I recently purchased a 2013 elantra.
I have noticed that there is engine vibration and noise felt in car and pedal when accelerating at around 2500-3000 rpm's before it shifts. Is this normal behavior? It just does not seem as smooth as it should be. I have only put about 600 miles on the car.
It has been very cold, but it does not go away after warming up.
I've been getting a blinking engine check light.. I pulled all the codes:
P0050: H02S Bank 2 Sen 1 Heater Circuit
P0155: O2 Sensor Heater Circuit Malfunction Bank 2 Sen 1
P0304: cylinder 4 Misfire detected
P0688: ECM/PCM Power relay sensor circuit
I've had the car sitting for awhile because I lost my job and didn't have any money to roll it around much.
I just changed out the spark plugs and two of these had a white coating on them.. I was hoping this would take care of the misfire after I replaced them. I also bought a new battery because mine had lost charge a few times.
The Car will run with an engine check light, but if I go past 2500-3000 rpms then it will start blinking (which means don't drive it )
The oil has been sitting in it for about 2 months, so I'm about to go change that and I'm hoping this will allow me to drive it without issues.
Any of these codes thrown and know what they could be? Which O2 sensor (like a link to a website that sells them). Trying to get this thing running again.
At the beginning December I put my brand new winter tires (general altimax arctics) on the factory steelies and put them on the car gearing up for the snow. Not to long after the install I notice that I was getting a very strong engine vibration starting at 3,000 rpms and it stopped around 3,100 rpms no matter what gear I was in. At first I though it maybe just the cold affecting the engine. Well...
Last week I put my summer rims and tires back on for the 1,600 mile trip to MO and back, and like magic, no more heavy vibrations. Smooth acceleration throughout the normal driving rpm range. I just changed the oil and tranny fluids Tuesday after we got back and with the warmer weather the car is running smooth as silk. Still an awesome car with awesome mileage and couldn't be happier.
I bought a new 2014 Elantra last Monday. Around 100 miles (Wednesday) I noticed it was making a ticking noise when accelerating. The sound gets louder at higher RPMs and goes away when I get off of the accelerator. You can't hear it over the radio but it's embarrassing when my passengers do. It almost sounds like a puff of air escaping or something, similar to a go-kart engine lol.
Anyways, I took it to the dealer Thursday and they drove it and said the noise was normal during the engines break-in period and if it persists after 15k to bring it back and they would see if there was something that needed tightening.
I have a 2000 b5 wagon with a 2.8 5spd with 200k on it .... Its slammed on coils and i get this squealing in reverse i dont know what it is i just rebuilt the front end ie control arms... also have a nasty vibration from 1000rpms to 3000 rpms could that be engine mounts/snub mount?
View 7 Replies2002 Elantra engine is revving up to 3000 rpms when in neutral or park. I changed the Throttle Position sensor and it went right back to revving up. Code read P0121. What might be causing this? Seems like I get one thing fixed and then another code shows up..
View 2 RepliesTruck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
Had a first-time issue with my car today. Background, 2010 II bought in June, just short of 15K miles, never had any kind of mechanical issue.
While en route to work this morning, I was about halfway into my 15 minute drive to work, when I noticed my engine was idling very high, I would guess 2500 rpms. It started doing it while I was driving around 35 MPH, then continued doing it while I stopped at a traffic light, and continued when I continued driving to a speed around 50 MPH. The high idle while stopped was not transferred to the wheels, so it was not a safety issue as it would be in other cars.
When I got back up to 50, curious to try something, I hit the ECO mode button and the car returned to normal. I took ECO back off and the car was still fine. I had no further problems.
I would point out that this morning was about the coldest temp that the car has experienced. Outside temp ranged from 7 to 10 degrees.
When I accelerate (particularly during heavy throttle) I hear a sound that sounds like a diesel engine between 2000 and 2500 rpm's. It almost sounds raspy in nature.
View 24 RepliesHave owned a 2014 LS460 since April. Ever since then, when accelerating decelerating between 1000 and 3000 rpm, we hear a whining and grinding noise.
View 9 RepliesThe rattle, 1.8t GLI
-2500-3000 RPM
-Car can be in gear or out of gear, rev rattle is the same.
-Sometimes, I can hear the rattle when the car is off and I slam the door slightly harder than usual.
-My hood release cable may have been the culprit, but I could only zip-tie part of it and the rattle hasn't changed.
One really important clue is that when I have reached around the area between my engine and airbox, the rattle has gone away. So I had a bad coolant flange, so when reaching my phone down there to take pictures, I must have bumped or pressed something because the noise was gone for about a mile.
I recently had my airbox out and a visual inspection didn't show any promise and tapping on random parts didn't recreate the sound.
There is am RPM rattle near my airbox....
On my drive home today around 2500-3000 rpm I am getting real bad lifter ticking noise. When I let of the gas it stops but as soon as I get back on it it will start ticking again. I just bought oil for an oil change Mobile 1
0W-40 I'm pretty sure plus a mobile 1 filter. Will this stop the ticking noise or do I need to adjust my lifters?
So I bought this 2007 used with 86K on the engine. After 2 days cats code went off and i had both replaced with brand new ones. Now my truck is making a rattling as i step on the gas at about 2500 rpms. Its sounds like metal in a can swirling around amd as i let off gas the sound stops. It happens often, also the other day in was pulling off and heard a grind for about 2 seconds then stopped never beard it again, it sounds like its coming from the rear passenger side. It sounds like a bearing. This is the noise.
IMG_4285.MOV ...
I have a 2003 Camry 2.4 LE with 120k miles on it. It's been very well taken care of. As of now, here is the maintenance that has been completed at my dealership. By the way, I don't trust dealerships, but I do have one nearby that is actually beyond outstanding (and I know a little about cars):
- Regular oil changes, and always with 5W-30
- Radiator flush and thermostat replacement
- Tranny flush
- New front brakes, rear brakes cleaned, and lines flushed.
- Oil pan gasket replaced
- Valve cover gasket replaced
- Spark plugs replaced (at around 105k)
So, with this information being provided, here is my current problem. Lately, as I accelerate between 1500-2500 rpms, the engine has a louder than usual (but not too loud) groaning noise. Basically, the engine just sounds a tad louder than normal along with groaning noise. The engine also feels as though it is running kind of "dry" (if that makes any sense).
Now, above 2500 rpms, it's just fine. It's amazing on the highway, but I feel as though it has slightly lost acceleration in the city. The only issue with the car is the infamous greyish/blue smoke at startup, but that rarely happens and when it does, its a small amount of smoke, and it has never affected it's performance or gas mileage. Another thing is that I had to have that dreaded oil splash guard removed, because apparently the timing chain punctured it and it was about to fall off.
This problem has been recent within the last month. Just before this, the car has been on a roundtrip to Tucson from Tulsa, and Amarillo twice, complete with 32+mpg on the highway! So, what's wrong? Serptentine belt? PCV valve? Cam or something underneath the valve cover?
I test drove an 08 VR6 Touareg 2 this evening. Felt quite nice though I even with the upgraded V6, I found myself stomping on the gas on the freeway to overtake compared to my 05 V8.
Anyway, what I wanted to post about was a vibration type noise occuring just around 2500rpm in 2nd and 3rd (and possibly others) when accelerating. At first, I thought it might be something in the muffler, but I wound down the windows and it didn't seem to be coming from the outside.
Note that the sound was not any kind of throaty roar - it sounded like something was loose/vibrating. Hopefully this is limited to the particular example that I drove?
MT 2500 Where are you I've got a weird one. 99 Chevy 5.7 dully dump truck. The engine cuts out while driving at 3000rpms only. If you keep your foot in it it goes away at 3200. Does it in any gear(auto). Also, stopped and in park, it will do it at 4000rpms. Acts like a rev limiter. Fuel pressure does not change (60-62psi) when this happens, does it in open or closed loop. I disconnected the maf and no change. I've installed new cap, rotor, plugs, wires, coil, module(all original with 165K), no change. Runs sensational until 3K rpms.
View 14 RepliesWhen the engine is in gears say 1-3 (doesn't seem to work in neutral or park) when the engine rev's to about 2500 - 3000 RPM there's a metallic vibrating noise that almost sounds like a buzzing/chattering sound. When you reach over 3000, it goes away.
Here's the curve ball - it stops doing this when the engine is really warm. It only seems to do it when cold or it's been sitting a while. So - it's limited to an RPM range between gears 1-3, it goes away when it's warm.
I am inclined to think this is related to engine mounts... And here's why. It seems to only happen when in gear and we know that the engine changes it's pitch/stance when in different gears versus in neutral/park. So I think when it's in gears 1-3, the engine is tilted a bit and something is coming into contact with something (maybe my strut bar) more than it used to due to more slop/movement from my worn out engine mounts. As to why it goes away when the engine is really hot (driven for an hour or so) is because maybe whatever it is that's coming into contact with something else is (perhaps a hose and its clamp?) is much more pliable while warm and clears whatever obstruction it was hitting while cold? (a lot of speculation and creative thinking here).
Anyway - after the engine is super warm and I've been driving it I cannot for the life of me get it to do it... It rev's super smooth and not a hint of any bad sound.... 2011 2.0T Limited ....
I've got an automatic transmission 2002 elantra 2.0 that I purchased in 2009. About a year after owning it a weird problem developed that I've just sort of lived with since. Between 25-40 mph my RPMs occasionally "bounce" persistently by an amount between 500 (mild) and about 1000 (severe). There's a bit of fluctuation insofar as what RPMs/speeds it happens at depending on outside temperature and how warm the engine is (higher temps correlate with this issue happening at higher RPMs and a more pronounced fluctuation), but it's a consistent issue every time I drive. It *seems* like my car is always trying to push down the revs, hits a certain low point depending on the gear/speed, then jumps up just a bit only to edge back down. Lather, rinse, repeat. It's not simply a display problem as I can feel and hear the engine revs changing.
No fluctuations at idle. Above 3000 RPMs it's ALWAYS smooth sailing. When I'm actively accelerating there's never a problem, even if my acceleration stays in the revolution problem range. The car is never in danger of dying, but if the cruise is engaged (ESPECIALLY in the 25-30 MPH range at operating temp) the car shudders uphill - I assume this is because the RPMs dip a bit too low for the gear the car is in. If I press the throttle the car responds normally. This bouncing RPM issue itself NEVER causes the car to shift gears in response, and if it's happening and the car DOES shift everything works fine until it goes back to trying to maintain RPMs in the problem range. When it happens I usually just increase speed by 5MPH and it goes away, though if the car is warm and the speed limit doesn't allow me to go fast enough to get out of the problem range it just does the same thing at the slightly higher RPMs.
When the problem started my car threw an OBD code - I didn't read it myself and brought the car to a random service shop who SAID they changed the throttle position sensor, and the code was gone, but a few days later it was doing the same thing without throwing a code. I tried changing the fuel pump thinking it was a fuel delivery problem, but that didn't solve anything. I put seafoam in the fuel system monthly so I'm fairly certain that fuel system gunk isn't an issue. The symptoms haven't changed AT ALL during the 6+ years this has been happening.
The kicker is that a few years ago I found a SUPERB mechanic - the first one I've ever actually trusted to be not only competent but also honest. Described the problem and even demonstrated it to him. When I brought in my car to have the struts and mounts replaced he spent two days trying to figure out what was causing the RPM issue too... and couldn't nail it down.
Possibly related: after starting the car - regardless of how long it's been running - there's a brief delay between pressing the gas pedal and the engine responding. Delay seems *slightly* longer the colder it is outside, but it's never more than a second and a half. No further delays unless I shut the engine off and turn it on again. Replacing the fuel pump didn't affect this matter whatsoever.
I drive a 2008 Elantra automatic,and have a constant engine shudder/vibration whenever the rpms are between 1000 and1500. The engine shudder stops as soon as I accelerate above 1500 rpms,or take my foot off the gas completely.
The dealer recommended cleaning of the fuel injector system,not sure if thats the course to take.I do know my model has had fuel pump issues,but the dealer has told me all recalls on the car have been processed.
My 2012 Elantra has been nothing but problems. Unfortunately, with me being away from home in the USA, I haven't been able to bring it to my dealership. Lately, I've noticed that the acceleration of my E sounds different with the A/C on. It's more noticeable right when I hit the throttle that the engine engages, and power goes to the wheel. The sound is a deep more drone like sound, and is only there when my A/C is on.
View 8 RepliesI have a 01 b5.5 Passat. When I'm in tiptronic and I'm about to hit 3000 rpms, a really off noise goes off and it's like a grinding sound.... Like when your car doesn't want to go to the next gear!
View 1 Replies