Durango :: 2004 - Idle Intermittently / Car Would Die When Slow Down To A Stop?
Jun 2, 2012
I have a 2004 Durango 5.7 liter hemi that is having (has always had) intermittent idle problems. My parents were the original owners, and from the beginning, the car would die when you slow down to a stop. This doesn't happen every time you slow down, but probably 1-3 times per day. It doesn't seem to be temperature related, as it happens all year and when the car is warm or cold. My parents had it into the dealership numerous times and they couldn't figure it out. My husband has changed plugs and wires, used a variety of injector cleaners and there is no engine light and no fault codes. This is so frustrating! I might drive around all day with no problem than slow down/stop at a light to have it die.
View 2 Replies
Advertisement
My 2012 Camry 2.4L is sometimes dangerously slow when accelerating from a stop. Totally intermittent. I can put my foot in the gas pedal and the car takes its sweet time getting up to speed. Almost like trying to start in 2nd gear in a standard transmission vehicle. I've had the torque converter software patch.
To be honest with you, this is a huge safety issue. Not sure I can trust my car to accelerate. My car has 44k miles and I've done all the scheduled maintenance and run only top tier fuel.
View 14 Replies
I got a 2002 sierra 1500 with a 5.3l. I just replaced both catalytic converters and y pipe. After I did this, I am having a few problems. First, when slow down to park or at a stop sign the idle drops way down and it dies. I cleaned the throttle body, maf sensor, and ran a can of seafoam and a can of b12 chemtool through it. It did this for a couple of days and now when the idle slows down the "check oil pressure" light comes on before it dies. Then yesterday the "check oil level" light started coming on. Is this all related, would the low idle cause low oil pressure, where to start?
View 1 Replies
2008 Dodge Avenger SXT Sedan GEMA 2.4L DOHC I4 / 4 speed automatic75,000 miles Moderately well taken care of (oil change every 3,000 miles, mostly follows recommended maintenance in owner's manual)
Symptoms:
*Car runs and drives fine while the car is in constant motion and decelerating.
*Rough and Slow Idle at a stop on the brakes with car in Drive. Engine speed will drop below ~400 RPM, then "kick" up to ~1,200 RPM, settle back to 'normal' idle ~800 RPM, repeat. I have suggested she put the car in Neutral at a stop to see if that changes anything, but I don't have feedback from her yet. One instance of seeing a puff of smoke from under the hood while the car was doing the above.
*When pulling away from a stop, the car will hesitate; that is the accelerator will be pressed but the throttle response will be delayed.
*When pulling away from a stop acceleration will be inconsistent; instead of rrrrrRRRRRRRRRR, it's more like rrrrRRRRrrrrrRRRRrrrrrRRRRR
*Couple instances where the car just shut off while she was parallel parking (low engine speed).
*One instance where the car did not start on first attempt. Started fine on second attempt.
*No Check Engine Light. The codes have been run.
Shop Visits (at an independent garage recommended by her roommate who's been going there for 5+ years, good reviews on yelp, and always busy):
*First visit: told her they put in a bottle of fuel system cleaner and to use a tank of high octane gas. That didn't really work.
*Second visit: cleaned the throttle body. That was 3 days ago, so far no conclusion either way.
Other repairs:
*The battery was checked (at O'Reilly) and replaced after the starting incident mentioned above. (5 year old car, seems about right).
*2 nights ago I told her to put in a bottle of HEET to get water out of the fuel system (California uses ethanol blend) and a bottle of Gumout Fuel System Cleaner and to fill up with premium gas (based on items below). Be sure to run that tank down to almost empty.
Things I could think of:
*Crankshaft/camshaft position sensor failing.
*Alternator failing (because this problem doesn't seem to exist at higher RPM's)
Research online: It seems that a number of people have similar problems with Chrysler products with this and the previous generation 2.4L engine but no clear conclusive repair. Some of the items mentioned:
*Idle Air Control (IAC)
*Exhaust Gas Recirculation (EGR) valve
*New sparks plugs and wires. (not replaced but should be)
*New timing belt. Timing belt is one tooth off.
*Water in the Fuel System (hence, HEET)
*Dirty/Clogged Fuel System Component (hence, fuel system cleaner)
*Failing Fuel Pump
*Dirty/Clogged Air Filter (replaced per maintenance manual)
*Low Oil Pressure/Failing Oil Pump
*Additionally, there are no recalls against her VIN.
View 1 Replies
Over the past few months, my 1999 Dodge Durango with 64,000 miles on it and the 5.9 liter engine inexplainably dies when driving. It has happened about 4 times over the past 6 months. I will be driving along and all of the sudden, the car turns off while moving. I have to pull off the road and sit for a few minutes. After a bit, I start the car back up and it runs fine. This has occured when decelerating exiting the freeway, on a residential street while costing along and while accelerating on the freeway.
View 13 Replies
Early this morning, after a night of freezing rain, i noticed the rear wipers running even though the car/ignition/wiper switch were all off. truck had not been started in over 24 hours. was unable to stop motor from running except only by disconnecting battery lead terminal. on trip to local mechanic hours later, motor would not stop, except when I turned-on front wipers -- then the rear motor would immediately stop at whatever position wiper blade was in. motor would not park blade. only tripping the front (separate) wiper switch would interrupt power to rear wiper motor. At mechanic, problem would not reappear. learned later that similarly, the front wipers would not quit two weeks earlier. at that time, the front wipers eventually stopped some time after ignition was killed and vehicle sat idle with all switches off. Common thread is problem appears during rain storms and does not manifest during dry times.
View 3 Replies
Over the past few months, my 1999 Dodge Durango with 64,000 miles on it and the 5.9 liter engine inexplainably dies when driving. It has happened about 4 times over the past 6 months. I will be driving along and all of the sudden, the car turns off while moving. I have to pull off the road and sit for a few minutes. After a bit, I start the car back up and it runs fine. This has occurred when decelerating exiting the freeway, on a residential street while costing along and while accelerating on the freeway.
View 19 Replies
I have a 2005 Dodge Durango, 4.7 V-8, 76,000 miles. When I come to a stop I smell oil that comes thru the air vents. It goes away when I go down the road. I have heard this discussed before on the show but cannot remember what it was.
View 3 Replies
My wife's car is a 2006 2.0T Passat. It has been very slow to blow cool air on starting. Once you are moving at highway speeds it cools fine, but then blows hot air when you slow or come to a stop.
I have taken the car to a mechanic who purged and refilled the coolant. This did not fix the problem. Upon checking with the mechanic, we noticed that both the primary and aux. cooling fans start and stop at the same time, and only would come on when I would rev the engine up some (around 2000 rpm).
I have talked with this mechanic and one more. Both are certified master mechanics, but neither specializes in VW. They believe it may be the high pressure side switch or the compressor itself.
View 4 Replies
The prius stock battery is weak compared to my wifes Mercury Mariner battery. The Mariner acceleration on battery alone is excellent - she can get up to 30 mph in no time on just the battery. In my prius it has very slow acceleration at a dead stop while running only on battery. Is it possible to buy aftermarket (stronger) batteries for the prius so I can at least driver the car up to 30 mph only on battery?
View 4 Replies
Looking at a truck at a dealership. 04 F150 Lariat 5.4 3v? 2wd SuperCrew 148k miles. Bone stock besides the bedliner.
Truck is pretty nice besides these 4 things. Kind of a shudder when taking off from a stop or a very slow speed. Adjustable pedals don't work.
New brakes, but possibly the rears are dragging a bit. Was able to turn them in neutral and the rear on jacks. Extra, guessing because of the newer looking battery, some systems lack data from the OBD2
I'm mainly concerned about the shudder from a complete stop/1-2mph. At the dealer, to leave the lot, the driveway was elevated. I think it showed very well climbing that hill. As it was noticed and played with the gas a bit. Otherwise, you stomp the gas, it may shudder for a second or two, (3-5 times?) once it hits about 3000 rpm in 1st, its fine. Only ever seemed to do it in 1st and never any other gear, never on any gear changes.
We lifted the rear end up on a jack and fiddled around. Put it in neutral and spun the wheels, tried to mess with the drive shaft... According to dad, who was looking at it with me said it was fine and that it's normal to have a little bit of slop, but I didn't notice any real slop myself, tried to push on the driveshaft on the transmission side and I think it may have moved a bit but it didn't feel loose or clang or anything. Although I didn't get to push on it too hard because he was rotating the driveshaft at the time.
I assume new fluids in engine and trans. My dad said something about old oil marks on the transmission pan area or something. Both to the fill line.
One thing that I wonder about is how long this truck has been sitting. I wonder about the differential clutches. I'm not that sure what it really has for the rear end. But google had mention of clutch packs in the rear. I wonder if because it's been sitting that the oil has settled out of the clutches or something. There was a mess of silicon on the rear diff cap area. Couldn't tell if it was new or not. I think we put 10-20 miles on it at least and only looked under it for maybe a half hour... Still did the clunk/shudder at a start from a stop, when we returned it.
So, what could be causing this clunk/chatter when talking off from a stop/1-2mph roll?
Axle wrap?
Differential Clutches?
Differential?
Driveshaft?
Transmission?
View 7 Replies
Just last night I noticed that when I was at a stop light my RPM would go high then low and when driving it felt like when she was changing gears alil rough (if that makes sense). This morning she started up just fine but as soon as I put into drive it stalled. Turned her off and started right up and then in drive stalled again....did this three times and I gave up. Last night when I was at a stop light I thought TPS because when I first bought her I had to change it, so it felt alil familiar, but back then (5 yrs ago) she never stalled.
View 5 Replies
I have a Hyundai Santa fe 2004 6cyl 2.7 L , AWD. I am having problem of slow acceleration which is worse after a stop sign or red light. Sometimes while taking turns I feels like that I will not move and I was lucky to be not hit by a Car coming from opposite direction while taking a left turn today.
The Truck’s exhaust pipe broke recently and a auto garage welded it. But I am facing the above problem immediately after the repair of exhaust pipe. If I put more pressure on gas pedal then a mal function indicator comes and today I took it to another mechanic and he gets the error code of P0303 –engine misfire and wants to charge me ~ $600 $ to replace spark plugs and wires. The malfunction indicator goes off also while I am driving and can comes back after a while or a day. With the indicator on, the car drives erratic (minor jolts ) for few meters and then its fine. Since when I am driving on highways then I can go higher speeds without any problem. Is it still misfire issue???
View 11 Replies
2006 4.6l / Stalls at stop signs, red lights, and slow turns. My truck has been doing this for 3 years. Throws a code for crank position sensor, also will say unexpected low idle which would explain why so many of us have low oil pressure while this is happening. So after years of worrying and reading these forums and stalling at stop signs I take to the shop. And it was the throttle body needed cleaned. No more problems. Runs like a new one. I have used Lucas fuel treatment for years in this truck. Im a big fan of their products. When this problem began I was adding Lucas with every tank of fuel.
I buy it by the gallon jug. I used some Lucas from this same jug on the wifeys Denali and her truck stalled out once or twice. She wouldn't ever let me add any to her gas again lol, I argued with her that it wasn't because of the Lucas additive. Never the less it never stalled again. Maybe I got a bad batch, maybe I used too much, or maybe it had nothing to do with the additive. But I thought it needed to be mentioned since it is supposed to be a cleaner, and since I carried it in my tool box and added it to almost every tank of fuel. I was adding about 7 ounces per tank. Who knows? But the problem with this truck is that the throttle body did need cleaned.
View 3 Replies
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
View 6 Replies
2003 Dodge Durango 4wd, 4.7 liter, 130,000 miles ... I'm having a problem with stalling. First started about 3 months ago, when I would come to a stop, the rpm's would fall off drastically, but would rebound right away. About a week later, it would actually stall, but I could start it without a problem. Took it to a local shop where they said my cam sensor needed replacement. That was done and it ran good for about 2 weeks when the same thing started again.
Took it back to the same shop and they told me that the cam sensor had gone bad or the sensor that had been put in was faulty. They replaced it at no charge to me, but they said that the crank sensor needed to be flashed and that had to be done by the dealer. So off to the dealer I went, and they told me that the crank sensor needed to be replaced not flashed. I had them do that and it ran good for about 2 weeks again and now it's starting to stall again.
View 5 Replies
This spring I installed a Ford OEM limited slip unit in my 05 F 150. Recently I notice a brief, intermittent shudder when turning right or left from a stop sign. Does not do it all the time. I don't notice this any other time. The Valvoline synthetic oil I used said the Ford additive was not needed. Is this the "nature of the beast", should I be concerned, should I put the additive in anyway?
View 1 Replies
2002 Dodge Durango 6.9 R/T... I had my bearings replaced 3 weeks ago. And about 1 week later after 40 mins in stop and go traffic I started smelling this hot metal and rubber smell. Then my breaks got really tight when I pressed the paddle. Is this related to having my bearings replaced, what could be causing this to happen every time I am in the car 40 mins or more. It's happened 4 times now and the first time it started smoking. I'm really nervous to drive my truck in stop and go traffic.
View 3 Replies
Ok, so I just replaced the entire timing set (phasers, chains, sprocket, tensioners ect) on my 2004 f150 5.4l about a month ago. I also extracted ALL 8 spark plugs and replaced those with the Champion 1 piece plugs. In addition, I replaced the intake manifold because I did this job when it was 20 degrees outside and I found a crack. Soooo, all that being said I put the whole truck back together and it runs like New. Until about a month later. When the engine gets hot, maybe after about a 30 minute drive or so, it has a really really rough idle until I give it a little bit of gas. Then it clears up. It has only done it 3 times since I put the engine back together. It might go 2 weeks and not do it. No codes. What I could be? EGR? MAS air? Only other thing I can think to say is if you get on it out on the highway, after about 3k rpms it seems like the power drops off quite a bit. Like the engine isn't getting enough fuel. I guess it could be just me, but it just doesnt seem right.. I guess I could try to unplug the MAS air flow sensor...
View 14 Replies
I recently purchased a 2000 Durango with 151K on the clock. It looks like it was well taken care of, clean inside and out, and runs/drives nice. I just have 2 "concerns". There are times when the vehicles shifts from 1-2 and 2-3 it "shudders", only does it for a split second, and seems mainly when pulling out on some sort of upgrade, but not always. Otherwise it runs and shifts fine.
The second "concern" is that it seems to surge a little at idle. At a warm idle in park is when I noticed it. It goes from about 750 rpm to 950 rpm over and over. I haven't really noticed if it does it during regular driving.
View 1 Replies
My Jeep does not always start. All the dash lights come on, but when I turn the key to start the engine, they all go off. The lights stay off, and the engine will not start. The ignition won't even click... it's similar to a dead battery. When I turn the key back to its original position (when first inserting), all the gauges spike and the needles jump really high for a split second. When the door is open the gauges keep jumping (spiking). After waiting for 30 minutes, the engine will start fine like nothing was wrong (except the fluctuation in idle). It would rev high at idle sometimes, and sometimes it would idle low... so low in fact the jeep stalls. I have read about the symptoms of crank/camshaft sensors and relay, but I wanted to make sure from people that know more than I or have faced this particular problem.
View 5 Replies
