Elantra HD (2006-10) :: 2009 Engine Rough Idle After A Run
Jul 16, 2013
Have a 2009 Elantra 4 door, manual. It is at 52000 kilometers and recently in the spring changed the oil, I run Full synthetic.
Lately its been really hot and the following problem occurs, no engine light or anything. But if I start the car cold it idles no problem, nice an smooth, If I go out for a 30min drive, come back and let it idle its rough. Not crazy rough but its rougher than it should be. I have no power issues, it pulls well, never stalls. If I shut it down and wait a few hours, engine still hot, but not super hot, start her up and runs well, no rough idle.
Go out for a 15-20 min drive and park it, idles rough. I checked the usual, wires, plugs, pvc valve seems good. Engine temp is normal also. I did some searches on the site but come up mostly with cold idle issues, not great when cold not so when hot.
View 9 Replies
Advertisement
A few weeks ago I noticed a fluctuation in my car's heater. The heater blows really hot when driving, and blows cold when the car is idling or coasting. I read up on the forums to check the coolant levels, which were full since my last fluid change a few months ago. The next step seemed to be to change the thermostat. I changed the thermostat and the heater acts the same, and since then the car has begun intermittently overheating. The temperature warning will flash on for maybe about a minute, then go back off. I have been running the heater on full blast trying to keep the car from overheating.
This brings me to a couple of questions:
There's an arrow on the thermostat. Does this need to point toward the radiator, or straight up?
In moving the air cleaner housing to get to the thermostat, I lost two of the little clips that hold it shut. Is this critical?
If the thermostat is good, and the coolant levels are good, there's no air in the system and I don't have any leaks, what could this be?
View 16 Replies
I own a 2010 elantra. I'm going through plugs like crazy. I've changed it twice and the dealer has changed them twice for a total of 4 sets. I have 64000 Kms on my car. The problem is rough idle when ac is on. I'm assuming drag or load on the engine makes plugs work harder.. So the last two sets of plugs the dealer showed me the plug and the white spark plug casing was burned through? Kinda getting sick of the bandage approach the dealer is throwing at me. He said if it happens again which I'm sure it will they will sort it out in more detail to find the cause.
View 4 Replies
My moms has a 2010 Elantra with 30,000kms on the clock, and we have noticed since new when the vehicle is started cold in the morning it seems to run rough for about 30-60 seconds then stabilizes.
It's almost like it has a slight misfire, or slight fuel flooded from sitting overnight. Now if course we have taken it to the dealership twice for this issue and dropped it off overnight for a cold start, and both times they cannot re-produce the problem.......surprise.
View 6 Replies
I have a 2009 Accent and after about 20 minutes of driving it started running really rough and my check engine light came on. It's worse at an idle (feels like it's going to stall out) but isn't quite as bad when I rev it. My first thought is water in the gas tank since we've had a lot of rain for the past week or so and I filled it up a day or two ago.
View 2 Replies
I have 114,00 miles on my car. Plugs changed and decarbonization done at 99,000 as well as ECM reprogram or update ($99). Anyway, when my car sits overnight and starts it is getting a rough high idle until I feather the pedal or give it a minute or 2 and it is fine. It is warm now in the 70's and this just started. I had it to the dealer for oil change and they looked at it. There are no codes, they recommended changing the plugs and doing a decarb again. So I told them if I need plugs there is something wrong, Iridium OEM were installed.
Anyway, they suggested changing the throttle body since it has new sensors. I have have the TPS replaced before when engine was surging. They told me there are 2 sensors and one could be bad in throttle body. I don't get it, I use Hyundai air filter now and change every 15,000 miles and get oil changes regularly and they use Quaker State Synthetic blend. I am wondering if maybe I have a faulty PCV? I don't think that has been changed. Don't even know what the interval is. Previously I was told there was none, but I disagree.
What would cause me to get carbon build up like they keep telling me? I don't want trial and error and throw parts and money at it since there are no codes. I was going to drive it til it throws a code. I do highway driving in suburban area, mostly 65 mph. The car runs good, still the intermittent hard downshift when slowing down but nothing like before the tranny was replaced.
View 2 Replies
When sitting in Neutral or Park with the engine warm, my throttle goes from idle 650-700 right to about 2000 RPM. I have 14,000kms on it now. The fast idle works OK at RPMS between that OK when the engine is cold so it doesn't look like a ECU Problem.
There is no way that the RPM can be set lower, when attempting to go lower it drops right to idle. The dealer says the TPS is testing OK, but it never did this when new. It used to go gradually right up the scale.
What the dealer TPS testing actually measures? I suspect that it only measures the output voltage to be within requirements of 5 to .2vdc, but doesn't have anyway to measure a linear change in voltage that should be taking place when the throttle is depressed. And since the engine never tries to speed up unexpectedly except under no load conditions like this, they say it is normal and won't change the TPS.
My guess is that the TPS resistor is not working linearly and that the first part of the throttle movement doesn't change the output voltage to allow throttle setting for a lower RPM than 2000 under a no load condition only.
Remember you can only test this in park or neutral with no load and the engine warm.
Further investigation has shown that the TPS output is linear and the ECU just doesn't react to changes in voltage that will allow the engine to run at less than approx. 2000RPM under a no load condition. Apparently all the 2.0 litre engines perform the same way by design.
It would seem to indicate that safely controlling your vehicle with precise fuel adjustment in tight places is not necessary by someones standards.
View 9 Replies
I just purchased my first foreign car ever. it is a 2002 Elantra it idles very rough changed plugs using NGK and wires new fuel filter and ran 2 full tanks of high grade fuel with STP fuel injector cleaner. but had no effect on idle also have no check or service engine light. What to check next?
View 3 Replies
Check engine light had come on, the car was running rough at idle and it would crank hard. So I threw my code scanner on it only to find out it wouldn't link. Drove it to O'Riley's and had them pull the codes. It ran rough and had next to no power on the way there. O'Riley's pulled the codes and we got a P0300 (random multiple misfire), P0301 (cylinder 1 misfire), P0302 (cylinder 2 misfire), and a P0496 (EVAP emissions system high purge flow). So once I got it back to the house, she told me that she had the codes pulled once before and that they told her it could be her gas cap so she replaced it. She also stated that she had replaced the plugs about 3 months ago.
So with new gas cap and new plugs, and these codes, I did a bit of research and come to the conclusion that it'd replace the purge solenoid. The solenoid was making a pretty loud ticking noise and when I pulled it off, it rattled so I figured that was the fix. Pulled her plugs and you can clearly see that cylinder 1 was running VERY lean and cylinder 2 was a little richer but still too lean. Plugged the plugs back into coils and laid them on exhausted. Turned the car over and we had spark. Lead me to think the misfire had something to do with the P0496 EVAP code. Put everything back together and erased the codes. Gave the car back to her and told her to let me know if the light came back on. That was Wednesday last week. Sunday she told me the light came back on and the only code that came up was the P0496 again. When I gave it back to heron Wednesday, it would still crank hard but would start.
Battery is new and checked good, alternator is pulling about 14v and checked good and the starter checked good. My dilemma is the code and the hard crank. She told me that it only cranked hard for her once so I am assuming that has gone away but we're still left with the P0496. I am not 100% sure as to how this system operates but I understand it for the most part. She told me that she had just put gas in it before the light came on. Not sure how much time had elapsed after filling it and the light coming on but I do know she put gas in it. If it's a high purge flow, that makes me think there may be a leak in the system but I'm not sure where to go from here without throwing a bunch of parts and money at it.
View 14 Replies
I have a 2006 azera limited with about 63k miles on it and I noticed in the owners manual that at 60k I should have the valve clearance checked and adjusted if theres vibration or rough idle. I currently have a rough idle and more vibration from the engine.
View 1 Replies
I have a 2006 azera limited 63k miles on it and I'm getting a rough idle that sounds worse when the weather is cold. also when I press the gas there is hesitation from the car to accelerate. on top of that, I feel vibrations from the engine all through the driver and passenger seat. When I turn the car on it idles at 1300-1500 rpm and takes about 5-7 minutes to come down. when it does , it idles at 650 rpm. I'm not getting any check engine lights or codes. I've replaced spark plugs, air filter, had the air induction service done at the dealership, and had to have Hyundai put on a new throttle body last march when it gave out on me while at work. the dealership doesn't know what it is and said to use a fuel additive when I fill up the tank. I have and am waiting to see if that does anything. I put in a bottle of CRC 1 Tank fuel system cleaner 2 days ago. I've even changed my brand of gas from exxon to bp just in case. I think it may be a bad hose for the idle and a bad motor mount for the vibration. Could an O2 sensor be going bad?
View 1 Replies
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
View 5 Replies
I have Subaru B9 Tribeca 2006. Week ago started the following problems - after starting up, engine is shaking (rough idle) for a few (20-30) seconds and then it's OK. Then I got Check Engine, Cruise and ABS lights on. Diagnose shows mistake in 1st cylinder. changed spark plug, air filter, checked all connections, cleaned injector and throttle. Lights went out and engine was working as new. but the second day car had rough idle again....
View 1 Replies
My check engine light popped up the other day and when ran, 3 codes popped up: p2414, p2195, and p0170. From what I could gather it looks to be the O2 sensor is bad. This would be the one on the exhaust manifold, correct?
Also, what would cause the o2 sensor to go bad in the first place? My 09' has roughly 65k miles.
View 13 Replies
I just bought this car from the original owner. She didn't take that great of care of the car. First oil change was done at 8,000 miles for example. Basically if it was broken she would fix it, but didn't do much preventative maintenance.
I just replaced all 4 spark plugs and coils since one was misfiring and didn't want to have to go back in and replace one in another few months. Replaced the AC belt a few days ago since it was cracked and worn. All other belts are fine. I drove the car around for a few hours the next day and it ran great.
Today, the check engine light flashes and then stays on. The car is idling rough at stop lights and acceleration is poor. Previously, the light came on and it was the EVAP system. Not sure which component and I was told it isn't supposed to affect the way the car drives.
View 14 Replies
I have a 2006 Hyundai Sonata with a 2.4 liter 4-cylinder engine. After filling the gas tank, the car idles roughly, but accelerates and performs fine at higher speeds. The rough idle lasts about 5-10 miles and then goes away.
Six days ago, I changed the spark plugs and air filter. Four days ago, I filled up with gas (and had the same issue with the rough idle). This morning, I started the car and idled it for 2 minutes while I scraped ice off the windows. I drove the car about 5 minutes and the check engine light came on. I took it to Autozone and the code given was P2187, System too lean at idle bank #1. "
Autozone suggested that it could be an air intake fault (MAF sensor), fuel pressure, or vacuum leak. They also said they have a MAF sensor cleaner to try. I am not sure if the rough idle after fill-up and check engine are related. Also, I don't know if the spark plugs or air filter could be related to the check engine. I was planning on making some easier checks first such as hoses near where I worked last weekend, especially near the air filter. Cleaning the MAF sensor is easy too. I was also going to check for vacuum leaks (incl. intake manifold) and recheck the spark plugs.
View 4 Replies
I started my Accent this a.m. The Check Engine Light is on and it runs really rough. I left it here at my apartment - it's that bad. It's got 27k miles.
The only other thing to note is that it's been very cold (for Northern California anyway) - around 45 degrees F right now.
First-time poster, haven't had any problems with the accent except for a sun visor that was replaced under warranty last week. All scheduled services done at the Hyundai dealer.
View 20 Replies
I have been experiencing some issues with my '06 rio5 (same engine as your hyundais). this forum is way more active than the kia forums, so figured id give it a shot here.
I am experiencing a rough idle at start up while the car is low on fuel (<1/4 tank). it idles rough for a few seconds, the check engine light flashes a bit, and then it runs fine.
The car is an '06 rio5 with approx 19k miles on it, five speed manual. Also, sometimes after refueling and it will just shut off while waiting at an intersection. Not sure whether these two issues are related, but thought i would mention it just in case they were.
View 14 Replies
Yesterday my car had a rough start (lasted all of 5 seconds) and it threw the check engine light on. Now other symptoms. It was a rough start, almost like a misfire then it idle fined, and drove my 60 mi commute home without issue. I had fine acceleration, gas mileage idle etc.
I got home and turned it off for 10 min and it then started normally and ran fine again. I'm thinking it was just a random miss that threw on the light, but I'll take it to Advance to get the code later today.
I replaced the plugs about a year ago with cheap-o plugs so it may be time for a replacement again. I thought maybe an o2 sensor but there wasn't a drop in mpg, at least anything noticeable.
And its been a few days since I've gotten gas so I'm doubting just a gas cap issue... The CEL did NOT flash, only solid the whole time.
View 8 Replies
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 Replies
I have 2005 elantra ve and I got rough idle stop for a while.
View 12 Replies
