I just purchased a 2013 Elantra GT, 3 days ago. I was driving down the highway and my check engine light came on. There is only 480 miles on my car! I know it's not a gas cap. I haven't even put gas in it since I drove it off the lot. Is there a way to check for the code thrown without a scanner? I use to have a jeep liberty and I could click the key over 3 times an the code would pop up.
View 24 RepliesMy truck is a 1997 nissan pickup with. 254,000 miles. Check engine light come on. Only when I am at highway speed. As long as I am in city traffic, nothing I have a code scanner code (PO302) number 2 cylinder misfiring. I change spark plugs and wires and dist cap. But check engine light came back on. I put in shop they claim that they can't find nothing wrong. I guess I need to find a new mechanic.
View 3 RepliesI drive a 2002 Chrysler Sebring convertible with about 130,000 miles on it.
I was driving down the highway in early November when the check engine light came on my car. I took it to Aamco who did some diagnosis and replaced a solenoid assembly in the transmission. The light went off and I was on my way. I never got the exact code.
About a month after that, the light came on again. This time, I got a low end code reader and scanned it myself. I got a "P0700" code, which I've read is a generic code that the transmission system sends to the computer or something. So I used my reader to erase it. However, the light came on 2 days later while I was driving down the highway at about 70 MPH.
So I went to an auto parts store to get a more detailed scan with a better tool. This one came up "P0740 Torque Converter Clutch Solenoid Circuit".
This feels weird, because the solenoid assembly was just replaced a month ago (and is still under warranty).
The car seems to drive okay. I don't notice any actual problems in shifting. The tachometer seemed to get up to about 3000 RPM on the highway. But I've seen practically new cars do that. The last time I had serious transmission problem it would rev up to about 5000 or 6000 RPM on the highway and still only getting up to about 40 MPH. That was 3 years ago and at the time I had a fairly expensive transmission repair (which included a new torque converter).
But like I said, the car seems to be driving okay. I don't drive much. Maybe 100 miles a week? And even that is mostly optional in town driving. I'm not looking to keep this car for more than another 20,000 to 25,000 miles though for the time being I cannot afford a new one.
What are the possible causes here? What are the consequences of ignoring this? Like I said, it's still driving fine and as the old saying goes "if it's not broke, don't fix it".
2004 Golf, manual transmission. The yellow check engine light comes on when it's driven on the highway for more than 10 miles or so (60-70 mph).
The light goes off on it's own after about 36 hours of suburb driving - 1-2 miles at a time on suburb roads, lots of lights and not going over 40 mph.
1) Why the light is coming on? No other signs of trouble occur - oil looks good, temp stays fine, no smells, etc.
2) Why the light goes off after 4-6 miles/36hours?
I have a 2013 Elantra GLS with almost 200k on it. I am the original owner. I have only had a few small problems with it just replacing lights and had to replace the passengers side wheel bearing twice. the rest has just m=been replacing wear and tear parts. the check engine light is on because it needs 02 sensors. They are back ordered. The car started idling roughly and driving horribly on the way from Rhode Island to New York on Christmas day. A friend had a diagnostic machine and the code read misfire cylinder 3 p0303..I am assuming it damaged the catalytic converter and that I now need both the sensors and the convertor. I live about 7 miles from my garage. should I tow it ? or drive a t a low speed? Have to bring it in first thing in the morning. What else could be wrong?
View 3 RepliesSo as my first post was about all the upgrades/mods I wanted to get recommendations on, it saddens me that my second is about my check engine light.
I've noticed for the past week a little bit more of a "bump" when accelerating into gear. This Friday, coming home from work the check engine light came on. Checked the oil and gas cap, everything seems ok. I'm taking it into the dealership tomorrow and will update with their findings.
I'm worried cause I would never imagine the light to come on so soon. The car is barely two months old!
While I am driving the car it will start to die and skip. Happens randomly. Today I was driving up a small hill and it went quits on me started lurching with check engine light coming on and off. The car will turn over and start, but only for a few seconds before dying again.
Seems to happen when the car is running for a while. Also the ABS light flashes on then off randomly while driving sometimes although It hasn't been an issue. Will be checking tomorrow to see if it starts.
I own an 04 Hyundai Elantra with around 196,000 miles on it, and have run across a problem I haven't had to deal with before. A few days ago, my check engine light came on while driving. I didn't really notice much, but when I started it again it began idling roughly. I got it home and pulled the code, which was P0341 (camshaft position sensor). This isn't the first sensor I've had go on the car (I replaced an oxygen sensor and throttle position sensor a couple years ago), however I ran into two problems:
1. How likely is it that it's the sensor that's bad as opposed to something like the timing belt or VVT adjustment?
2. Since the sensor isn't horribly expensive, I decided to try replacing it, but I can't get any socket to fit on the bolt that secures it. I've heard it's a 10mm, but nothing seems to fit snugly. Maybe there's just so much crud and corrosion that it's ruined the head. I tried using an extraction socket, but no luck.
I was driving slowly with cruise control on when the check engine light came on, a few restarts and it still didn't go away. All fluid levels are OK, no other errors show up on start-up or driving and the car drives fine on both ICE and EV modes.
I'm bringing the car in first thing tomorrow. I called my usual Lexus guy and he didn't know what the problem could be either. I'm a bit freaked out, to be honest. Wish I had an OBD dongle to use with Carista.
The wife and I own a 2003 Hyundai Elantra with 163k miles.
We just had our oil changed and we are currently running 5/30 and the oil light came on about a week after the change. I stopped the car immediately and checked the oil level and it was fine and oil was super clean. So I jumped back in the car and the light was off. Drove down the road about 2-3 miles and the light came back on and stayed on. Today it stayed off for a good 5-10 min while driving at highway speeds of 55-60 and then it popped on. The car runs great and it's not running hot that I know of and doesn't sputter or anything.
I was wondering if it was a bad Oil Pressure Switch? Where are they located at in the motor? I just put 1k into it with new new belts, valve cover gasket, spark plugs, wires and tires.
Check tire pressure light appeared today while driving on the highway today. checked all pressure but they all read fine. what could be wrong? Is there something I am not getting here ?
View 3 RepliesI have an 04 Elantra GT and have been noticing a jerkiness when driving at a constant speed on the highway. I haven't noticed it around town or while accelerating. I also have noticed that when I disengage the clutch on the highway, the engine sometimes doesn't respond right away, or it even may surge. This has happened when exiting the highway when I disengage the clutch. The engine will slow, then speed up close to 3000 rpms.
I also had a check engine light come on and couple months ago. The code indicated that the upstream O2 sensor was bad. I took it out and cleaned it, but didn't replace it. Is this a likely culprit for this set of symptoms? If so, how can I test the sensor to be sure? I heard that I could disconnect it and run the car and see if the surging lessens, but wasn't sure if that was a good thing to do.
I have Acura 1996 3.2 and its a great car but about 2 months ago the Check engine light is on and when i try to accelerate on highway or just on high speed it wont go in the next gear at the moment but when I am gonna press the pedal harder suddenly it will accelerate in a second. Also when I am standing on the traffic light the dashboard starts shaking and its a feeling like a car is going to turn off. Its an automatic. And this happens more frequently when the tank is full.
View 8 Replies2013 Elantra with 62k miles. I am dealing with a strange issue where I experience sudden engine shutoff and no-crank no-start situation when I attempt to restart. This typically happens during warmer weather (above 95F / 35C).
When the engine shuts off while i'm driving, the following symptoms occur:
-Temperature gauge (all bars) disappear
-Shift level selection disappears from dash
-stability control light is illuminated
During that state, I'm unable to restart the engine (even when the level is in park or neutral). Anytime the attempt to restart, the following symptoms occur:
-all of the above symptoms when engine shuts off
-TPMS light is flashing
-engine does not crank when attempting to restart.
-Unable to move shift lever from Park when key is in ON position, even when depressing the brake pedal (have to use shift lock release to get it out of park into neutral). Trying to start the car in neutral makes no difference.
The car stays in that strange state anywhere from 5 minutes to several hours. After that, I'm able to start the car and drive it for 10-60 minutes, until above issue repeats.
The issue is NOT any of the following:
-Battery
-Starter
I know that some users have reported a similar issue due to a bad inhibitor switch, but with that issue, only the gear selection disappears from the dash (while the temp gauge and other functions remain normal). Could it possibly be a bad ECU?
2013 Elantra (40k miles) just started having intermittent high engine rev while driving at low speeds (30-40 MPH). The rev last 1-3 seconds no engine codes showing up. The transmission does not feel like it is slipping.....
View 1 RepliesRecently the check engine light has started coming on every time I drive on the highway. At approximately the 5th mile of my ride, the light comes on but I cannot detect any symptoms, the car runs great. This rarely if ever happens when driving in the city, only on the interstate. My car is too old to be hooked up to the fancy diagnostic machine. What I should check to resolve this problem? 1995 Honda Odyssey with 279,000+.....
View 11 RepliesI am considering buying a used 2013 Audi Q5 with 25K miles. The day I was supposed to see the SUV the check engine light came on-. The catalytic converter had to be replaced. The dealership could not give a good reason why this happened. During the winter, the owner backed into a pile of snow--and dented the under panel in the rear that has since been replaced.
View 19 RepliesI'm due to leave at 6am sharp on Friday morning for that pre-planned surprise 50th Bday celebration I've been talking about for my wife. This evening I get in the Elantra to pick her up and when I started the car it began to shake VIOLENTLY, like I was in a commercial dough mixer. WTF!?? I saw the check engine light was on so I shut it off immediately. Curiously, I had the car out earlier without incident.
I restarted the car and it ran smoothly this time, but the check engine light remained. Calling the dealer, I was able to get a 9am appointment for tomorrow morning. I don't have an OBD-II scan tool to check the codes, but based on the symptoms, and recent poor gas mileage.
So the check engine light on my '12 with 5K miles came on 2 days ago. Called to make an appointment at the dealer for tomorrow...and today it goes off. Is it relatively safe to fore go the appointment and see what happens? I don't think it was related to the gas cap.
View 2 RepliesI just bought a used 2011 Elantra GLS and am having some issues that the dealer cant resolve. What is happening is the the Check Engine light comes on and off. It will be on for a day or so, then go off for a day or so, so I am thinking its the gas cap. So I tighten that thing up as good as I can and pulled the negative battery terminal and problem solved. About 2 days later, and about 200 miles later on the same tank of gas, the light pops back on. So I call the dealer and took it there the next day.
On my way to the dealer, the light goes out. They try and pull the code, but the ECU is showing nothing. I asked if the ECU stores codes and I was told that when the light goes out on its own it clears the ECU of the code. Not sure if that is true, but that is what I was told. So I drive the car home. I fill the car with gas, drive about 100 miles and the light comes on. I call the dealer the same day, take it over, and on the way like the car knows it goes off and guess what? Dealer cant do nothing.
Now to make a long story longer, this is what I know. The car is not a CA car. It was sold in GA and was a prior rental. It ended up in CA and was sold as a certified pre owned from a Hyundai Dealer, I actually bought the car from a Mitsubishi Dealer and they dealer traded for this car (thats another long story) the carfax does show that it failed emissions but passed after several attempts. Which I thought was odd on a ULEV vehicle. Since I liked the car so much and the price was good, I bought it since it did pass smog eventually.
Once I get the car home, I do my usual thorough look. I clean everything to my standards. I am cleaning the engine compartment and took the engine cover off. 1st thing I noticed was the Spark Plug Coil Packs all the 10mm bolts that hold them in were loose and 2 of them were completely off!! So I decided thats odd, so I pulled the plugs out and they were the NGK's so just in case I put a brand new set of the NGK laser Iridiums back in and tighten everything up. Then I notice where the PCV valve is on the valve cover, the hose that goes to that to the intake tube does not look stock. The hose looks like fuel line hose that someone put on it and the clamps are not stock. So I am canvasing for OEM replacements of those parts now. Then when I was installing the mud guards, on the drivers side rear tire where the gas filler tube is I notice another non OEM clamp. So someone was messing with this area of the car too.
The car is averaging 26-28mpg's in the city and I have been getting 35-37mpg's highway so I don't think there is anything major wrong here. I believe that either the PCV valve hose is kinked and may be causing a fault, or that since it was a prior rental that people were over filling the gas tank and maybe blew the expansion valve in the gas tank, causing the fault. I have no way to prove this since the light goes on and off and clears the ECU every time I take it in.
I have 2013 Hyundai Elantra GL which is not even 2 years old. a month ago I took my car for auto detailing to a cheap place to save some money. I noticed that after the auto detailing some of the buttons would not work on the steering wheel and the radio would turn on and off by itself. I also could not turn on the front seat heating ( which resolved by itself).
I also had to change the rear routers and front break pads due to pass out of province inspection in Edmonton. Yesterday the ESC started blinking and the car would not pick up any speed above 60 km/hr. This issue was resolved in the morning by turning the ESC off.
I took my family and took the highway and the issue started again, I turned the ESC again as soon as I pushed the breaks a bit , the system JAMMED my breaks ( THIS WAS SO SCARY) considering I was at 100 km/hr and my wife and 3 kids were with me.
I called the dealer and dropping the car off but I thought people should know of this issue , the car steered right and left and handling it was so hard. My family is so scared to even sit in this car anymore.