Dodge - Dakota :: 2002 - Brake Warning And ABS Light On
May 11, 2015
I was asked to look at this Dakota because the Brake warning light and the ABS lights come on.
I get no stored codes with my code reader, and upon test driving it I found that the lights both go off when you shut off the truck, but each time you start up and drive off....those two lights will come on the first time you hit about 30mph and then stay on until you shut off the truck again. Restart and the lights are off until you drive off and hit about 30mph again.
Backing out of the shop, stopping, turning around, down the driveway 50yds and stopping at the road....the lights stay off, even though I just used the brakes three times at least. Get on the road and hit 30mph and they go on.
The two fuses, one in the fuse block by the drivers door and the other (ABS) fuse in the Power distribution box test good.Both brake lights work at the rear as does the high mount brake light. Fluid is at the full mark.
I pulled all four wheels and drums on the back and inspected everything and everything looks good and the E brake cables are intact and working as they should. Brakes were replaced (not by me) and have a little wear, but plenty of material left. No leaks of any lines, calipers, or cylinders. Front rotors are not scored from a sticky caliper, they do have a little minor rusting but because it has been idle for a few months.
I have the same year and drive train in my Dakota. Their truck has about the same stopping power as mine, but I did notice that I did not feel the surging in the ABS as I feel in my truck. I tested this by traveling at about 40mph with the passenger wheels in the gravel and drivers wheels on the pavement and applied the brakes hard. In my truck I felt the surging, but not in theirs. Note that my truck has a tall cap and always carries an extra 800 pounds of gear in the back.Maybe the heavier weight makes my ABS kick in quicker, but I would think weight wouldn't matter.....one wheel is slipping...period.
View 15 Replies
Advertisement
Question regarding a 2002 Dodge Dakota, 2wheel drive ext cab 100,000 miles 6 cylinder engine. Cruise control stopped working, get the indicator light on dash, but no cruise.
Would I start with the Clock Spring? Will Durango parts interchange? ABS Light, was told the problem is the main unit that mounts on the driver side fender. Have tried replacing with other units from the local scrap yard, but still get warning lights/sounds.
View 3 Replies
I have a 98 Dodge Dakota with 5.2 V8. On the way home today all my gauges and warning lights started going on and off and then gauges stopped working all together and all the warning lights stayed on. The engine was running fine and after pulling over and checking things out, I made the last mile or so home OK. Checked fuses and battery connection and everything looked Ok. Relay or Computer?
View 4 Replies
Have a 2002 Dodge Dakota automatic. This winter when temps. dropped into lows 10s and zero degree weather, the Dodge truck would start,but would not come out of park gear. Have replaced interlock solenoid and brake light switch. Still have same problem when Temperature drops into low 10s &below. Otherwise,everything ok. (not using ER brake).
View 5 Replies
The parking lights come on, the turn signal lights work, the interior lights and high beams work. Could it just be a fuse or two? Dodge Dakota 4WD 2002 ...
View 3 Replies
I have a 02 Dodge Dakota 4.7 liter that is killing me. No codes and no check engine light. From a cold start it starts fine but then runs rough. If I let it run for a few minutes, turn it off and try to restart it, it is very hard to start. Also, if I have it running and rev the engine above 3k rpm and let go of the gas it dies. It will idle without holding the gas pedal down but will die after a rev. Fuel pressure and volume are right in spec. Have good compression, spark and injector pulse on all cylinders. I thought maybe a crank or cam position sensor, but either of those would usually throw some type of code. I thought IAC but it seems to be functioning properly.
View 3 Replies
I have an 2002 Dodge Dakota 8 cyl. 4.7 L engine, 272K. I've gone through 4 fan clutches in the last 2 years and could have gone through more. My mechanic can't figure out why. I've replaced all hoses, radiator, water pump, T-stats, you name it. AC doesn't work either. Probably just a leak. Not sure yet. Why they keep dying on me.
View 19 Replies
So I recently attempted to change the brakes on my 96 dodge dakota. I followed the instructions in my Chilton manual to do it. The driver side was no real problem and managed to get it done within an hour. Now knowing how to do it I moved to the passenger side. Once I slid the caliper off the rotor I noticed that the pads on this side were nothing but metal but the rotor was fine. I took out the pads but the piston was hyperextended and there was no way to compress it no matter what I did. The piston eventually just started to crack away. So I went to O'Reilly's and bought a refurbished caliper. It looked very similar and fit the bolts. However when I tried to attach the brake line it was at a different angle then its fitting. The brake line is a thin metal tube for the last 6 inches with a square piece of metal at the end where the hollow bolt goes through and then into the caliper. But because of the metal section I cant angle the brake line correctly to get a good seal.
View 6 Replies
My 2002 Dakota with a 3.9 (200,000 miles)has a problem that I cannot seem to cure.When I start the engine it never hesitates....it starts without a problem. No excess cranking...it fires up as it always did.It does run a bit rough as if ONE cylinder is missing every few revolutions. If I let it idle in the driveway for five minutes it will clear up and run fine. But if I take off right away the following will happen.I put it in gear (automatic) and for the first mile or two it runs as though the plug wires (More than one) are wet and arcing. I can barely get above 25mph. it will spit and sputter for that first mile or two.
Then suddenly it will clear up and surge....probably because I have loaded the system with excess fuel......and after it clears up , I have no other problems with it weather I'm on a long trip or a short one. If I stop for more than 15minutes, I have to go thru all this again.I've had vehicles that acted like this after a hard rain because the plug wires were old and arcing...that's why I use that as a description.I also noticed that the other day right at the end of a big downpour it took at least 5 miles to clear up.
Before this rainstorm I had replaced the plugs, wires, rotor and cap, while inside the shop so everything should have been bone dry except for all the humidity from the storm. After starting I checked for any arcing while in the dark shop and even moved a few wires that were touching and no arcing was seen from the cap, wires or coil. I also changed out all those parts 6 months ago when I did a major tune up, but it ran fine untill about two months ago.
When this started two months ago is was just a rare occurrence and my mechanic thought that I had gotten some gas with water in it. He had me run a few bottles of injector cleaner it the next few fill-ups and I've run a few bottles of heet through it also. In the last two weeks it has been doing this every time I start up. When this did start showing up it would show a code of a random misfire and the engine light would come on even though I felt no signs of a misfire myself. The light would stay on for a day or two then go back off. A few days later it was back on.I thought that I fixed the problem because the light stayed off for a month.
So it has been only the last two weeks that it bucks and kicks so bad at a startup, but you would think that an engine misfire would show up and the engine light come on. By the way the light does work. Now, I never get a engine light on, and he found no codes in the history. I have my own scanner, but his can do so much more. I never find any codes also. My mechanic ran some diagnostic's and found an up-stream 0,2 sensor bad so we replaced that.
Yesterday I dropped the tank, pulled the pump and cleaned the tank real good. The only filter is the sock on the pump and that was clean. I refilled with fresh gas and I still have the same problem. So I think that we can eliminate water in the fuel, plugs, wires, rotor, and cap. My next thought is the cam sensor in the distributor.
View 3 Replies
My brake pedal goes almost to the floor when I'm braking.I replaced the rotors, pads, shoes, power booster and the master cylinder 3 times.Had it bled twice and I still have a soft pedal, but now it firms up a bit as I pump the brakes.
View 7 Replies
I purchased a 2002 Dakota and have had a hard time ridding it. I thought that the heater core was leaking and getting the passenger side floor wet, but it's the overflow for the evaporator under the dash. The drain must be plugged. Will I have to remove the dash to pull the heater unit down far enough to clean it. I don't think I can do much from under the hood...too tight.
View 4 Replies
This Dakota has the 3.9 with about 240.000 miles. New battery and Alternator within the last 18 months.
The other day after driving about 12 miles the chime "Check Gauges" come on and I noted that the voltage gauge on the dash was buried at Max.Pulled over shut off the truck and popped the hood. No visible problems. Got back in, started the engine and the gauge went back to it's normal position. I had expected to see smoke from the alternator or the battery blown to pieces from the overload. I also noted that there was no excess heat at the alternator or battery.
I picked up my DVM from the shop to carry along and have driven at least 5 trips over 15 miles since. Today the same problem occurred, but by the time I pulled into a close-by parking lot the meter went back to normal. I checked the voltage at the battery and had 13.25 volts with the engine off and 14.40 volts with the engine running. I drove another 40 miles with no problems.
Tomorrow I plan to run a lead from the battery into the cabin, so I can monitor the voltage quicker if the problem reappears.
View 11 Replies
After I drive my truck and park it for any period of time and then restart the truck it will sputter and backfire rpms do not go over 1500-2000. If I put it in neutral and rev the engine this will work but not always correct the issue. Eventually if I just push through it after 2 or 3 min it will go back to normal. I replaced the spark plugs, wiring and distributor cap. I have also changed the O2 sensors nothing seems to work though.
View 6 Replies
My 2002 Dodge Dakota Extended Cab pickup is throwing several different 02 sensor codes. The first one was P0132. I reset the CEL and it ran good for about 1800 miles (100,140) on the odometer now. Now I'm getting a P0158 code and CEL went off after a few miles. Now it's back to a P0135 and P0138 code. Are the 02 sensors really bad or is there an underlying problem with the wiring or the computer. The truck runs like new when the CEL is off. The P0132 has never shown up again. The engine is the 3.9 V6 and is 2WD.
View 3 Replies
I have a 2002 V6 Dodge Dakota that just recently lost pretty much all power. It will not go above 20 mph and has a hard time going up any hills. I was driving on the interstate and initially was having a hard time reaching 65 mph. The truck would roar and then shift and then lose power and shift down a gear. Eventually it lost almost all power and is now barely drive-able. It makes a sound like an ATV at low speeds, kind of a deep humming sound. When I punch the gas in neutral in makes the same sound. I have had problems with it stalling before and am at a complete loss as to the cause.
View 2 Replies
There is a clicking sound (about once per second) in the front of the engine compartment of my 2002 Dodge Dakota (2WD, quad cab, manual, no alarm, no electric windows, locks, mirrors, etc.) when the vehicle is off (ignition in the off position - with or without key in ignition). It stops if the battery is disconnected, if the key is in the run position, or if the key is in the position that allows one to use power while the vehicle is off. The interior lights and headlights will flash in sync with the clicking sound if they are on as well. The chime that lets you know that the key is in the ingnition with the door open will miss a beat with the click also. The amps running through the circuit (no lights on) jump up from 27 milliamps to 39 milliamps with the click sound. A possibly related issue is that the headlights no longer stay on for the 30 seconds or so that they used to when I turn off and exit the truck after having driven with the lights on. The clicking and light flashing continued even though I removed each fuse and relay in the box under the hood and the one next to the driver door (the lights stopped when their fuse was removed, but the clicking continued).
View 3 Replies
I had a front brake job done on a 2002 Dodge Dakota pickup at 85000 miles. When I stepped on the brake, I felt pulsation in the pedal and a sort of wobbly feeling in the steering wheel. Also the brakes were making noises while driving. Classical sign of a warped rotor?! Long story short brand new rotors, brake pads and calipers, later the pulsation is mostly gone but the braking is still not smooth at one point while the tires are turning. Now i do have to older tires on the front but i just bought two brand new tires for the rear. Would it be wise to put the new tires on front to see if there might be some unevenness caused by the old tires before i take it back to the shop?
Also the feeling of the brakes catching on one point seems non existent or so minimal I can not be sure if the road surface interfering while driving slow of applying the brakes gently. But slowing down from higher speeds (above 40 mph) and using more then gentle braking ( not standing on the pedal with both feet) it is definitely there. Before the brake job braking caused the steering turning right. (sign of more braking action on the right - right?). Now with new stuff still pulls to the right but not as strongly. Should not this disappear with the brake job? Or get the new tires on front and see what gives?
View 9 Replies
4 days ago I had a complete front brake job done on a 02 Dodge Dakota pickup. 80 miles on the new brakes I stuck in a traffic jam for over an hour. Once I stopped at the store I smelled burning brake odor on the passenger side right front wheel. Is there anything that should burn off of a new part of shall be concerned about this? New brakeshoes, rotors, calipers + brakefluid.
View 9 Replies
Last year, July, replaced Trans.modulator..All went well. Now..sloppy shifting, occasion heavy thump changing gears when slowing. Trans. people say All good according to their programs.....but they also feel the same problems. Its an internal problem, they say, too expensive to tear down.Drive it until it dies. ( 161 K on the odometer.....otherwise is perfect. I want to do a flush, then drop the pan, change the screens, tighten the bands and replace Trans. fluid.
View 1 Replies
So, my oil light comes on after startup like usual then shuts off. Anywhere from 2-5 minutes of the vehicle running light comes back on and does not shut off unless I restart the vehicle. Have changed oil pressure switch and oil pressure is reading in the normal range..
05 dakota with 175000 kilometres
View 19 Replies
My ABS light came on and my parking brake light as wellAlso my Speedometer Quit working all at the same time what happened?????I drive a 1998 Dodge Dakota 5.2L 4x4 5speed manual
View 3 Replies
