I have a 1991 Dodge Dynasty with a 3.3 Liter engine & the serpentine belt keeps coming off. I have replaced the belt,idler pulley & belt tensioner. When the road is wet or winter slush (it happened once in dry hot weather) the belt will ride off.
View 4 RepliesMajor screw up. Added steering fluid to brakes. Drove the car for about 300 miles. Car actually over-heated. Discovered the mistake after. Bleed brakes and added correct fluid. Not heating up now, but only bled the brakes one time. This is on my grandsons 91 Dynasty. Now worried the brakes are going to just go out.
View 12 RepliesThe nut that holds the pulley in place on the alternator has fallen off, causing the pulley to become loose and now the serpentine belt will not stay on. What is the size and thread type for the nut that I need to replace?
Alternator Pulley Nut for 2004 Camry 4cyl
'92 Dynasty is a good runner, but, once the engine gets warmed up, I shut off the engine at my own risk. If the car sits for a while with the hood open, it will start again, but attempting to start immediately after shutting off will result in the engine spinning over but no sounds of attempted ignition. It seems that once the coil is cooled down to slightly more than body temp the engine will start like nothing was wrong.
View 3 RepliesThis has happened to me three times now. The first time was at a stop sign, the second going 70mph on the highway, and the third time at a stop sign. I will be driving and then all of a sudden the engine loses power. The more I push on the gas, the more the engine wants to die. If the engine stays running after I pull over, it idles very rough, and still if I press the gas, it wants to die. This seems to only happen after driving long distances for maybe an hour or so.
When this happens, if I let the car sit for about an hour, it will start up just fine, idle smooth, and drive normally. This is a 1992 Dodge Dynasty with the 3.3L V6, Fuel Injected engine. The car only has 78,000 miles on it and is in excellent condition. It's such a nice car that I would like to figure out what's going on with the engine because I would like to drive it for a lot longer. So far I have replaced the ignition coil pack, the oxygen sensor, map sensor, fuel filter, and spark plugs an wires.
Serpentine belt on a 2006 Honda Odyssey fraying and then ripping into the timing belt causing that belt to break? I recently had this scenario given to me as the cause of my recently replaced timing belt breaking.
View 11 Replies2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
I have a 1991 toyota celica st and I recently broke some belts. I think I broke 2 belts. Any diagram of the belts and pulleys because I don't know where to loosen the pulleys to replace the belts. What each belt powers?
View 3 RepliesI am very concerned regarding how often my serpentine belt needs to be replaced. First time it was replaced at 104k, second time dealer replaced it at 126k, third time at 153k. Today I went for oil change (173k) and the dealer told me that it has little cracks and recommend replacing it. Is it normal? Could it be something else is affecting it?
View 11 RepliesI have had my Tiguan S for almost 2 years and it seems that I keep having to get it towed. I just had it to today because the serpentine belt came off when I was driving. After I bought it the fuel line was loose and it had to get put back on and after about 12000 miles my tranny went out and had to get replaced.
View 2 RepliesI have troubles with what I thought would be a basic job: removing the belt on my 2004 Solara so that I can remove the alternator. I can't get the belt loose enough to slide it off, no matter how hard I try.
The wrench I'm using is about 12" long, I'm a big guy and I've done powerlifting in the past, meaning I can apply lots of strength on that wrench. I've just watched a youtube video of a guy with the same engine removing his belt, and he exerted a lot less effort for a lot more wrench travel. I thought that using a breaker bar is extreme.
Pulled off front bumper today with no success, seems like the whole radiator and a/c unit must be removed?
View 5 RepliesSo the PO of my Jetta had the alternator replaced...awesome! One less job for me to do. My serpentine belt went out yesterday so I chalked it up to being old. When I got the new belt on it kept slipping off, I pulled the tensioner pulley off and saw that the wheel was all chewed up, I look down and saw that whoever put in the alternator didn't bother to screw in the bolt all the way and it chewed up the belt and everything else.
View 1 RepliesMy daughters 96 cav has a bad squeal coming from serpintine belt. I tried belt dressing and it threw the belt. I didn't notice any cracks/dry rotting on belt. I put the belt back on but it is still squealing.
View 1 RepliesI have a 2010 camry SE & have found nothing about how to change the serpentine belt on the 2.5 engine.
View 1 RepliesCan a frayed serpentine belt cause a clunking/grinding noise? The clunking grinding noise has been going on for about 2 months and it goes on and off, Last night it started squealing and I checked the drive belt and it is frayed on the outer edge.
I have a 2005 Prius with 86,000 miles. All of these issues started about 2 months ago, the day after an oil change.
Serpentine belt break? My 2005 Prius has 132,000 miles on the original belt, so I thought it's probably due for replacement. I went to an independent garage to get an estimate ($80). But the owner said that he has never heard of one actually breaking. He said that they are reinforced with fiberglass, so they just don't break. He recommended that I look for missing chunks and listen for squealing.
View 2 RepliesI looked through the MKIV DIY stuff but didn't see one. My serp belt is in need of replacing soon. Seeing some cracking on it for sure. According to records from the PO it was bought as part of the timing belt kit at the end of '09 so I imagine it was changed then...just didn't think it would be so cracked so fast!
Anyway, looking to replace it in the coming weeks. If I could be pointed in the right direction that would be awesome. I do have a Bentley, but I find how-to's on here to often be better. But if I need to just follow the Bentley, I can do that too.
I've been hearing a slight squeaking near the belt area. It's not continuous. Does it for a second then stops for a second and continues.
I hear it a lot more when I put the heat on through the top window (defroster). Never noticed it until it started getting cold. You think it might just be the belt? Or what?
I need to replace the serpentine belt on my wife's 2001 Santa Fe 2.7 V6 but I can not seem to figure out how to get the tensioner off.
View 1 RepliesSo this car has only 50k miles. It was really cold in the sierra (around 20F) and the car started making a squeaking sound. I assumed it was just belt warming up, but when I opened the hood later, I saw shredded plastic. No CEL's! Seems to run smooth.
Where this came from? Is it part of the serpentine belt system?