Dodge - Dakota :: 2004 - Clunking Noise When Going Forward While Turning Either Direction
Jun 21, 2011
My 04 Dakota 4x4 makes a clunking noise when
1) in 4-wheel drive going forward while turning either direction (but not while going straight) and
2) in 4-wheel drive in reverse (straight or turning). It does not do it in 2-wheel drive under any circumstances.
I suspect the front drive shaft U-joints since it only happens in 4-wheel drive. Rear drive shaft U-joints or front CV joints would be a possibility but I would think they would cause a noise in both 2 and 4-wheel drive and in either direction equally.
View 1 Replies
Advertisement
My tensioner pulley is already shaking but when the ac clutch is engaged the tensioner starts to shake even more and it starts to make a clunking noise extremely loud and fast. I also noticed that the crank pulley is shaking quite a bit too so I don't know if that has anything to do with it.
View 4 Replies
I have a 2000 dakota in the morning after the first start, moving foward the truck rocks and feels like trans. slipping. After 5 mins, just fine. Change the Trans. Ffilter?
View 1 Replies
I have a 2004 2WD supercab. And am hearing a 'clunking' sound when I turn almost full-lock. Below is a summary of what I have experienced so far:
- My truck used to be lowered 2" (below stock) at the front since new. Last month I lifted it (front and rear) and it now sits 2" above stock on new rancho shocks.
- I installed a camber kit and had the front aligned (toe and camber) after the above suspension work.
- The truck drove beautifully for two weeks until one day a 'clunking' sound was heard from the front-left every time I turned left. The alignment also changed as I had to now hold the steering very slightly to the left to drive straight.
- The alignment shop re-did the toe tracking (the camber did not change) and the truck drove great for about a day. Now I can hear the same clunking sound when I turn right and the tracking is again screwed up meaning I need to hold the steering very slightly to the right to drive straight.
What parts are playing up and what may need replacing?
View 2 Replies
I noticed a humming like noise when my transmission is engaged. I looked under the truck and saw a wet spot on the transmission(leaking)It is a manual transmission 5 speed Dodge Dakota 2001.
View 2 Replies
Gasoline backs up in the filler neck while pumping. I've disconnected the vent tube on the filler neck and disconnected the hose going to the canister next to the fuel tank. I've let the engine run during fill up, but this does not change things. Violently shaking the truck while cursing only provides entertainment to other motorist at the pump. I gave up my career as an auto mechanic in the 80's when cars were being made out of metal.
View 5 Replies
When I start the truck in cold weather, the transmission doesn't want to shift out of 1st gear. Some time it take driving it a 1/8 of a mile before it shifts.
What is wrong / need replaced ? I was told to shift it thru all the gears before I move it to warm up the transmission fluid ? I'm thinking some sensor needs replace ???
View 4 Replies
I have an 87 Dakota with a two-piece driveshaft, bought it new. A couple months ago at 140,000 miles there came a chirping noise from the rear at acceleration from a stop. I changed the u-joints with new Moogs and had a new center support bearing pressed on at a driveline shop. Reinstall driveshaft same as it came out. The u-joint at the diff was shot, the other two not far behind. The chirping vanished as expected, but was replaced with a slight vibration felt in the seat starting at 50-55 mph. I dropped the truck off at the driveline shop to get the driveshaft balanced. They put it on the balancer and called to say they couldn't balance it, the indicator kept jumping around and wouldn't stabilize. I asked them to reinstall it and came to pick get the truck. The guy who worked on it said that this was usually a u-joint problem. I asked what brand they used and pulled he out a Neapco u-joint box and said they use them exclusively and have never had any problems. I ordered Neapcos from RockAuto. Will replace the Moogs and see what happens. After they reinstalled the shaft I drove in the freeway and it acted exactly the same.
I was very careful when pressing out the old joints not to stress any of the yokes, applying pressure to the u-joint members at right angles to the cap being pressed out and not to the cap 180 degrees opposite. When installing the new joints, after inserting the clips (interior) I pressed all clips snug against the yoke. The joints all moved freely in all directions. Again, the shaft was replaced exactly as it came out.
View 19 Replies
I have this whistling noise coming from the front area of my truck (97 dodge dakota) 4X4. The noise sounds like air at high pitch (just my opinion and friends), happens around 30 to 40 mph when you hear the whistling noise. I've taped all holes and gaps that might be causing the sound but no avail. I've had a friend look at it, that's a fire truck mechanic and no luck and he said it didn't sound like wheel bearing problem.
View 1 Replies
On empty a week ago, filled 1/2 a tank, drove home no issue. Didn't drive truck for a week. Turned it on this morning (didn't warm it up) about 10 minutes into the drive anytime you tried to accelerate, the truck would buck. If you were idling or just had your foot slightly on the pedal driving at the same speed it was fine, it only bucked when I really pushed on the pedal to accelerate. The check engine light started flashing as well.
View 3 Replies
I drive a 1997 dodge Dakota 5.2l 5 speed manual 4wd and recently it started making a really aggressive banging or popping noise while I was driving, it also made the truck bounce up and down a little bit and I could feel the shifter move up and down while this was happening. So I went underneath and discovered my transmission mount was out so I changed that and as well I changed a few u joints. One thing i noticed while I was replacing u joints was that when I had the front drive shaft off the whole problem was reduced to just a minor popping noise but once I slapped back on the front drive shaft it all came back. Another problem that is occurring because all of this is that when I tried to use the 4wd in 4 hi it just kicked it out of 4hi but in 4 lo it would stay in but all the problems were still there. The only time it doesn't do anything is when I am already rolling and I put the 4wd selector in neutral to disengage the drive shafts.
I have asked a few different people their opinions and I get different answers, someone thought it could be something to do with the steering shaft or intermediate steering shaft but I think that is not the correct diagnostic. Another one of my buddies suggested that it might be a stretched chain or gear in the transfer case that is causing it.
View 6 Replies
I have an 87 longbed Dakota that I bought new. It's my work truck. Lately it has developed a chirping noise that I hear best with the rear slider window open. I think it is safe to say that it is not coming from under the hood. When I accelerate from a stop the chirping noise increases in pitch and frequency. The frequency does not change when the auto trans up shifts. There has been no noticeable out-of-the-ordinary vibrations, even at freeway speeds.
I have stopped driving on the freeway since the chirping became impossible to ignore. The chirping becomes less and less audible the faster I go as the pitch and frequency increases. When just starting from a dead stop, it sounds like a metallic scraping noise. Whenever I take my foot off the gas the chirping stops, even when still coasting, so it only occurs under load. It does not occur when the truck is stopped and the engine is revved.
View 9 Replies
I have a 03 Dakota 4x4 that is rumbling badly from the right front. The rumbling increases and gets louder steadily with speed, transfers slightly through the steering column, and goes away when turning right and taking the weight off the right front tire. It is also doing this when in 2WD. I have replaced the bearing hub assembly but that didnt fix it. I have also pulled out the CV axle, but am unable to tell if this is the problem. I'm also not finding any worn bushings or ball joints, or at least not enough wear to justify this horrid sound.
It is my understanding that a worn CV will produce a clicking noise when turning. I haven't noticed this at all, yet I can't imagine what other moving parts could be causing this rumbling. I have also taken a look at the spline on the differential, and other than the normal tiny bit of movement, it looks fine.
View 2 Replies
The truck had a hard time starting, turn the key over hear that it wants to, but won't. Once getting it started, truck would drive fine, but after about 10 minutes just dies while driving. It then took 6-7 tries to get it started again, drove back like no issue. What it could be? I have come up with, potential battery, fuel pump/filter, spark plugs, EEC relay, PCM, or AIS motor, O2 sensor....
View 2 Replies
My 06 Dodge Dakota, has a terrible racket coming from the front end when you hit a rough place in the roads especially the left side, seems worse when the wheels are cut, nothing is obviously loose ,it has 88K miles on it.
View 6 Replies
I have a 99 dakota. The truck wont turn over, headlights/doom lights nothing in side works. But when i open the door the glove boxes starts making a clicking noise ? it happened once before and once i pushed it down a little drive way everything turned back on ? What could cause this problem ?
View 3 Replies
If I am moving in reverse and tap the brake I hear a clunk from the rear of the car. If I continue in reverse and then again apply the brake then no clunk. If I drive forward and stop, no clunk. If I then shift into reverse again and apply brake I get the clunk again. Had the struts/shocks replaced but no change.
View 5 Replies
I recently purchased a 2005 Dodge Dakota SLT with 50k on it. The truck is in great condition inside and out. I have noticed depending on certain days, different weather conditions that it will make a squeaky noise when going over the bumpy roads. First thing that came to my mind was the sway bar end links. I purchased them from NAPA and installed them. Still the truck is making this noise. What it can be? Almost sounds like it is in the rear of the truck but hard to actually pin point the location. I have tried with all windows down I cannot tell.
Sound is exactly like this video: [URL] ....
View 3 Replies
My 2008 Prius with 105k miles recently started having a strange clunking noise when turning at low speed. Dealership diagnosed it as the steering shaft and yoke to replace.
View 7 Replies
So I got a steering problem and it's got me going crazy. I have a 06 g35 sedan lowered about an 1.5 inches. It's been about 5 months since I lowered it, lately I've been herring clunking noise in front suspension, not all the time but only sometimes when I turn. The other day my steering got really stiff and when I turn the steering won't return to the center. My Power steering isn't making any noise and I'm good on fluid. A lot of people say my ball joints but don't they usually make a lot of noise when they go bad ?
View 18 Replies
We have a 1995 Chrysler Concorde. It drives fine, but recently I have been hearing a clunking noise (two or three clunks) somewhere in the rear of the car AFTER I turn the car off. It does not clunk while driving or braking or slowing down: only right after the ignition is turned off.
View 5 Replies
