AutoZone provided this code for my check engine light: P0010.
Definition: Intake camshaft position actuator circuit open
Explanation: ECM has detected a low voltage on the VCT circuit
Probable Cause: 1) Open or short circuit condition on the VCT circuit; 2) failed VCT solenoid
Is there a part I can replace myself that can fix this, or is this a dealer repair?
We have a 2002 elantra...went to auto zone and they ran the test and came back with code u0d00...but they didn't have an answer for it in there computer..
View 4 Replies2003 hyundai accentra and I have trouble code P0303 misfire detected cylinder 3 the car would run rough and hesitate at idle and run rough in drive and reverse I checked the plug gap on number 3 cylinder and it was excessive so I regapped it and put back and the car run good for about a day and now the engine light is back and is running rough and hesitating.
View 1 RepliesI recently bought elantra 2004 gls, with 107k mileage.
Few days ago the check engine light came on while I was driving it. The next day it went off. This happened today also. I didn't notice anything wrong with the car, no smell, tranny fluid is recent, oil change 2.5k ago.
The code was p0501, speed sensor.
I keep getting the same code for the check engine light of P0128. I have replaced the thermostat twice and the ECT sensor already. I do know know what else I can do for getting this fixed. I have checked the fans and they are working correctly. I have also checked to make sure there is nothing wrong with the head gasket. My car does not over heat, but it does take forever for the temperature gauge to rise. This is for a 2006 Hyundai Elantra. What else I can do?
View 2 RepliesMy car is a Prius Plus 2012.
One day, I decided to go to a mechanic to clean the EGR pipe. Only the pipe, not the whole EGR. It was an extremely simple operation a mechanical one, not electrical etc. Starting from that day, when I go with the car, from time to time, check engine lights up. For a fraction of a second to up to 2 seconds then it disappear.
The car behave itself without a problem. But still the on-off check engine is really annoying.
So a went to the dealer. Put the car on tester.
Result: no code error !
I went to another garage , put another tester on the car, no error..
How can I actually see what the error is if nothing is stocked in the ECU of the car?
I own an 04 Hyundai Elantra with around 196,000 miles on it, and have run across a problem I haven't had to deal with before. A few days ago, my check engine light came on while driving. I didn't really notice much, but when I started it again it began idling roughly. I got it home and pulled the code, which was P0341 (camshaft position sensor). This isn't the first sensor I've had go on the car (I replaced an oxygen sensor and throttle position sensor a couple years ago), however I ran into two problems:
1. How likely is it that it's the sensor that's bad as opposed to something like the timing belt or VVT adjustment?
2. Since the sensor isn't horribly expensive, I decided to try replacing it, but I can't get any socket to fit on the bolt that secures it. I've heard it's a 10mm, but nothing seems to fit snugly. Maybe there's just so much crud and corrosion that it's ruined the head. I tried using an extraction socket, but no luck.
I just got this very nice Elantra 04 with 64k on it. Yesterday suddenly I got the check engine light on. Today I went to Auto zone and they have checked my car and it showed code P2626. But there are more than a few suggestions about what could be. I don't know what to do. See the attachment below.
View 1 RepliesI recently had the engine light come up on my Hyundai Elantra 2003. I read the code with my cheap little code reader with the torque lite (free) app on android. It threw the P0128 code which means a faulty thermostat.
Here's the web link to all the details on the code: [URL] ....
I have checked the coolant level and its good. The strength of the coolant is good to -40 Celsius. The engine fan is not running at all. I recently changed the thermostat. I'm leaning towards faulty ECT. The car takes forever to blow hot air too. It has done weird readings in the past with the temperature gauge in the cab.
I just bought a infrared temperature reader of Amazon and want to check the temperature where the water comes out of the engine past the thermostat and compare it to the reading on the torque app readings. I'm thinking it won't match.
I bought an 04 elantra a few weeks ago. The check engine light is now on and I get code P0420 listed twice with my code reader. I have replaced the downstream O2 sensor and reset the codes only for them to return again. It is my understanding that this is going to be a convertor problem. My question is that from the research I have done it looks as though this car has two converters. One at the exhaust manifold and then another in the tailpipe. Which one is going to be the most likely causing my Check engine light to come on. Or do I need to replace both converters.
View 5 RepliesI have a 2003 Elantra GLS. I am intermittently Check Engine light and error code is P0113 - Air Intake sensor issue. I can't locate where the sensor is. I don't see any wire coming of the tubing that connects the air filter to the engine.
View 18 Replies2004 Elantra AT ... 6 months ago top of the radiator cracked caused it to overheat and blow the head gasket and warp the head. Repaired that and compression is fine now. It ran great for 4 months but now it randomly stalls. at or near idle. Seems to do it more at operating temp rather then cold. Occasionally the check engine light will pop on and the code reads (random misfire). It acts just like it has been shut off. But immediately restarts.
View 3 RepliesI had a check engine light cane on. I took it for it to get checked and they gave me this code- P0457 EVAP small leak detected. ECM has detected a large leak in the EVAP System during a system monitor test.
The paper said I had a leak in the Evap canister or hose. I took the truck to a mechanic and was told I had Bad oxygen sensors. Can Bad/Dirty oxygen sensors make this error code come up?
Exactly where the oxygen sensors are? I was told they were behind the mufflers but I didn't see any and the diagram I found was not accurate.
2002 Ford Ranger XLT v6 extra cab.
I have a 2002 Jetta 1.8t. My check engine light came on and it gave me the code P0135 sensor heater circuit. Bank 1 Sensor 1. We bought a new 02 sensor and replaced it. We definitely bought the right one too. Cleared the codes. After a little driving the CEL came back on with the same code P0135. What is wrong and how I can fix this?
View 6 RepliesI cleaned my k&n air filter on my 02 passat 1.8 turbo let it dry oiled it very lightly, and 50 miles later I get a check engine light on, pulled the code 16486 and it says Mass or Volume Air Flow Circ Low Input. Cleared the code put a frame in until I can get it filter. Why that would throw me that code, k&n oil gumming up my sensor??
View 2 Replies1996 izusu rodeo had check engine light on got code for egr valve. Replaced it light when out drove fine all day. Stopped at grocery store came back out would not start ... Will crank over but will not start. did a obg (two) scan get a p1640 output A circuit fault code along with a 1460 egr code ....
View 5 RepliesI have a 2007 f250 and got a check engine code icp circuit intermittent and to what I know icp sensor should be on the valve cover on the passenger side but it's not I bought the truck few months ago could it be that they swapped the engine for an early 6.0 or is there any other place for the icp sensor???
View 7 RepliesI went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 RepliesEngine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?
I have a 2003 Santa Fe, V4, 2.4L.
So the other day, my CEL and I got it scanned: p0320, or "Ignition/Distributor Engine Speed Input Circuit Malfunction."
It was accompanied with two symptoms:
1. The car will sometimes sputter on startup, and the tachometer will be zeroed out. I have to turn the car off and turn it back on, and it will start normally, albeit with a bit of a misfire on idle.
2. The car will sometimes die while at a stop. Just like the first symptom, if I turn the car off and turn it back on, it will work normally.
I looked on here, and it seemed like everyone solved a p0320 by replacing the Ignition Failure Sensor. So that's exactly what I did. But nothing changed; I still have the symptoms, and the CEL came back on and is still reading p0320.
What should be my next step? Could it be faulty wires that give power to the Ignition Failure Sensor?
just bought an mk4 1.8 jetta and so I love it, however I'm having a couple issues. I've got a cel for code p0010 something about the camshaft position sensor. I changed the sensor with a new one and the problem is still there. I've got pretty much full power but no turbo spool and my boost gauge tops out at 5-6 psi.
View 5 Replies