Elantra HD (2006-10) :: When Put In Park Car Kept Rolling Like In Neutral And Started Making A Loud Grinding Noise
Jan 2, 2015
I have a 2007 Elantra with 138,000 miles. I never had any slipping or jerking or reverse issues in the past. I got into the car put it in reverse just fine then put it in drive and nothing happened, I put it in park and the car kept rolling like in neutral and started making a loud grinding noise. When I put the transmission in any other gear the noise stops but will not move and acts as if in neutral.
View 2 Replies
Advertisement
My 2009 Sonata, 2. 4 L engine, base model with automatic transmission started up and ran OK, but 20 minutes later when I parked the car and shifted towards Park the gears grinded in neutral, stopped grinding in Reverse, and then grinded again when I made it to Park, and I quickly turned off the engine.
When I restarted, it grinded in Park, OK past Reverse, Grinded in Neutral, and then OK in Drive. How serious this is, or if there is anything I can check out on my own?
View 19 Replies
I have a 2008 Hyundai Santa Fe and there is a loud grinding sound when the car is in park and neutral. This noise doesn't happen all the time but i would say 50% of the time. When there is the noise it does go away when i put the car into drive or reverse.
View 16 Replies
My Dad has a 01 f150 xtended cab 5.4 auto. Some of this info is second hand. He had driven it on a trip about 50 miles,when he started it to return he said it did not want to engage, put it in gear and nothing happened. Messed with it a bit and got it to go. was fine for about 30 miles or so. Then it started to make noise. I trailered it home and drove it a couple hundred yards to the shop. It sounds like a very large, very dry bearing, also seemed to catch/lock up then clunk.
With the wheels off the ground you can kick it into neutral and while the wheels are still rolling it quiets down. Also it does it sometimes while in neutral. When it is in park it sounds like stuff is still turning. At fist I thought wheel bearing or rear end until it made noise in neutral and park. The noise in park is not loud, just sounds like things are turning. It is full of fluid. The tranny has always worked flawlessly and still does even with the noise. Where to start looking? Transfer case?
View 1 Replies
I just had all my belts changed on my 2009 elantra. Now when I start my car it makes a loud squealing noise. it goes away after about 1 minute, we took the belt off that controls the air conditioning and still squealing.
View 2 Replies
I was driving 90 km an hr. and my trailblazer went into neutral and started making a ticking noise and it wont go forward or backward...
View 2 Replies
Getting a loud rattling noise from the front of car in Park or Neutral? As soon as I put the car in D/M. I have heard that the transmission is noisy in neutral, but just want to double check.
View 8 Replies
I have a 1994 F-150 extended cab electronically activated 4x4, with the 302 V8 and an e4od transmission.
When the truck is running and it is in park or neutral it makes a grinding/whining noise and when it is in gear it doesn't engage, or occasionally will barely engage, but only enough to move it a little ways.
I've read a couple of post that suggested bad connections to the transmission could cause the transfer case to be in neutral which could cause a similar problem to this. I checked all the connection the best I could and the only thing I found that gave me any concern was one of the wires connected to the transfer case shift motor had some of the insulation melted or rubbed of and the wire was a bit corroded.
Is there any chance that this could be causing my overall problem with the truck not driving? Or what might be going on with it? Or any way I might be able to fix it without having to hand over a significant chunk of change for the full rebuild.
View 4 Replies
Is it possible to cause damage to a vehicle (2003?? Chevy Trailblazer) with an on-the-fly 2WD to 4AWD system by switching to 4AWD when the vehicle is in park or otherwise not driving forward? This was done by someone and now the vehicle is making a loud noise.
View 2 Replies
I have a 1997 F150 (truck in signature). In December my passenger side parking brake cable broke so I replaced both rear cables (front cable appears in good condition).
This past Friday the passenger side brake started making a grinding noise so I pulled the drum to find the self adjuster cable broken and the ratchet jammed between the shoe and the drum. I pulled everything apart and put new shoes (the pin the ratchet pivots on was broken off the rear shoe)and all new adjusting hardware (adjuster screw, ratchet, cable, and cable guide). The rest of the hardware looks in good condition (still paint on the springs and retainers). I got everything put together and took it for a test drive, it had a nice firm brake pedal (it's been a while since this truck has had a firm pedal) and great stopping power.
Took it to work today, and on the way back I stopped to pickup a package from the UPS store. I set the parking brake and put the truck in 1st like I always do. When I got back out to the truck to drive home, I released the parking brake but there was still obvious drag as I drove home (no good place to stop during rush hour), got out of the truck and it reeks of burning brakes. I pulled the driver side drum off (after it cooled), which was rather difficult, and everything looks to be in order except the rear shoe was not touching the post at the top of the backing plate. I checked and the adjuster was still all the way in, so that isn't the issue.
I pulled the parking brake cable out to slack the drum side of it (with the pedal released there is some spring tension from the pedal mechanism) and clamped it with vice grips so the cable was slacked and the shoes were then touching the post, and the drum could be installed and turned relatively easily, I then removed the vice grips and let the spring pull the tension out of the cable and the brake held firmly (requiring considerable effort to turn the drum). Is there anyway to adjust the spring tension on the parking brake cable when the parking brake is released?
Additional notes: when setting the parking brake, the pedal will only go down an inch or 2 before the brakes are locked up tight and the pedal won't move, it used to go down several inches before. also I noticed that the feral on the end of the drivers side cable (that locks into the lever attached to the rear shoe) is deformed, like the cable has too much tension on it. The cables are the correct ones for my wheel base according to Autozone but I'm starting to wonder if they are too short. Spring tension on the parking brake cable (when the brake is not set) causes the parking brake to drag. How do I get the parking brake to stop dragging? ("star" adjusters are new and adjusted all the way in).
View 7 Replies
My wife has a 2010 Explorer 4.0 with 46000 miles on it. Yesterday the compressor started making a grinding noise when you turn the defrost on. It's only when the clutch kicks in. I'm hoping its something simple but, I fear its not.
View 8 Replies
We were driving last weekend in a heavy rain storm when our 2004 XC70 started making a loud siren noise. The noise increased with acceleration. We pulled off the road, turned the car off. When restarted the sound was gone, but then returned again when driving in heavy rain. Any clues as to what is causing this noise and if it needs attention?
View 21 Replies
I have a 2010 Accent GS, 5 speed. While sitting at a red light, or even rolling in neutral, the car will just die out. 90% of the time, the car will start right back up, no problem. A few times, though, it would not start right back up.. I put my flashers on, and just keep trying. It eventually starts up again, as people honk and get angry at me, but once a nice guy pulled over and offered to give me a jump and it started right up. I drove right to an autoparts store and had them test my battery, starter and alternator. All came back perfectly fine. There is no check engine light coming on when this happens. There is no code produced. A knowledgeable friend recommended i just change the battery since my car is 6yrs old, 104k miles. He said he had a similar experience and just changing out the battery solved everything. Well, i just did that and it stalled again. That obviously was not the problem.
View 8 Replies
2001 Hyundai Elantra, with an automatic transmission.
1. I am experiencing a "grinding" sound upon my initial acceleration from park? This only occurs when the car has been sitting for a decent amount of time and the engine is relatively cold. To give you more detail: I start the car, throw it in gear and begin to accelerate. The grinding sounds is almost instant and sounds horrible. It is fairly consistent how long it lasts and generally once the car shifts to 2nd or 3rd it goes away. I do not hear it again until I park, leave the car for a while, then start it up and begin driving again.
2. I am hearing a "tension" like noise, also a little like scraping, when I brake at slow speeds coming from my driver side front wheel. I recently had my brakes replaced so I know its probably not the pads and at the time the rotors looked fine too. It is not a constant noise during the breaking either meaning, I apply the breaks, i hear it for a second, then it goes again, then it comes back, then goes away. Again it sounds like a mix between scrapping metal and tension.
What it could be, what I could look at on my own or how to get it resolved?
View 3 Replies
I have a 2009 Toyota Corolla and it's making a loud grinding metallic noise on the front left side. It does it while I drive the faster I go the louder it gets. When I turn to the left it makes it louder, when I turn right the noise decreases. PG&E have been breaking the roads by where I live and there's a lot of little rocks I drive thru. I'm wondering if that's the problem?? What do I do?
View 4 Replies
No codes, transmission makes a slight grinding noise when putting it into reverse only. Has a slight bump from 1st to 2nd. I flushed 16 quarts of the sp3 through it. Been researching and see a lot of talk about the output and input sensors. Not my car but my sisters. Needs axles, timing belt water pump, ps return hose, plus have champions in there and old ass hyundai wires.... thing does idle rough, motor mounts are new.
View 1 Replies
I bought a new 2013 Hyundai Elantra Coupe this past August and this is my first car.
My first concern was that Hyundai advertises 27mpg in city and around 37(?) for highway. I acknowledge the fact that Hyundai recently had to lower their mpg estimates for some of their cars and provide reimbursements but however, these reimbursements are for 1-2mpg difference. My car after more than 6 months is still only getting about 14-15 miles on a casual drive in the city and only about 19-20mpg combined and about 24-25 on the highway! I am only getting about half the estimate for in city! I do not drive aggressively. In fact I am a pretty safe driver since I am a new driver and cautious about everything. I am also using premium gas on my car. I called the dealership I got the car from and they were trying to tell me about the reimbursement program which I already knew of... The reimbursement based of the 1-2 mileage difference is not what I want. I want to fix it and get close to the estimated mileage as I can. What is the best way to go about doing this?
The other issue is that sometimes when I hard brake, my car makes a loud grinding noise. My dealership's service center said they could take a look at this. I was mainly wondering if there is anything I should be concerned about for this?
View 54 Replies
So, last week I got my transmission replaced and they also had to replace the CV axle because it was damaged beyond repair when the Transmission self-distructed. They drove it after all the repairs and said it was driving fine, just that it had a belt squeak.
On my way home (30 min drive) about 10 minutes in, still in the city, my brakes start making a grinding noise and sort of a thump thump thump when I brake which sounds like its coming from the passenger side front, it makes me really nervous. It doesn't sound like any brake grindy noise Ive ever heard before and it wasn't making any brake noises before it broke down. (On a side note: it also made a weird noise maybe the first 3 times I drove it after getting it back and I turned the wheel hard to back out of a parking space, that used to be when I heard the belt squeak but I haven't made it squeak since I got the car back.)
Everyone I talked to said it sounded like it needed new pads so tonight I bought new brake pads and rotors for the front and got everything taken apart. The rotors didn't look bad at all, just some light surface scratches, nothing deep, no warping I could see, and the brake pads look almost brand new. I did notice that the inside brake pad on the passenger side was missing its little metal plate that is usually between the caliper and the pad, so I went ahead and replaced all of the brake pads hoping this lost metal plate was the issue.
I also turned the rotor by hand on each side while the brake pads were off and the only difference I could notice was when turning the passenger side one it made a little more noise almost like it was loose.
I got everything put back together and drove around the neighborhood with my boyfriend in the car to listen, the grinding noise was gone and it seemed to brake really well (never got above 30 mph.) However, on my way to return the rotors to advanced auto (45-50 mph) it started making the thump thump thump noise but without the grinding, still on the passenger side. I can feel it in the gas pedal and now it not only happens when I'm braking, but also any time I let my foot off the gas pedal. The only time I dont feel/hear it is when I'm accelerating.
View 3 Replies
So 2 weeks ago I noticed that after 30 minutes of driving on the highway my steering wheel started making a loud growling noise and vibrating really hard! When I hit the brakes it got worse but got better as I slowed to 30 mph. It doesn't happen all the time and not right away, only after a while of driving and the dealership says without codes they can do nothing...
View 7 Replies
Having problem with my car (2001 Elantra GT) - over the last month or so it's been occasionally making a very loud (not but consistent) grinding noise coming from the front of the car when decelerating at low speeds. The noise sounds like gears slipping over each other but cuts in and out. It's pretty loud and not a nice noise to hear! Sometimes it makes the noise when I brake firmy but not until I reach lower speeds... mostly it's just when coming to a stop, but it did it once last week when I was pulling very slowly out of a parking spot and not even braking.
As it's become more frequent (going form maybe once a week to several times every car journey) I have started to feel something in the brake pedal also, like there's something kicking it from behind. I took it to a mechanic and had to pay a ton of money to get a broken front left ABS ring replaced (it also had the front right ring replaced in May), and within 2 minutes of driving away from the place the noise was back. Before I spend even more money that I don't have on taking it back for extra diagnosis.
I'm told that this is almost certainly the ABS system that has a fault even though the ABS light never shows except when I start the car, and I've taken the fuses out of the ABS in order to confirm that it is. I haven't heard the noise after a few days of driving with ABS unplugged so I think we can be reasonably sure here. Is there anything that I can check myself or test (I'm not very handy when it comes to cars) or can you tell from this information what it's likely to be? Other things that I've noticed with the car which may or may not be relevant are:
- the warning lights for brakes, ABS and TCS are all lit with the fuses for ABS1 and ABS2 taken out. I take it this is normal for all 3 to illuminate with the fuses out?
- since unplugging the ABS I've noticed a slight metallic squeal from the brakes as if the brakes are worn down. Didn't notice this before I unplugged ABS though it may have been there, not sure.
- sometimes when going over a speed bump or just a minor imperfection in the road I hear a clunk in the front of the car and feel something move in the underside of the car. Happens mostly at lower speeds also, but not if I go over the bump really slowly.
- in the fuse box when I took out the ABS fuses I noticed there was a bit of minor melting/brown burn marks on the top of the connections marked (iirc) ECO3 and ECO4 on the diagram (large white connectors). Is this anything to be concerned about?
- sometimes when I have air coming into the car through the air vents it will become significantly warmer for a few minutes, then slowly go back to normal. Can't think of any circumstance that links the times when this happens (eg. speed, weather etc).
- the oil pan has a leak which is on the list of things to fix when the car works properly.
View 2 Replies
I have an 2002 Hyundai Auto.
My car has the clicking noise under the following situations:
1) rolling in neutral with/without brake applied
2) rolling/decelerating without gas pedal pressed (I guess the same as rolling in neutral) with/without brake applied
The noise is the most noticeable when going at around 20 to 30mph, and would be gone under very low speed <5-10 mph. The weird thing is when I press the gas pedal and the car is accelerating, the noise is gone too.
My mechanics said it is because the wheel cylinder which is noisy. But I don't quite understand why the noise is gone when the car is accelerating.
View 8 Replies
