2002 Elantra
Replaced new clutch disc and new pressure plate.
Without turning on the engine, the clutch pedal seems to get harder to press, until it can't be pressed down anymore. The pedal can't be pressed down.
Clutch fork lever does not release.
2001 Elantra, Hand brake stuck, is there a release button? I can not seem to release my hand brake. How can I release it so I can make adjustments?
View 2 RepliesMy 02 elantra gls 5 speed clutch has gotten stuck engaged for about the third time now. First time was right after I bought the car i noticed the clutch would slip randomly for no reason. At first i thought the clutch must need replaced, but then other times I couldn't make it slip if i tried by going up steep hills with car full of people and shifting too soon on purpose and punching gas....no slip. So anyways i replaced the slave cylinder, and all was good till one day my wife calls me up stranded and says clutch pedal is rock hard and none of the gears will engage. so i tow the car home and fiddle around and realized the slave cylinder (brand new one) was stuck out. I opened the bleeder and it returned without me having to push on it or anything. i then bled the system thoroughly. So months have gone by and the slave cylinder got stuck out again, and again it was a simple turn of the bleeder valve and it went back and works fine. just curious as to how i can fix this problem permanently since its irritating and seems to be reoccurring. do i need to replace the master cylinder as well or did i buy a bad slave cylinder?
View 6 RepliesWell, like the title says, The trans is stuck in third gear, with no other gears, or neutral or reverse. The car is slightly modified 02 GTI 337. APR Chip, Forge TIP, Full 3" exhaust, Greddy FMIC. I definitely drive the car, and had been beating up on it on the highway for a little on my way in to work, then on the way home, down shifted to pass someone, dropped it third, passed them, went to shift to fourth, Shifter moved, felt like it engaged "a gear" and then then i let off the clutch and it was still in third.
I also noticed that unless, I press the clutch in the, the car stays in this gear, even when the shifter is in neutral. I looked at the linkage, and it appears to be functioning. I did some reading around the Vortex and it seems like this might be a shift fork problem. Also, if the trans will be apart, what items should be upgraded?
So I took my tranny off to fix a broken dog bone mount bolt problem. I am now in the process of putting it back on. I raised the tranny bolted all the bolts on had everything almost back together and I went to put my slave cylinder in and the clutch fork won't move so that the slave cylinder can slide in. Did I maybe put the clutch fork in wrong? pretty positive I put it back in as it was and slide the clip through the hole and everything.
View 11 RepliesI have a 2001 ford f150 4x4 xlt and it seems to be shaking violently in first gear when I try to release the clutch slowly. The person i bought it from said he had a new clutch put in this year So i don't think its the clutch. What could be the cause of it before I take it in to be checked.
View 2 RepliesI need to tear down a zf6 out of a 2000 powerstroke to replace a broken clutch fork and a a worn input shafts. What special tools do I need for this?
View 2 RepliesMy 01 GTi (12v VR6) was having some trouble shifting into, and out of, first and reverse so after a bit of research I decided to try adjusting the shift linkage as it seemed like a possible easy fix. After doing that I tried backing it up in the driveway and after a couple of shifts to different gears it ended up getting stuck in reverse. When I pushed in the clutch pedal to let it roll forward I noted that it seemed to be resisting rolling forward despite the steep incline. Once it reached a less steep incline it stopped rolling forward completely, so I'm thinking that it probably won't come out of gear because the clutch won't disengage all the way.
I've done some searching around and from what I've read so far it sounds like it could be a worn or damaged clutch fork, the hydraulic lines, master or slave cylinder, or even a broken clutch plate. What I don't want to do is pull the transmission and clutch, only to find that it was something much easier to fix.
I just replaced the clutch plate and throw out bearing since the clutch was bad but now its like the clutch has seized up or maybe the transmission is bad. I did start it up and a friend of mine Idk stepped on the gas or something and blew the clutch master cylinder.
2001 Hyundai Elantra ... I dont know anything about this car ....
My girlfriend's 2001 cavalier has about 160k on it and about a week ago it started shifting harshly accelerating to highway speeds and the CEL came on along with the traction control/abs warning light. I pulled the OBD2 code and it was P0742, Torque Converter Clutch Circuit Stuck On. We took it to the transmission shop down the street the next day and they wanted $600 to diagnose. We called 'shenanigans' and decided she should take it to her regular shop. On the drive over the transmission shifted normally. Both shops noticed that the transmission cooler lines were rusty and seeping, but neither thought it was the cause of the problem. The shifting issue hasn't recurred even after a couple hundred miles during the week. She hasn't had the transmission fluid changed and doesn't know if it had been when she bought it about 80k miles ago. It seems to me that pre-emptively draining the fluid, changing the filter and refilling, especially to check for debris in the fluid, would make sense, especially if it was debris jamming the circuit that caused the error code in the first place.
View 8 RepliesI have a Hyundai elantra 2002 that is stuck in second gear. I was driving it, I came to a stop sign so I put it in neutral and when I shifted into first i heard a pop. I started driving and when I shifted into second I noticed the shifter was really loose, when I tried shifting into third I couldn't.. it is like there is a brick wall. I can shift from 1st to 2nd but the shifter just moves up and down. Also if I let the clutch up it stalls the car. I was told that my car is stuck in second gear.
View 1 RepliesWe swapped transmissions in 01 elantras.. We installed a new clutch kit . When we go to start the clutch won't completely disengage, it only pulls it some, not enough. We replaced Tran fluid and bled it. We swapped out the throw out bearing arm and at first it worked now it doesn't..
View 3 RepliesI recently started getting transmission problems with my 2001 elantra.. the car would slam into second gear and the check engine light would come on and it get stuck in 3rd gear.. The codes I am getting are P0720, P0715, P1529. I searched and i found that most people that had this problem replaced the input and the output speed sensor and the problem is fixed.. so i went and i got two new sensors and replaced them i am still have the same exact problem... the car drives good for the first 5mins and then it would slam hard into gear, check engine light comes on the it get stuck in third gear...
View 6 Replies2001 Hyundai Elantra 183 miles.
codes- p0720 output speed sensor circuit malfunction, p0500 veh speed sensor a malfunction.
Recent fixes on my 2001 Hyundai Elantra.
A few months ago i had my speed sensor cleaned, and a power steering leak. No problem after that was fixed and cleaned the sensor. Soon after that my water pump went bad and i had that replaced along with 3 new belts. Just last week i had my front driver side replaced with a new wheel bearing and axle.
My Problem then and now.
My problem months ago, my car would be shifting into different gears as it pleased; while driving or sitting at a light i would feel it jump and it felt as if it was stuck into 2nd or 3rd gear as i was driving. My engine light would soon come on after this. To accelerate i feel as if i had to floor my pedal when the shifting or engine light came on. I looked up my codes and they are the same as they are now. I read about same problem and fixed it by just cleaning the speed sensor off. My friend and i did the same thing and it fixed those issues. My problem now is that i just had my axle and wheel bearing fixed (my car moves smoother and quiet) my engine light came on again, it had not been on since, i read the codes and they are my speed sensor same as before but my car has not been shifting as it was in the past. Would this be because the sensor needs to be cleaned again or replaced, or because of my new replacements on my wheel.
I drive a 2001 Elantra, 5 speed manual, about 135k km on it which is about 85k miles. Yesterday I felt the clutch pedal was engaging unusually low or was not as resistant to the weight of my leg as is usual. I could drive it without much trouble though.
This morning the pedal went all the way to the floor with virtually no pressure exerted on my half, and shifting gears was pretty much impossible without excessive force, so I parked it and walked to work instead. It felt like I was shifting gears without stepping down on the pedal, even though the pedal was all the way to the floor.
I then checked the fluid in the reservoir and it was at the max, but it was black like oil. I've done some reading and I'm thinking replacing or cleaning the master and slave cylinders could work. Am I way off?
We are in need of a 4th clutch for our 2004 Elantra. This is a despicable record for Hyundai.
View 14 RepliesHere's the scoop: 2 year old clutch & flywheel with 21,000 miles on them. Clutch master cyl. is full & not leaking. The clutch slave cyl. moves when the clutch is pressed & is also not leaking. The shifter linkage has been checked at the shifter and moves freely as it should.
I started the car, put it in gear, let the clutch out and there is no movement from the car regardless of the engine revs. The engine runs freely and does not die with the clutch engaged and the transaxle in gear. Putting it in ANY gear (including reverse) has no effect. The car will not move.
After turning the engine off I left the car in gear, left the e-brake disengaged, released the foot brake and the car stayed put. I then put the shifter into neutral, let the foot brake off and the car began to roll. I stopped, put the shifter back into 1st, let the foot brake off and the car was again stationary and did not roll. This tells me that the shifter linkage indeed works and that the car WILL go into gear. So, why won't the car move under power?
I am currently driving a 2005 Elantra (manual trans) with only 48k miles on it. Less than a year after buying the car new the clutch had to be replaced (around 10k miles) and now the second clutch is about to go as well. I do not ride the clutch or drive like a maniac so there is no reason to be on a second clutch at 48k, let alone a third one. Is there anything I can do besides putting a new clutch in to protect against this problem in the future? Also, would installing a stronger, high-performance clutch work?
View 1 RepliesA problem that has raised on my Elantra GT is in the hatchback, the trunk handle gets stuck in or out so when I try to open the trunk it wont, but if I push the handle in first and then open it then it opens, also I have to lock and open the car with the alarm remote several times before it opens. Now I know that the handle is bad and need to change it, the car is a 2002 and this happened on 2004 I told the dealer and refused to do anything about it unless paid for everything, They wanted like 300 to change a handle, i did not do it, I will buy a handle and do it my self, I just wanted to know if other people had run to this problem and if its hard to change the handle, the dealer said they needed to take the whole hatch apart, but as far as I can see its only 2 screws and the handle should come out. This is been a long time coming.
View 5 RepliesIn every other manual transmission vehicle I have ever driven, the clutch pedal engages/disengages within an inch of the floor. Is it normal that the clutch in my 2002 Hyundai Elantra engages when the pedal is so far away from the floor? When I say far away from the floor I mean within an inch of the pedal being fully released.
View 21 RepliesI have a problem with my 2005 elantra making a noise that sounded like it was coming from the cam timing chain. since it is still under the 10 year 100,000 mile warr. I brought it to my dealer. I had a P0011 code for advance timing also that keeps popping its ugly head. Dealer said that the chain would not be covered under warranty because of oil sludge and a faulty oil control valve. I went to remove the ocv from the head and when I removed the bolt the solenoid came off without the stem I tried an easy-out and managed to rotate it approx 1/8" but no luck getting it free to pull out.
View 1 Replies