Elantra MD (2010-15) :: License Plate Lights Keep Burning Out?
Jun 13, 2014
For a few weeks now I noticed my stock license plate bulbs started to act strange. My left one is about half burned out, and the right one started to flicker and burned out entirely.
So.. Easy fix right? I bought 4-smd led lights to replace the burnt out ones and as soon as I installed them they worked perfectly! But about twenty minutes later .. The right one burned out. And the left one is dim.
Is there something wrong with the wire? what can I do?
View 6 Replies
Advertisement
So I bought LED license plate lights, the same ones Track5tar has (who sent me the link to get them). I got em off the bay, and I put them in and they don't work! The Heatsink gets hot but the lights don't light up in both of them!
View 24 Replies
So I was replacing the lights with the new leds change one toke some pics to compare. Everything fine...
Removed the other feston put the new led and they won't turn on anymore..
Change them back. Put them upside down, up, sideways... Nothing
Check all three fuse boxes all ok
Every other light on, inside trunk on, side markers on...
Everything but the license plate lights.
View 12 Replies
Bulbs are fine, I turned the light switch from off to on (12 o'clock position) and they flicker for a split second. What can be wrong? I checked the harness on the rear hatch and it looks fine. Maybe the switch itself?
View 2 Replies
I have a Ford Windstar 1999 . My license plate lights are both out. I remove the inside panel of the back door, there is a connector between the license lamps and the rest of the car electrical system. I disconnect it. I go turn on the lamps at the dash board, I then reconnect the connector to the license plate lamps at the rear door… and they work! I go back to the dash and switch the lamps (controls side +rear lamps and license) OFF and then immediately back ON, and the license plate lamps stay OUT. All the others lamps on the fuse circuit work fine. When lamps are lit, shaking the wiring harness has no effect. What is happening and where? This is very strange!
View 4 Replies
I have a 90 Honda Accord and can't figure out why the lights aren't working. I have no computer codes and all the fuses are good. The headlights, brake, turn signal lights, hazards and interior lights work fine but the tail lights, license plate lights, and all marker lights won't go on. I only noticed by a chance walk around on the car. I've checked every fuse inside and outside fuse panels. The hazards and brake lights going on makes me think that it can't be a ground problem.
I have spent a lot of time trying different things and checking wires andd fuses and can't find any problems. Is there a relay or something for the marker lights?
View 14 Replies
Where the license plate lights get thir power from? I have a 2002 SC430 and the plug is just dangling. It goes behind the plate and then if I look under the car, it is just there by the bumper and I cannot find a connector that it can reach.
View 3 Replies
One of my license plate lights doesn't turn on until I tap it..
What could be causing this? I installed LED's in them but a few months later I noticed this happening.
View 7 Replies
I try to install LEDS on it and I guess I accidently blew the fuse and when I try to search for it, I can't locate it.
View 3 Replies
Was installing led license plate lights and they turned on for a second then shut off, I began trying to switch them around and do whatever I could but still wouldn't light up even put the stock ones in again and they wouldn't work.
View 8 Replies
My Pathfinder has the license palate in the middle/center of the hatchback door, with one light on the left and one on the right. I cannot figure out how to change the bulbs and my manual is no dice; it shows the process for a different location of the plate on the door, maybe a different version of my year model.
View 6 Replies
I am planning on adding fog lights to my Corolla 2011 LE.
I am considering this one ....
and these LEDs for my license plate ....
View 1 Replies
After going through the car wash several times now in my 2010 RX 350, my front license plate has been bent in all different directions. Car wash guys say it's due to not having a full plate holder, where as 4 screws secure the plate vs. only the top 2 as we have. Any plate holder from another vehicle that I might adapt to overcome this?
View 14 Replies
So my tail lights and license plate lights are not working. The head lights work also my gauge cluster lights are not working. Which fuse I should check. Or what it might be?
View 6 Replies
I wanted to change my license plate bulbs to LED's. Can't figure out how to get to them. The book says have the dealer replace these bulbs if burnt out. I Always like to try to do things myself.
View 7 Replies
I have a 2010 RX450h and live in Minnesota where it is hard to hand wash my car. The darn car washes tend to catch the front of my license plate frame and bend it and the license. I have tried several different plate frames and none worked. Minnesota plates are now the thin, non-stamped plates so they are very flimsy.
I even tried putting a plastic plate behind the license to make it more rigid but that failed too.
View 1 Replies
How to change the license plate light bulb for lexus rx 350 2010.
View 4 Replies
I was just washing my 2016 superduty that just turned 3000mi and noticed the light housings and plastic are broken on the license plate lights. The one just fell apart in my hand. 55k and this happens at 3000mi.
View 9 Replies
Replacing license plate bulb on a 3rd gen rx? I tried taking off the interior lining on the rear hatch but no luck. There's access covers for taillight & reverse, but none for license plate light. I also tried "popping" out the plate light cover right above the license plate... don't think they are designed to be popped out.
View 3 Replies
how the chrome trim above the rear license plate is removed?
View 4 Replies
I'm having some sort of electrical malfunction on the back of my Mk4 Gti. The right rear tail light, license plate light and back windshield wiper doesn't work. I replaced the bulbs several times and they keep blowing.
View 2 Replies