Elantra XD (2001-06) :: Camshaft Sensor Error Code After Tune Up
Jun 20, 2014
I just had a ton of maintenance done on my 2003 Elantra. Spark plugs & wires, timing belt, drive belts, water pump, replaced coolant and replaced the transmission fluid. The spark plugs are NGK platinum as recommended in my handbook. As soon as the mechanic started the car after the tuneup, the engine light came on with a cam shaft sensor code. He said it went off on its own.
The engine light came back on when I started the car. There's also a major loss of power after coming to a stop. I have to floor it to get it to go anywhere above 20 mph after a stop.
The mechanic said that when he replaced my water pump the liquid splashed all over everything and he thinks he might have gotten something wet that shouldn't have gotten wet and that all will be fine after it dries.
View 2 Replies
Advertisement
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
View 4 Replies
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
View 4 Replies
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 Replies
My check engine light came on the other day, and I went to Autozone to have the code read. Of course, that indicated the camshaft position sensor was detecting a fault. I read through all the posts relating to the fault, headed up to my local Hyundai dealer, and picked up the oil flow control valve for about $50 plus tax. While I was there, I figured I might as well have them do an oil change, since it was way past due. No point in putting in a new part with dirty oil..right? They did the oil change, washed the car and I was ready to roll. My plan was to replace the part myself, but magically, the check engine light has not come back on since.
View 8 Replies
I have a 01 Elantra and my daughter has a 02. Both cars have the camshaft sensor at the front (timing belt) end of the engine. My daughters car is a early model with a 01 engine in it. My understanding is that later 02 engines moved the camshaft sensor to the ignition coil end of the cylinder head. My question is did the timing remain the same so that if I put a 01 engine in a late 02 body and spliced the sensor in would it work correctly?
View 8 Replies
02 Santa Fe 2.4L/ automatic/2 WD. I replaced the fuel filter (only) and have had a nightmare ever since. It takes multiple tries to start, running a little longer each time. When it will finally stay running, only the most delicate of throttle feathering will allow any RPM's to be built up. Any attempt to do otherwise will result is sputtering, bucking and other unhealthy behaviors until the throttle is closed. It also gives off the smell of running rich.
I borrowed a scan tool and got P0136 and P0141, which I expect since the O2 sensor wiring was cut in two by the heat shield shortly after my daughter bout the vehicle. It also is giving me the P0340 Camshaft Position Sensor Circuit code. I had replaced the CMPS and its connector a couple of month ago. I replaced the sensor again to no avail. I have checked the Orange/Black wire from the connector to the ECM and it reads 0 ohms. I get battery voltage at the connector on the Blue supply wire but only get 1.86 to 2.0V when I check the signal with the engine running.
View 6 Replies
06 sonata 3.3 L V6. Light has been on for a month or two...took it in to mechanic yesterday and it's a camshaft position sensor error...it makes total sense to me now because my cars been starting hard, seems like it gets hotter then usual...and had a "clicking" noise for about 10 mins, then gradually goes away. it takes a few extra cranks now to start the engine unless it was already fired up.
Also does a jerk once and a while around 40 km/h. I looked online and those seem to all be symptoms of a failed camshaft position sensor (CMP). Would those symptoms seem about right? Am I okay to drive slowly for the weekend before I get the new sensor installed? The mechanic didn't seem to worries about me driving for just the weekend...but it's worrying me a bit...
View 2 Replies
For 2009 and 2010 f150's with the 5.4L engine, this may apply to you.
About a month back I got some odd vibrations at start-up and while driving and the following codes:
P0345 - Camshaft Position Sensor, Bank 2 (drivers side), circulation error
P0349 - Camshaft position Sensor, Bank 2 (drivers side), circulation Interim.
These codes are common in the previous generation truck for various reasons. In my case, I started trying to troubleshoot with the easiest solutions first.
Checked the battery - fully charged.
Checked/played with the alternator connection and related wiring - looked good.
Checked the oil - it was down at the half mark on the dipstick, so toped it off with synthetic oil.
Cleared the codes, and now have been driving for a month, no issues, no codes!
If these codes come up for other folks, try the easiest on the list first, before bringing to the dealer... these codes can be really hard to solve, but sometimes we can get lucky.
View 8 Replies
I'm getting error P0125 on my 2001 Echo, which points to possibly a faulty ECT sensor.
Where is this sensor located? Seems like under the air box? Is replacing this part as annoying as it looks? And, are there any other possible causes for code P0125?
In case it's related, I will mention that code P0171 (mixture too lean, I believe) is present as well, and the car does hesitate upon initial acceleration when standing still. Once it's moving, it works fine.
Maybe it's time to start thinking about replacing this car... it has 216,000 miles...
View 1 Replies
33k Civic 2001 "PO335 Crankshaft Position Sensor A circuit" error code
My Civic 2001 LX (non vtec 1.7) threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining.
View 4 Replies
My Civic 2001 LX (non vtec 1.7) 33k threw an error code today. It was, "PO335 Crankshaft Position Sensor A circuit" error code. It was raining a lot today, and this is the first day that it did it. I have never had this problem before. When the error code came on the engine automatically lost power. I couldn't get the car over 3000 rpm. Then it stalled in an intersection. Now it won't start period. It only has 33k on the clock.
The timing belt was done about two months previous, but i haven't had one problem until today, when it was raining. So much for a reliable honda.
View 4 Replies
While driving home my cel came on, the next morning I took it to the dealership. The code read camshaft sensor. The mechanic ask how the van was driving, I said perfect, no issues no nothing. He said that was kind of surprising.
The next morning went out and no cel at all and van still running fine. Spoke with another mechanic who said a number of things can cause that code and to hold off on the new sensor and see what happens over the next few weeks engine performance wise and if CEL comes back on.
What should I do? Car is a 2002 KIA Sedona mini van that has had zero engine issues while I have owned it since 2010.
View 9 Replies
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 Replies
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 Replies
A week ago I was traveling in my wife's 2009 RX350 at freeways speeds and outside ambient temperatures around 80 degrees. After traveling about 2 hours and stopping for about half-hour for lunch, I started the vehicle and went around a mile and the Check Engine light came on, the VSC was flashing and the traction control indicator was illuminated. I stopped quickly in a gas station and checked the manual for what the warning lights meant. Nothing of any value was found; I filled the car up and headed for home, about 4 more hours at highway speeds. The warning lights stayed on and the VSC flashed the entire way home. The vehicle ran perfectly with no problems at all.
The next morning I started the car and the lights were out. Still worried, I purchased an OBD2 scanner and pulled a P0015 code, Camshaft Position - Timing Over-Retarded (Bank 1). I erased the code and the car has been fine ever since. Finally to the question, is this something I need to worry about? I travel this trip about once a month and don't want to get stranded along the road. The car has 54K on it and if it is a sensor in the engine, it should be covered by the powertrain warranty, but more importantly, will it cause damage to the engine? I read that the camshaft position sensor would only be replaced under warranty if it was inspected and causing a loud ticking noise, which I do not hear. If it throws the same error code again, I will take it in to the dealer and let them look into it.
View 5 Replies
I am getting a p0501 code (off my code reader) on my 2001 Elantra. I have already replaced the Speed sensor on top of the transaxle under the air filter. Driving into work today check engine light came back on and took to AutoZone. They are getting a P0501 code Sensor "A". They had no idea which sensor, sensor "A" was. I know there are 4 sensors on this car and have searched for other posts with no luck, all say replace speed sensor. Need to get this done to pass emissions.
View 2 Replies
I am currently about 1700 miles into what is a, planned, 11,000 mile road trip up to Alaska and back to SC. The first three days of driving everything was fine and I was getting 33 MPG. Today my MPG dropped down to 28 and in the evening my check engine light came on. The folks at PepBoys told me it was P0139 which I understand has to do with oxygen sensors and would affect my vehicle gas consumption.
If I drive about 21 hrs (Denver to Portland OR) to get to a place where I have a trusted mechanic and more free time, will it be bad for the car/engine?
Driving: Elantra GLS, 2003. Around 53k miles on it. Just replaced the tires last week as well as all belts (including timing). A few years ago I recall a similar error and my mechanic had me take the car to a muffler shop to cut something out and reweld it. yeah, I have forgotten the details.
View 10 Replies
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 Replies
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 Replies
The computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 Replies
