Elantra XD (2001-06) :: 2003 - Brake Fluid Leak Coming From A Part Near Master Cylinder
Mar 17, 2015
I recently noticed that my brake fluid was leaking in my 2003 Hyundai Elantra and upon further inspection I found the leak was coming from a part near the master cylinder. I looked online and couldn't figure out if this part was part of the master cylinder or brake line or a part all on its own. I tried tightening it but It still leaks some. I read a similar post online and that it could just be that the washer needs replaced but I just wanted to check on here to see what the part is called and if I should just replace the whole thing. I included photos as well.
View 7 Replies
Advertisement
I have replaced the cruise control cut off switch and post-recall pig tail twice in two years for fluid leaks. Whats the deal do they all leak?
View 6 Replies
Early 70's Ford truck. The brake MC fluid is filled but not overfilled, and doesn't leak at all when the truck is parked. It can sit there for a month and never leak a drop, parked. But when I drive the truck, even just around the block, then park, and look inside the engine compartment immediately the brake MC is dripping brake fluid. It appears the leaking mode is by the fluid somehow jumping up and coming over the top edge of the MC when the truck is in motion or when the brakes are applied. All my diy'er years of replacing brake master cylinders on Ford Galaxies, VW Rabbits, Corollas, and this truck, I've never seen this kind of weird brake problem before. On this MC design it seems there's sort of a rubber baffle inside the lid of the MC, and that's present and accounted for.
View 17 Replies
My 2003 Toyota 4 Runner with 104K miles recently started showing a brake light off and on. The brake fluid reservoir was at the minimum level and there was some residue leaking from the bottom near a silver disc. Took it to a mechanic and was told it was most likely the master cylinder leaking brake fluid. Is this normal wear and tear or is it unusual in this vintage vehicle? I do not notice any brake slippage at this point. Should I take this to the dealer and ask why this master cylinder is faulty? I thought Toyotas were long life vehicles?
View 2 Replies
I've got an o2 camry with 150K that seems to be losing brake fluid from the "right" side of the reservoir. Which brake lines are supplied by the "right" half of the master cylinder reservoir? I have read that they could be diagonally piped.
View 14 Replies
I'm getting ready to work on a 2000 Pontiac Sunfire for a co-worker. They told me that brake fluid leaks out where the fluid reservoir attaches to the master cylinder. Could that be a bad master cylinder or something with the brake booster? It looks like there is a lot of sludge in the reservoir.
View 8 Replies
put new master cylinder and bled brakes in 1978 jeep cj5 and now fluid is being forced out the rear brake reservoir in the master cylinder, if lid is off there is about a 1inch fountain of fluid that shoots up.
View 7 Replies
I have a '99 Silverado 250 with a leak between the brake reservoir and the master cyl. Mechanics tell me there is no gasket. How can I get it to stop leaking?
View 12 Replies
Yesterday the brake warning light came on in my 13 350. I checked, and the fluid level in the master cylinder was at the "min" line. I don't think I've ever had to had brake fluid in any car before. Seems to be Ok today, but I was wondering if other folks have had this happen? Of course if it happens again I'll have to check the brake system. Just wanted to check.
View 8 Replies
I have power steering fluid leaking out of the bottom of the Brake master cylinder out of a round hole. Every time I pushed brakes it leaks a good amount of power steering fluid out. Why it would do this and is there a screw missing out of the hole or what?
View 6 Replies
Just wanted to report another F150 with the blown master cylinder problem and had a few questions regarding the issue. Its a 2014 Screw EcoBoost with about 12500 miles located in Michigan.
I was driving last Friday (6/19) when the low brake fluid dash lamp illuminated. I made it to my final destination, when I began to back into a parking spot the brake pedal dropped to a position about an inch off the floor. Parked the truck and popped the hood to find almost all of the fluid gone. Only having fluid in the rear axle reservoir of the brake circuit. Pulled the vacuum sensor and the booster is filled with fluid..
Called Ford, had it towed to the dealer and its been sitting there ever since.... They have no loaners and have not even looked at it yet. I'm going to assume no parts are in stock just like all of the other threads I have read on here about this issue.
A few questions I have for those of you who have had this problem or have knowledge about it.
1. How long did it take for your truck to be repaired?
2. When the master cylinder seal leaks all of the fluid into the booster and the booster is pulling engine vacuum; does this mean that brake fluid is then pulled into the crankcase of the engine?
Really looking to get my truck back soon cause I love driving it! But the '74 F250 will have to do for now ....
View 14 Replies
I had this sad puppy noise coming from my brakes so I have now replaced my brake booster. When doing so I took my old brake master cylinder and put it on my new brake booster. When trying to bench bleed it it only came fluid from the P marked circuit. It came no fluid from "S". I guess it stands for primary and secondary.
I thought it was because I couldn't press the piston hard enough so I installed it in the car so I could use the brake pedal to get more power. But still no fluid from "S". Is the brake master cylinder faulty? The rear discs are unevenly worn.
View 1 Replies
2001 F-150. I've got a leak around the warning switch and can't seem to find info about replacement. Is the switch and switch retainer screwed into the reservoir or is the outer ring screwed into reservoir and more of a compression type fitting that holds switch in place? Also, after removing and repairing will bleeding be necessary? Looks like everything I'm taking apart is above fluid level after I siphon enough fluid from reservoir to replace fitting.
View 2 Replies
Just purchased a 2003 GX470 with 160k and after the low brake fluid light came on I noticed the master cylinder had a leak. After removing the cover it appears the fluid has leaked for quite some time as the paint has started pealing from the frame. The brakes however appear to be working correctly. Upon purchase the front calipers were seized and I replaced both front calipers.
After having someone depress the brake pedal while I watched, the fluid leaks from the end of the master cylinder each time pedal is pressed in.
After doing some research it appears there is a rebuild kit for the master cylinder.
View 3 Replies
...Is there anything special that needs to be done for brake bleeding after putting in a new master cylinder? I decided today to flush my system with my vacuum bleeder and now my pedal slowly falls to the floor at a light...No problems in a panic stop or otherwise, just falls to the floor slowly when braking...no leaks, so I'm assuming a master cylinder is an order....
View 14 Replies
I tried to replace my brake master cylinder today but wasn't able to because of a plug
It's the black plug on the drivers side, the connector is upside down so I can't see how to unplug it I tried for an hour then got too frustrated I had to come inside
My Haynes manual says "unplug" obviously
View 1 Replies
ll, I changed out the master cylinder on my 2002 F-150, disk brakes front and back w/ ABS. Bleed all the air out and bench bleed the master cylinder. I have good pedal but the brake light will not go out.
View 6 Replies
A few years ago I (for him) replaced all 4 calipers, rotors, pads, etc....things were good. Just recently he replaced his Brake Booster and Master Cylinder (not sure what led to this), but long story short everything is back together and he doesn't have brakes.
My GUESS is that the system needs a good flush, new fluid, etc....
My problem is I'm unsure how to bleed the ABS system. A few google searched indicate I need a scan tool, but is there another way? Can I jump something.
So my question, how do I completely bleed the brake system on this truck?
View 7 Replies
2001 F-350 / 7.3L / 147K ... What are some symptoms of the master cylinder going out? And is there a such thing as a rebuild kit anymore? The pedal has been getting spongier & spongier over the past months. Truck still stops O.K. but you have to brake earlier than I used to. Pedal can go almost to the floor. Pedal continues to go to floor as pressure is applied. Does not go to floor though.
View 4 Replies
What kind of brake line is it and if is replicable with regular brake line? I'm just replacing long line between front and back splitter block and just would like to know what is it. What is purpose of that braiding (?) at front brake lines and why they wind down instead of going straight. Part of that long line is braided too, part that go across frame.
View 3 Replies
I have replaced booster, master cylinder, all four callipers, and bled the brake system a number of times on my 2000 F-150 4x4. and still the pedal is wicked spongy, is there some other problem?
View 6 Replies
