Elantra MD (2010-15) :: CEL Flashed / Engine Began Misfiring
Apr 25, 2012
So yesterday my car flashed a CEL so today I got it checked out early in the morning and the SA told me that my car had the old Engine Software for MY2011 Elantra's so the dealer updated it to the newest one with the TSB and CEL was gone and I was off with a newly washed car.
Then this afternoon my car the dilemma started after I picked up my friends kids. When I started my car, the engine began misfiring to the point it barely starts I even tried revving her a lil bit but to no avail. I had to drive it to the nearest parking lot since I was parked on the street but the engine was not cooperating at all. Good thing she let me move her a few feet away just to be in a safe zone with the kids.
Called my SA and told him about the problem and he told me to call Hyundai Roadside to get my car towed. 30mins later car was at the dealer but tech's are gone for the day so I had to leave my car. The dealership was kind enough to give me a rental until I get back my car. For now I'm driving a 2011 Nissan Sentra (base model) I'll update you guys tomorrow of what happened with my car.
View 12 Replies
Advertisement
I just started to have some idle problems with my 2013 Elantra GLS auto 1.8 that has 10k miles.
I went to the gas station to fill up the tank since the gas was very low (30 mile range). I filled up the tank, started the car and the engine began to stumble and idle poorly like it was about to stall. I put the car in drive and the engine stalled. I restarted the car and it ran normally.
The car will now briefly idle poorly when I'm at a stop light. The car will be at a stop light idling and running normally. Suddenly, the tach will go down to 200 rpm and then up to 1200 rpm, like it is about the stall. Then it will idle steadily and be back to normal. This has happened about three times over the past two weeks.
What may be causing this intermittent idle problem?
View 9 Replies
engine light came on 3 days ago....engine/transmission seemed to be "misfiring" a bit.....engine light went off after 3 days.....took in today, computer says some "transmission sensor/module" not working properly.....will take 3 hrs to repair but warranty covering it.
View 7 Replies
I am starting to have an issue with my 2012 auto transmission Elantra that just passed 100k miles. When under mild acceleration, as when gently leaving a red light accelerating to 45 mph, I can feel a distinct chugging as if a cylinder is randomly mis-firing once or twice a second. This is never felt during coasting with no power applied. It is also not apparent during full throttle or aggressive acceleration. Only during casual daily-type driving. Now I have had other cars in the past that once in a while would throw a CEL code if a cylinder mis-fired, but I have no Check Engine Light on. This leads me to doubt a mis-firing plug. What could be the cause of this?
Other possibilities would be perhaps the auto transmission is somehow momentarily interrupting power to cause the mis-firing effect??? Is that possible? Perhaps the fuel pump is going bad and getting intermittent? But then why is all good during full throttle?
View 28 Replies
I just bought my wife a 2010 GX 460 and noticed an issue today with 4 Lo. When sitting with the car on, and in park, I engaged 4 Lo. The 4 Lo light began flashing along with a dinging sound. It didn't stop when I put it in drive or reverse, and just continued. The manual states I need to take it into the dealership because there is a malfunction.
View 10 Replies
Basically, my high beams work when flashed (pulling the lever), but they don't work when I want to leave them on (push the lever). It's obvious that it's not the bulbs since they work when flashing. I'd really like to avoid taking it to the dealership since the Lexus dealerships in my area are notorious for overcharging their customers and not doing a good job.
View 7 Replies
My question: was there some some OBD code or light I should have expected (that didn't show)? What did the flashing Check Engine Light mean?
At 10:30pm last night, I picked my wife and bro-in-law up from the Logan airport, and on the way to drop BIL at his house, I saw a brief whisp of steam/smoke rise from the passenger side hood/wheel-well when idling at a top-light. I exclaimed that the car was smoking, but BOTH my wife and BIL insisted that we had been stopped over a steam grate. (In 70 degree weather? I puzzled, but since BOTH said that had been the case...).
A few minutes later, the check-engine light flashed (three times, I think) and then went off. I drive with an OBD ScanTool attached on the dash, so I immediately switched it to scan the codes, but it reported "clear" / no codes! Either immediately before or immediately after, the car lost accelerating power for 1 or 2 seconds (at most), but then resumed normal driving. No other dash lights were on, though I did not look at the temp gauge.
I am a former chef and professional cook, and have a VERY sensitive sense of smell-- there was NONE; I watched attentively, and the absence of further smoke/steam seemed to support the unseasonal steam-grate hypothesis. I had also picked up the car within the last 24 hours from THE HONDA DEALERSHIP, who I had asked to look everything over to ensure another 6 months of problem-free driving. (I rejected their offer of a $249.00 "triple flush" of transmission, brakes, and pwr steering.) We have otherwise had zero problems with the transmission or cooling-- the car is old, but maintained reasonably well and driven less that 5000 mi / year. Boston driving, but not aggressive or 19 years old!
No further thought, as all seemed okay except for the brief "blip", and pregnant wife, brother-in-law, two dogs, and I all wanted to get home.Drove the 2ish miles to our apartment, with no further blips. At a stoplight about 3 blocks from home, a LOT of smoke/steam started coming out from the hood. Still no lights or OBD codes! At that point, I pulled over within 5 seconds, and noticed that the temp was pinned or nearly so (If there is supposed to be a light on the gauges, I had it all the way dimmed). Looking under the hood, the spray pattern on the hood insulator made it easy to find the split in one of the hoses connected just under the distributor (about 1.25in OD; I'm guessing coolant or transmission, based on the symptoms??).
While waiting for a tow-truck (since I wasn't even sure if it would do any damage to drive the remaining blocks to my driveway), and after things had a chance to cool a bit, my wife restarted the engine for a second so I could check if any additional fluid came out of that split, but none did. Once the temp was back down towards the low end in 20ish minutes, I drove the car about one block so I could stop blocking traffic-- it drove fine, and the temp didn't visibly rise in that 200 yards. Still, the CEL was not on (or flashing) during startup or while running, and there were NO OBD CODES.
View 4 Replies
Check engine light flashed for a very brief period, car ran very rough, and then check engine light (exhaust system malfunction) stayed lit. Took to dealer this AM and service advisor asked that I bring it back on Monday morning (loaner promised) but in the meantime, I could continue driving it unless the engine light started flashing. Car is now running okay, but last night it seemed to be running on only 6 or 7 cylinders. Only 93 or 94 octane gas is used and I've owned enough German cars to know how the gas cap should be tightened. Seemed like an oxygen sensor malfunction last night but now I'm not certain.
View 15 Replies
It was pretty warm this afternoon, had the AC on full blast. Drove into a left turn lane and stopped for the red arrow, the engine began spurring for a couple seconds. Then it caught itself but afterward felt the whole car shake for like a minute, drove off once it was a green arrow and nothing else happened. Has any one else had this or a similar experience happened to them? My Camry just hit 30k miles, I wonder if it just had a "spaz" (or whatever you want to call it) attack.
View 4 Replies
When I was driving back from hunting on a dirt road riddled with pot holes and washboard. I came around a corner, hit a pothole and that's when bad things happened. The headlights flashed once and then completely cut out and wouldn't turn back on even after the car came to a full stop. Right after the headlights cut out the engine shutoff and refused to start again. When I turned the key to try and turn the car over all I got was the click, click, click (repeating) from the starter. This happened on a 94 geo metro with 193,000 miles on it.
View 6 Replies
I have a 2001 Volvo S60. I just got in it to go to the store and I swear it is possessed! My engine immediately began shaking and rumbling the idle went from very high to dangerously low. I cut it off and cut it back on. There was no rumbling but now it is idling very high close to 3.5 rpm when it does settle after a while if i even touch the gas a little it shoots right back up. My emission error message is showing but i have had it looked at a few times and they can't find anything wrong with the emissions system. Recently my transmission message came on and stayed on for a week or so but went back off before I could have it looked at and it never drove any different even when the light was on
View 5 Replies
I was driving my car when suddenly I felt a huge shudder and my engine light flashed on. I turned a corner to head into a parking lot and as I accelerated my car seemed to be jerking like it was cutting out. I parked and tried revving it and it sounds all deep and gurgly not smooth. What could be wrong and is it safe to drive the 5 miles back to my house.
View 4 Replies
I got a 2013 Turbo. This morning I gave it 90% throttle and I got shaking, check Engine light flashed on and stayed on until I layed off the gas. It drives fine under regular throttle, but for ie. Passing someone on the highway.. Yeah ain't happening, idk if it just won't downshift, or the turbo is acting up.
I have an Injen intake and Had it installed since day one or two of ownership. Bought the car brand new, it has 43k miles, and I usually give it WOT a few times a day ()
But it's weird how all of a sudden it's doing this, I tried restarting the car, leaving it to rest for a while and same result. I personally think it's the tranny not being able to downshift, even holding a gear at high RPM, it shakes. Turbo sounds like it's working fine but who knows what's going on under the hood.
View 4 Replies
I have a 2002 VW Golf, with 203,000 miles on it. The check engine light is already on because the cat has worn out. I'm saving to buy a new one. However this morning about 5 minutes into my trip to work my check engine light flashed a few times. After pulling over and turning around to go back home the flashing stopped and the check engine light went back to be solid. Could the worn out cat have caused that? The car seems to run like normal. I did feel a little something when the light started blinking, but then it went away. The dealership and my regular VW mechanic have both said that the car is safe to drive regarding the catalytic converter until this winter when I get my tax return back. I have very little money right now for a repair. I should have more in a couple of months. The only thing that has caused the check engine light to blink in the past was the ignition coil pack. The car is on its third one and I know that feeling, this wasn't it. Plus I just got a new coil pack in June 2014.
View 16 Replies
My 06 Elantra started to stall / misfire when I was driving it. It doesn't seem to matter how fast I am traveling as it will " misfire" for lack of a better word. It has an automatic transmission, and the rpm's will start to bounce as the car begins to jerk when this occurs.
I don't live anywhere near a dealership, so I brought it to the garage that I take my other vehicles to, and they had a hard time diagnosing the problem due to the fact that there never was an error code coming up or check engine light. They ended up finding a bad coil and changed it out.
That was 2 months ago and I haven't had a problem with it till today when the exact same issues resurfaced. And again no check engine light comes up, just the misfiring and when stopped at intersections, subsequent stalling.
View 8 Replies
I have a 2001 jetta 2.0 engine with only 130k on it. Yesterday I replaced the battery and everything was fine but then today as I started it up to go to work I started moving and the check engine light was flashing for catalyst damage. I heard that sometimes coil packs will pop if you change the battery.
View 1 Replies
My wife has a 2003 Pontiac Grand am GT 3.4L V6. A few days ago my wife was out and tried to start the car and the service engine light came on and began to blink. (Prior to this the car was running well with no service engine light) The car was running very rough at this point so we shut the car off and I pulled the codes at witch four codes came up witch were: P0205, p0206, p0300, p0443. So I had the car towed to the shop and they said that they thought that it was the oxygen sensor but after that had been replaced they had concluded that the oxygen sensor was not the problem so they had placed the old one back in. Then they said that they restarted the car and it was running fine but then pulled it out of the shop and began to run rough again.
At this point they were thinking that there was a short so they checked the wiring from the ecm (?) back to the oxygen sensor and could not find any problems. And needless to say they started the car and it began to run fine again so they told me to come and pick it up and drive it for the weekend just to see if it was a lose connection that was possibly there. So needless to say once I picked it up the service engine light was still on but the engine sounded good so I figured I would drive the car home and maybe the light would shut off. Well upon taking off and getting a few miles down the road the engine started to idol at 2000 rmp when in park or neutral.
So I stopped and pulled the code and got P0443 again so while I had the scan tool connected I cleared the codes to see if the light would come back on with the same code or with multiple again. The service engine light stayed off. So the high idol continued for a few miles I also did try to restart the car and the problem did persist. About 5 more miles down the road the car started to overheat and the reservoir had overheated. So at this point the engine sounds good it is not running rough but is really high idol. The check engine light did not come on since I cleared the codes in that short drive but I do not want to drive it because of the overheating. I do know that the coolant level was good when we started the car.
View 1 Replies
I had the transmission filter and fluid changed at the local VW dealership had some issues with that but they straightened that out and its been fine for a while well then about 2 or 3 weeks ago i was trying to mess with an audi and hit the gas (has the 6 speed auto tranny) and the car kinda stuttered and the check engine light flashed probably 4 or 5 times then went off, it did that a few times after that then my wife was driving it and it did that stutter again and the light stayed on, the code said misfire on cylinder 2..
So I replaced the plugs today and it did fine at first but when i got to about 55-60 and went to speed up and it started to miss pretty bad then steadied out and sped up. no check engine light or anything but it was missing.
View 1 Replies
So I was driving my 2001 1.8t last night and put the pedal to the floor to make a yellow light and the check engine light began to blink and the engine started running very rough ever since. It idles very rough and it seems like I have lost a lot of the power.
View 7 Replies
My 1999 Passat 1.8T (AEB engine) with 120,000 miles has run very well lately.............except for a recent problem. I drove 150 miles on southern California freeways, parked the car for an hour, then started it again. There was a distinct miss and the check engine light began flashing. I turned it off, let it sit for a couple hours, then plugged in a code reader. There were two codes, both the same - P-0302, "Cylinder #2 misfire". I pulled the cover off the engine, wiggled the wiring to the #2 coil, cleared the codes and started it up. There was no miss, maybe there was a little corrosion on the electrical connection?? I know there was a recall on the coils, but my car was too old to participate in the recall. Which it is - bad connection, bad coil, or something else? Or a way to diagnose it further?
View 2 Replies
I recently had my PCM flashed due to the deceleration safety recall. My engine now revs to 2200 rpm when I start it even if the engine is hot. It goes down to 750 rpm after about 30 seconds. My engine before the recall, reved from 1200 to 1400 rpm when starting. My dealer and ford tell me 2200 rpm is normal but I think it is too high.
View 7 Replies
