there anything I can do besides putting a new clutch in to protect against this problem in the future? Also, would installing a stronger, high-performance clutch work?
View 1 Repliesi replaced my a/c compressor on my 2006 f-250 2 yrs ago but had not refilled with r134..only the pag oil. Now i decide to refill seeing my wife uses the truck and compressor would not engage, i was able to bypass it by removing relay and jumping it with a paperclip. Compressor started up but seems to have seized on pully. the pulley seems fine and still turning freely. I can no longer turn it manually when truck is stopped and i could before i jumped it. could the clutch only be replaced or does the bearing and pulley have to be replaced
View 10 RepliesMy 02 elantra gls 5 speed clutch has gotten stuck engaged for about the third time now. First time was right after I bought the car i noticed the clutch would slip randomly for no reason. At first i thought the clutch must need replaced, but then other times I couldn't make it slip if i tried by going up steep hills with car full of people and shifting too soon on purpose and punching gas....no slip. So anyways i replaced the slave cylinder, and all was good till one day my wife calls me up stranded and says clutch pedal is rock hard and none of the gears will engage. so i tow the car home and fiddle around and realized the slave cylinder (brand new one) was stuck out. I opened the bleeder and it returned without me having to push on it or anything. i then bled the system thoroughly. So months have gone by and the slave cylinder got stuck out again, and again it was a simple turn of the bleeder valve and it went back and works fine. just curious as to how i can fix this problem permanently since its irritating and seems to be reoccurring. do i need to replace the master cylinder as well or did i buy a bad slave cylinder?
View 6 RepliesIn every other manual transmission vehicle I have ever driven, the clutch pedal engages/disengages within an inch of the floor. Is it normal that the clutch in my 2002 Hyundai Elantra engages when the pedal is so far away from the floor? When I say far away from the floor I mean within an inch of the pedal being fully released.
View 21 RepliesI am searching for any kind of adjustment that might enable me to force the clutch level to the positive stop. It stands off about an 1/8" to 3/16" and I think is the reason I am not getting engagement in first gear, it slips heavily but fine in all other gears. The key way on the the lever prevents me from moving it a notch or two if I thought I could and don't know if that's even the answer . I can't figure out what is preventing it from returning fully on its own I can push it by and and a little fluid will squirt from the reservoir. Ive replaced the slave cylinder and bled it.
Is there any adjustment under the dash? This is a 2001 elantra that I just put a 2000 trans 5 speed.
My original plan was to pull the parts from the 2000 and replace in the 2001. I had lost 1st and 5th totally and found a 2000 that went right in with some minor mtr mnt mods. It shifts just fine except for this 1st gear thing. I saw a video and am having second thought about that move. I dont really want to pull the trans out again.
1st gear just keep slipping. new clutch kit installed when I swapped them out. It feels like a linkage thing somewhat but I cant find adjust ment to tryout.
Alright so I've had this car for about six months now and the clutch was supposedly replaced by the dealer I got it at. The clutch usually grabs about half way up but sometimes it's higher. I replaced the master cylinder because it blew out, when changing my I take I noticed the slave was starting to leak so I replaced that about three weeks ago. Ever since then, the clutch seems to grab differently and seems to be taking longer to engage.
Now, I did the "slave mod" on the old one AND the new one so it's not that. Do you guys think the new slave is bad? I have high temp dot 3 in there (I try to only use the best fluids for my cars). It just doesn't seem to grab as hard as she used to. Like it takes a bit longer to engage. The clutch (should) only have 15k miles on it. The clutch parts are under warranty but I'd still have to pay for labor since it's a wear part. I'd like to avoid replacing it if it's that new u less it's definitely going.
I have a 2002 Hyundai elantra gls with 190,000 miles on it. I have a scraping noise coming from the transmission when the clutch is not pressed in, the noise is present whether I am in gear or just in neutral. If I press the clutch in than the noise will completely go away. I have searched and found that these symptoms usually mean its an internal transmission problem and not just the throw out or pilot bearing.
View 4 RepliesIn less than 30,000 miles, I've replace the clutch, throw out bearing, and pressure plate three times. Dealer adjuster clutch at 12,500. First replacement at 15,000 miles. I do not ride the clutch
View 8 Replies2013 Elantra manual. 60,xxxkm, owned from new, purchased in August 2013. Oil changes always done within 5-7000km. Was 2000km over my oil change due date when this happened (haven't had time to get it done, been driving my motorcycle mostly). Driving around today I dropped my wife off, then I heard a quiet ticking noise under very light acceleration.
The noise would go away under normal acceleration, no noise while revving, and no noise while engine braking. The noise got worse after about 5km. I was in traffic and engaged the clutch into first gear, the car stalled violently. Turning the key results in a click, then nothing. In 1st gear the car will not roll forward. In reverse the car will not roll back. It still rolls in neutral. Had it towed to my local Hyundai dealer and got a rental. Waiting on the results.
Never saw a drop of oil on the ground while parked, and never smelt any oil burning. I run between 87 and 91 octane, whichever is available. I have the extended 160,000km 8yr warranty, hopefully this is covered as I still owe about 15g's on the car.
I was driving the car down the freeway, hear a loud bang from underneath the engine, immeadiately ceased accelerating over 15 MPH and would not reverse.
As it stands now the car will start up, but not reverse, or accelerate over 15 MPH without the RPMs revving like mad. Think it might be tranny-related...
I have a 2003 Santa Fe 2.4. Couple days ago my idler tensioner pulley or whatever its called seized up and took the belt out with it. I got a pulley that resembles it from Autozone mind you that it was the only parts store that had one in stock even Hyundai didnt have the part. The only difference is the hole size for the bolt is about 1/4 inch bigger then the stock pulley. Is there any chance I can get a spacer and make up for the difference?
View 6 Replies2002 2.7L. Engine seized. Bought a replacement also from a 2002. Tried to start today and no spark. I just replaced the physically broken crank position sensor. That seemed like it would be an obvious and easy fix, but still no spark. The broken sensor had frayed/shorted wires. Could that have damaged the PCM /ECU? There is a 2003 Santa Fe at U-Pull-It that was running when it came in. Will the PCM from that work? I am running out of time. I have to have this running before I leave on a flight tomorrow night. I do have a code reader (if I can find it) but I can't imaging it would have any codes if it hasn't started since I had the battery out. Not sure how that works.
View 4 Replies