How to install load resistors in the front turn signals to fix fast blinking after led changing? I have two 6 ohms 50 watts resistors but I don't know how to install in the front turn signals.
View 7 RepliesI made the conversion of the regular bulbs to led ( stops, position, turn signals ) but I have fast blinking in turn signals. I know that the led has fewer electric resistance than the regular bulbs so the car takes this like a damaged bulb.
I know two possibilities:
1- A resistance for each one of the led to confuse the system.
2 - Changing the electronic relay
I don't know which one is better. I need a resistance for each bulb? which relay is the appropriate one for this car (there's a lot of references on the internet and I can't find the relay in the hood's car).
How to fix or solve front turn signals that are not working? I just realized that both the front signals on my Prius doesn't light or flash when making a turn, the rear are working fine. Is this an easy fix or should I bring it to the dealer?
View 4 RepliesHow do u remove and install the turn signals in the mirror?
View 6 RepliesVolvo XC90 T6 AWD (2004) Changed my battery and now my turn signals won't work, won't show from display panel (interior) or light up (exterior), and my fog lamps are also not working. Used a memory settings save backup and checked fuses but can't figure out what's wrong. Electrical worked fine before battery change. Battery was aftermarket (non-OEM).
View 2 RepliesToday, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
Over the past few days I've been working on the car, a Canadian 2014 Elantra L 6-speed, in an attempt to install the keyless entry system into it.
- I found a wiring diagram online and for the most part its been working, gotten the tail lights/siren and just about every feature working excluding the doors themselves locking and unlocking.
From what I can tell, in order to get the mechanism to operate correctly a relay is needed and needs to be hooked up into, correct me if I'm wrong as the car isn't with me currently, Plug A and B (59 Pin and 24 Pin). However no matter the amount of configurations I have tried, it just will not work.
*Do not care for the trunk opening operation.
**The system I currently have is a Spy la-3 Pke keyless system.
I just recently put a jl8"w7 in my truck and this thing make my car rattle like crazy not just the trunk lid. The worse part is the rear deck below the back glass, any quick fix before I start tearing things apart?
View 4 RepliesMy mk4 jetta is causing me a hell of a fuss right now. The rear turn signals and the signals in the fenders are working but the front signals are both out. The signals blink fast as if it's a bulb but both bulbs and all fuses are good. When the hazards are on, they blink normal speed but the front lights are still out.
View 13 RepliesI installed my dome light, map light, and rear license plate LEDs with no problem a couple of months ago. When my LEDs for the vanity lights came in today, I immediately went to install them. The first one on the driver's side was installed without a hitch, but after I installed the second one on the passenger side, none of the interior lights worked. The only difference in installation I can think of is that I disconnected the light on the passenger side as opposed to keeping it plugged in on the driver's side.
View 6 RepliesSwapped out the front turn signal bulbs for LEDs? Looking for pics or vids showing the difference between LED and stock.
View 17 RepliesI disconnected my DRL's (because I have HID's so they don't work) so I am currently using my parking lights (front turn signals, rear brake lights) as my DRL's, however my problem is that the front turn signals are not that bright, so what I can do to make them more visible during the day...
View 24 RepliesI am gonna switch out my front turn signals from my 2006 Passat but I dont know how. Are there any screws or clips that I need to remove? Looking for Pics ....
View 3 RepliesOk so I have a 2014 F-150 Screw fX4 with the projector headlights. 13356.0 km as I sit in it. I had turn signals the other day, but now none. I had the dealer disable the lamp outage to remove the hyper flash issue with led's. Sockets don't look burnt or anything everything is new. So here is what is working.
- mirrors turn indicators
- rear turn signals
- dash turn signals.
I have reinstalled my OEM bulbs and still have the issue, only my running lights are on the front. So it has power.
Below in this photo-shopped picture the camry headlights have clear reflectors for the turn signals ..
I am going to be doing a HID retro , and I want to swap out my reflectors for some clear ones. Anything or anyplace I can get large non-vehicle specific reflectors and i can manufacture my own ? I want to keep the car as legal as possible, after my illegal retro (all retro's are illegal )
I have LED bulbs for the rear turn signals but will need to replace the relay so I don't get the fast blink. Where is the dam thing and how do you get to it to replace it?
View 4 Replies1996 Mazda Protégé, 128,821 miles, in town driving 5000 miles per year in recent years.
I hit the frame of my garage door about 6 months or more ago which partially pulled off the front bumper area and knocked the right turn signal lens and headlight out of whack. My handyman fixed it up, by using good quality baling wire so the turn signal and headlight etc worked.
Then, I did the same thing a couple of weeks ago. (I was trying to avoid hitting my bicycle which I had just had reconditioned for an ungodly amount of money) My handyman is unavailable to fix it again. I have gotten stopped once by the police for the malfunctioning turn signal so it was time to get it fixed.
Mechanic (same one as previous posts) said it will cost 1500 to replace the bumper area etc so the front turn signals will work. He absolutely insisted that the turn signal wires cannot be reconnected. He reattached the bumper area "temporarily". I am willing to pay to get the turn signals functioning but do I need to replace the whole bumper assembly unit?
Does this seem plausible?? I just want the turn signals to work. I do not care about how it looks. (I drove the car in the interim with a bright yellow bungie cord holding the unit together)
1999 F250 super duty. I am having a problem with the front right turn signal not working. The indicator on the dash also does not work but I can hear the relay clicking double time and the rear signal works. I have changed the bulb and fuses and went under the dash and the column to be sure a connection had not come loose. I have looked through the forums to try and find an answer with no luck. What to try next?
View 4 RepliesI have a 2003 Excursion 7.3 2WD Limited and all of the sudden experienced a number of issues all at once.
1. Turn signals stopped flashing (hazards still flash)
2. Lost Rear back up sensors
3. Lost overhead trip computer
4. Lost Rear A/C - switch does nothing
5. Front A/C now only blows through the defroster vent
I've checked all the fuses and cant find any bad ones.
I replaced the multi-switch flasher and turn signals still dont work - only hazards.
I found out last night that all 3 of my brake lights are out. However, my tail lights work, and my turn-signals work. So obviously its not a big wiring deal. I was looking for the brake switch but i don't know where its at because i looked underneath. What fuse is the brake lights cause my manual doesn't have it listed. I drive a 04 Elantra GLS.
View 6 Replies2010 F-250 14,000 miles, gas engine with Knapheide utility bed. Tilt wheel has been kept in the up position from day 1.
The problem:
No rear brake lights.
No high mount brake light.
No rear turn signals.
No rear hazard flashing lights.
All trailer lights work.
All other truck lights work.
Things checked: Fuses all OK. Visual inspection of multi-function switch. Looks clean. Brake switch at brake pedal has power on one wire. Jumpered the other wire-no brake lights.
I need to haul my trailer and am nervous when I see a Savannah, GA metro police car.