Elantra HD (2006-10) :: How To Set Tension On Timing Belt Tensioner
Dec 27, 2013
I am deep into replacing the timing belt on my 08 Elantra 2.0, and am nervous about taking the tensioner off since it is not obvious how to set it. I could use a fool proof explanation on how to set the tensioner.
The Haynes manual talks about 1/4 deflection but that seems too imprecise.
I can not see the marks in the video : DIY 2008 Elantra timing belt video 2 of 2 - YouTube
And this post 2008 Elantra Timing Belt does not quite seem to explain. I am contemplating putting it all back together, just changing the accessory belts and handing it to a shop. I could use a fool proof explanation on how to set the tensioner.
View 7 Replies
Advertisement
Is there a "how to" on adjusting the tension of the timing belt in a 2002 accent 1.5L ....
View 1 Replies
I am working with Honda dealership management because I had my timing belt changed at 102,000 miles and 25,000 miles later The belt broke and frayed while driving in heavy traffic at night on freeway leaving me stranded in the median luckily instead of in the middle of the freeway. Honda dealership stating that the idle tension pulley caused the fraying of the belt not due to poor workmanship by their mechanics. I am asking dealership to consider assisting in payment because the day the belt went out, the car had been serviced for a oil change.
When I was called to be notified the job was complete I asked the service rep questions about the oil transmission and told him there was a noise in the engine could they check it or did they check it which she replied no that I would have to make another appointment for that. So even if I would've made appointment the next day the damage was already done because that night is when the belt broke Is this part of Hondas responsibility is it reasonable for them to take part responsibility. Also if the idol tension pulley had been changed at the same time of the belt, it would've saved my engine. So this is all my responsibility not theirs?
View 19 Replies
One of my belts squeaks. I've tightened one of them as far as it goes I think. The other one is the one with the alternator. Do I tighten the pulley bolt on the alternator to add tension to that one?
View 4 Replies
First off I have a issue the Timing Belt Tensioner Stud / bolt that holds my tensioner on is stripped and came out with my tensioner. I don't want to risk putting it back into the engine because some one prior to owning my car stripped the nut that holds it in. Where I could get a new one of these bolts. I have a 2000 VW Golf GL with a 2.0l. I've searched high and low on parts sites and cannot figure out where to buy this item.
View 3 Replies
I recently bought a 97 960. i have had a s90 before in totaled it i loved the car so much i found another. i was driving and broke the timing belt tensioner which in turn lead to the breaking of 5 exhaust valves that i know of. I've taken off the head and noticed that one of the bottom of the valves had melted onto the number 5 piston head.
I called around and search but every motor is at least 1000 and i have been told anywhere from 3500-4500 to rebuild. My question would b is there an easy way to fix or should i junk it. i bought it for a 1000 it has only 140000 on it an its in almost great condition. I attached some pictures of the head and piston so u can see the damage.
Attached File(s)
2012_04_07_19.02.39.jpg ( 1.45MB )
2012_04_10_16.45.26__1_.jpg ( 1.43MB )
View 1 Replies
I recently had a good amount of work done to my Mk4 R32. Last night on my drive home from the stealership I ended up with a passenger headlight out and a very loud clicking/ticking noise which seems to be coming from the Serpentine belt area. After closer inspection it looks like the tensioner lines are't lined up which means my belt and tensioner need to be replaced? I'm not sure, but I have a video and this picture.
View 7 Replies
Six months ago my 2005 Honda Pilot got a new timing belt that was incorrectly calibrated. When the Honda Dealer test drove the car, they damaged the values. They fixed the valve damage and gave me a discount on the timing belt. I considered selling the car, but decided to keep it.
Now it's six months later. When driving I hear a "clicking noise". The dealer says that the timing belt tensioner needs to be replaced and that it would be dangerous to drive it at high speed as it is now. The clicking is caused by a worn ??? tensioner.
They claim that the incorrectly calibrated timing belt could not have caused this problem with the tensioner.
View 5 Replies
I have a 2009 Elantra (automatic) that already has 52K miles on it. I drive a lot mostly at highway speeds. I know several people who recommend having the timing belt replaced BEFORE the warranty runs out at 60K miles.
The dealership has a 60K inspection where they "inspect" the timing belt (plus a whole lot of "fluff" checks, tire rotation etc) I'd rather just take it in and get it replaced. What should a timing belt replacement cost?
View 1 Replies
My girls family has had an 08 elantra 2.0 new since 2008 and I've been doing the work. I recently did the timing belt ( July) with beck arnley oem parts. 65000 miles. I replaced belt, idler, and tensioner.
Right after I did it there was a mild hum at idle. It somewhat did this before the belt so I assumed it was just the new belt in plus the very mild hum it already had.
Recently it is humming very loud and high Pitched. It gets louder with higher rpm. If I take the cover of and move the needle on the tensioner while it's running it quiets down a little but it's an auto tensioner and doesn't stay right where it needs to be AND even when it is at the ideal spot it still hums.
View 12 Replies
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
View 4 Replies
2008 Hyundai Elantra, 2.0 it. We replaced a bad water pump, and timing belt while we were there. I followed directions found on multiple websites. We spun the crank shaft to the top dead center mark on the crank sprocket/engine block, and the cam sprocket / assignment mark. Then removed tensioner, and belt. Installed new belt and ensured alignment marks had not moved. Applied pressure to tensioner and tightened. Reassembled everything else. Car started with no problems, drive for about twenty minutes started making clicking sound from under the hood, we turned around to come back home and the car still making clicking sounds gradually started to loose power and speed until the engine stalled and would not restart. Trying to find out what could have happened.
View 2 Replies
Changing timing chain tensioner? Mine is making the rattling noise on startup. Tried searching one internet for any DIY's out there. Haven't really found any good ones.
View 7 Replies
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies
Yesterday i went to mechanic and changed Timing chain tensioners, with chains and all guides. But still have 2 second voice on startup, once oil pressure lights off everything fine. I paid heavy price on parts and labour but very disappointed after hear same noise again today morning which i was listening from one year purchase of this car... Sonata 3.3l v6 ....
View 4 Replies
How to replace the belt tensioner. It's not putting out enough tension when the engine is cold. So, the belt makes chirping noise for couple of minutes idling when cold with AC on.
I had the AC inspected and everything checks out according to my mechanic.
He believes that the issue is with the tensioner since I had recently had replaced the serpentine belt.
View 6 Replies
Changed the timing belt. Used the red mark up top and the cut in the block on the lower one to get TDC. Changed everything with new parts. Double checked the marks after the belts were on (rotated by hand through two full turns and checked to see if the marks were in the same spot). I followed the write up that was posted here by U95.
Anyway, the car won't start. It tries cranking, but won't actually start. There is fuel and the battery should be good to go. There shouldn't be any Fuel/Compression/Air issues.
I guess my question is: If the timing belt is not tightened enough, would that keep it from firing?
Also, in trying to crank it by key every thing sounds normal (no knocks or pings or valves getting bent sounds) and turning by hand gives just the little bit or normal resistance but spins nicely.
I'll probably take the battery to get it load (I used my tender to try and start it as well, didn't make a difference) tested tomorrow and then try the starter (shouldn't be bad though, only 60k on the car). Otherwise I'll have to teardown and start over.
View 13 Replies
To my knowledge, if the timing belt goes the engine shuts down. According to others on Hyundai forums, you can blow the engine in a Hyundai Elantra if the timing belt goes. Is the latter really the case?
View 9 Replies
I recently replaced the timing belt, tensioner, and roller in my car. Today I became concerned that I hadn't tightened the tensioner properly so I did a quick check (it was). I also noticed the timing belt felt a bit loose, so I tightened it to what I thought was about 1/4" deflection with 5lbs pressure—not what that feels like in that tight space.
When I started the car there was a noticeable whining sound. Before I changed the belt there was a slight whining sound (but there was no whine after I changed the belt). So I loosened the belt a bit and there's now a slight whine. I feel like the whine shouldn't be there but it's hard for me to imagine that the belt should be any looser since I can move it 1/4" inch without much effort.
So, should I be tightening the belt to the point where the whining is gone, or is a slight whine ok?
View 2 Replies
I just changed the timing belt on my sisters car and finished yesterday and drove it today. A check engine light came on so I went to check it out and P0016 popped up. I've done some research and people say that it might be that the timing belt is misaligned or loose. I tightened the belt not too tight but not too loose. Note: I also spilled coolant on the crankshaft pulley and a bit on the belt itself. The car idles rough when driving too. I will tomorrow take off the cover and check the tension of the belt.
View 9 Replies
I just put in a new water pump and timing belt on an 06 Camry with the 3.3L V6. After I was done the TCS light turned on and I don't know why. The light was never on before and the car is running very smooth.
View 2 Replies
