Elantra XD (2001-06) :: 2003 - CEL Code P0113 / IAT Sensor High Input
Aug 8, 2013
So my mom recently bought a 2003 Elantra (75K miles, auto trans) and within a few days the CEL came on. She took it in to PepBoys and had them hook it to their scanner to get the codes out of it. The only code that came up was P0113 Intake Air Temp (IAT) Sensor high input. I've done a little research on the net but there is a lot of random info for this code out there. Is the IAT a separate sensor or is it combined in with the Mass Air Flow (MAF) sensor(if this car even has a MAF) or combined in with the MAP sensor? I've read on the net that it could be any of these 3, I think it's combined into the MAP.
I've also read that this code could be caused by a bad IAT, bad O2 sensor, an exhaust leak, bad wiring/ground(I checked the wiring/grounds visually and everything seems ok) or many other things. If it's as simple as replacing one of the sensors I can do that myself, I just don't want to go randomly buying things and either it be the wrong part or have it be the right part but not fix the problem. The car runs great, even with the CEL on. Yesterday when she stopped by my house I disconnected the battery for a couple minutes and reconnected it, started the car & no CEL. She drove the car for about 125-150 miles before the light came back on.
View 10 Replies
Advertisement
Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.
View 15 Replies
I have a 2003 Elantra GLS. I am intermittently Check Engine light and error code is P0113 - Air Intake sensor issue. I can't locate where the sensor is. I don't see any wire coming of the tubing that connects the air filter to the engine.
View 18 Replies
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ....
View 3 Replies
2003 Hyundai Elantra, 1975cc engine, XD. P0198 Error Code.
I know this is the Engine Oil Temperature Sensor High code and I have seen indications this may mean high voltage on this sensor. My problem is I cannot locate this sensor on the engine. From what I have read this sensor is supposed to be on the driver's side of the engine on the head, rear side.
On my engine the head was replaced (unknown to me when I recently purchased the vehicle). From all indications this is not a CVVT engine. The air intake has a MAP sensor that is connected and appears to be functioning properly. The driver's side of the engine does have two coils but I can see no other wires from the wiring harness toward the rear of the head other than leads to the starter.
The cam sensor is located on the passenger side of the engine, rear side. I have found the oil pressure sensor and crankshaft sensor on the front side of the engine block toward the driver's side. I have found and engine temperature sensor on the driver,s side of the engine on a housing connected to a radiator hose.
Oddly enough there was an OCV hanging on the harness toward the front driver's side of the wiring harness. Adjacent to this plug is a second plug on a shorter lead that is not connected to anything. Both of these plugs have two leads but are shaped differently oval for the OCV and the other is rectangular. I am wondering if this rectangular plug is for the engine oil temperature sensor? What I cannot see is where the temperature sensor would screw into the head on the front driver's side (near this plug).
I went to NAPA today and they do not have an engine oil temperature sensor listed, but I was able to find one on line. I cannot find a connection point on the head that looks like the picture of the sensor on-line.
View 3 Replies
My check engine light is on. I got the code pulled at Advance Auto Parts. It is P0107 - MAP Sensor Circuit Low Input. I wanted to test the MAP sensor to see if it is bad. I couldn't find anything online that was Santa Fe or even Hyundai specific as far as testing procedures go. I know you can test the power wire, the ground wire, and the signal wire, from what I could tell from other places I've looked. I got 5ish volts from the power wire and 12ish volts on the ground wire, which is what I understand they should be. I don't have a vacuum pump at the moment, but testing the signal wire with no vacuum I got about 0.02 volts. From what I've read online, it should be around 5 volts, but I wasn't sure if all MAP sensors work the same way. Whether I'm doing this correctly and whether they think the sensor is bad?
View 5 Replies
My Santa Fe indicated P0715 for input speed sensor problem. I purchased both sensors and based on forum input I removed the air box and battery to access senors. Output speed sensor is easy to see and access. I am having a problem locating the input sensor. I see wires going to a sensor under both the main wiring harness and shift cable. Is that the location of the input sensor? If so how do you move the wiring harness and shift cable to allow access? If not, where is the input speed sensor located? The Santa Fe is 2001 V6 2.7L.
View 8 Replies
So the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
View 3 Replies
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
View 4 Replies
I went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 Replies
Engine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?
View 5 Replies
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ...
View 2 Replies
I'm getting a weird code on my engine it's p1298 which is electric load detector circuit high input and I'm also getting 3 misfire codes but the car runs great what can I do to fix these.
View 10 Replies
About 3 weeks ago, I purchased a 2001 Accent GL 4dr 5spd from a friend of mine. A few days later, the CEL came on. I went to O'Reilly and got the code pulled, it was for a cam sensor input LOW. I replaced the sensor and was on my way.
Yesterday after starting the car for the first time for a few days (I wasn't driving because it needed a clutch), the light came on. Has it gone bad again or is something causing the signal to be low? Maybe a low output on the alternator or low battery? The interior lights dim slightly when the brake pedal is applied while the car is running.
View 8 Replies
I am getting a p0501 code (off my code reader) on my 2001 Elantra. I have already replaced the Speed sensor on top of the transaxle under the air filter. Driving into work today check engine light came back on and took to AutoZone. They are getting a P0501 code Sensor "A". They had no idea which sensor, sensor "A" was. I know there are 4 sensors on this car and have searched for other posts with no luck, all say replace speed sensor. Need to get this done to pass emissions.
View 2 Replies
Just replaced the spark plugs and coils yesterday, today it gives P0113 code, Intake air temperature (IAT) sensor - high input Wiring open circuit/short to positive, ground wire defective, IAT sensor, ECM...
View 3 Replies
I have a 03 GLI 24v VR6 thats throwing a P0113 code, which is for the intake air temperature sensor. The sensor is part of the MAF sensor, ive tried 2 brand new BOSCH MAF sensors yet the same check engine continues to reoccur. Is there anything else that oculd be triggering it to come on? Is there anyway to bypass/disable it through vagcom?
View 8 Replies
I have a 01 elantra. Check engine light is on. Diags say p0133 o2 sensor slow bank 1 #1. Any way I have replaced the front sensor. Actually now I have 3 of them. The exhaust does not leak. New gaskets on the converter. New flex pipe and everything has been welded.
View 7 Replies
I just had a ton of maintenance done on my 2003 Elantra. Spark plugs & wires, timing belt, drive belts, water pump, replaced coolant and replaced the transmission fluid. The spark plugs are NGK platinum as recommended in my handbook. As soon as the mechanic started the car after the tuneup, the engine light came on with a cam shaft sensor code. He said it went off on its own.
The engine light came back on when I started the car. There's also a major loss of power after coming to a stop. I have to floor it to get it to go anywhere above 20 mph after a stop.
The mechanic said that when he replaced my water pump the liquid splashed all over everything and he thinks he might have gotten something wet that shouldn't have gotten wet and that all will be fine after it dries.
View 2 Replies
I recently took my car to the Hyundai dealer who told me that my engine light was from a bad cam sensor (Fault Code = P0340). I bought the sensor from the Hyundai parts dealer and replaced it myself. After having the code erased, the check engine light comes back on (with the same code) when I turn the car off and turn it back on, after driving it for a while (30 minutes or more).
View 5 Replies
So I am getting a CEL and p0501 (Vehicle Speed Sensor) code and don't quite know how to approach it.
Other forums/posts suggest that I check or replace the input and ouput sensors on the transmission, but from what I understand those are each a unique code, and the p0501 is for a sensor located on the transaxle. Is this the case?
I was under the impression that because my car did not have ABS that I did not have the latter sensor on the transaxle, only the input/output on the transmission. If that is the case, will replacing both eliminate the CEL/p0501?
View 1 Replies
