Check engine light computer scan indicates intake manifold runner control valve stuck open. Will it damage the car to drive it in this condition and what does fixing it entail?
View 4 RepliesCheck Engine Code P2006 intake manifold runner control stuck on closed? Taking it in to have it checked out.
View 10 RepliesWell, I had a check engine light that lasted only three days then it cleared itself without any intervention. I checked it with a vag-com and I discovered there was an issue with the intake manifold control. I ended up bringing it to the dealer since it is a fairly new passat, and the service department informed me that the Intake Manifold Runner Control needed to be replaced.
Below were the fault codes.
3 Faults Found:
012599 - Intake Manifold Runner Control: Basic Setting not Completed
P3137 - 001 - Upper Limit Exceeded - Intermittent
Freeze Frame:
Fault Status: 00100001
Fault Priority: 0
Fault Frequency: 1
Mileage: 33815 km
Time Indication: 0
[Code] .....
I have 98 windstar, p1538 code, IMRC. I have physically checked both IMRC's and they are functioning as they should. (if they were bad, they would not move at all right?) Assuming they are good, which step in the troubleshooting process I go to now? The van runs perfect, just that darn light! Do I start going for the O2 sensor now? What to next in the chain of troubleshooting?
View 14 RepliesI have a 2011 Tiguan S 4Motion with just over 63k Miles which for the most part has been problem free and great to drive since I leased it at 40k miles. About 2 weeks ago my CEL came on and I used the Torque app on my phone to check the code and it was the apparently well known P2015 intake manifold runner position switch code. The car was running perfectly fine so I cleared the code and it stayed off for about a week before coming back on with the same fault again yesterday. I have a couple of questions for the much more knowledgeable than I people in this forum around this code.
First - I've read in several places that VW has placed an extended warranty on the manifold and fuel injectors for the 2.0 TSI and that this code is usually an indicator that the manifold needs to be replaced under this warranty. What I haven't found though is conclusive info on is whether the 2.0T in my 2011 Tiguan is covered under this extended warranty. Since this code so conveniently is popping up just 3k miles past the end of my 60K mark, I'd like to know this. I leased the car from Enterprise, not a dealer so I'm worried that whatever dealer I take it too will try to bend me over on the service so the knowledge that the manifold is still covered would be at least some comfort.
Second - I won't be able to get it in to a service department until mid next week and I have a 300 mile trip to make this weekend. The car is driving fine as far as I can tell so I'm not overly concerned. I do my own basic maintenance i.e. oil changes, plugs/coil packs etc. but I'm thinking changing the manifold would be a little bit out of my comfort zone..
I bought a 2002 Ford Windstar, it has over 154,000 miles on it. My problem is I got a ODB II code reader and it said that the Intake manifold on the left bank is stuck in the open position. How do I keep it from sticking.
View 15 RepliesI am just wondering at what revs the stock intake manifolds are meant to switch over as i think mine is stuck and not moving.
View 23 RepliesI have to replace the valve cover gasket this weekend.
View 5 RepliesCan oil leak out of Intake Manifold? i have Oil around lower intake manifold gasket. is this serious issue?
View 11 RepliesI have a P2440 code from warning light- Secondary AIR System Switching Valve A' Stuck Open. This started to appear when I took it into the dealer for other issue with transfer case whining when in 4x4. Can this code be associated with something the mechanic did , would they remove any sensors or wires, that may not have put back. Not happy. Are these trucks know for this code? Estimate cost?
View 4 RepliesI got new brakes put on a few months ago month (semi-metalic)... Any way anytime I drive and it is raining, when my car comes to a to a complete stop, and I hit the gas to shift into second gear my car sort of stutters like it doesn't want to shift but then it does.
I took it to two mechanics MULTIPLE times who even drove it in the rain and they couldn't find a single thing wrong. they hooked the transmission up to the computer and noticed nothing.
It has happened multiple times and its both been raining. Could it be the tires aren't gripping the road and that's why my cars shifting funny, like the tires aren't caught up?
I have a 2008 dodge avenger that stalls without warning while I am driving. It happens without any warning signs, happens when I am driving and also when I stop the car. The dealer can't find a thing wrong with it. What's wrong with it? It starts right up after this happens and they tell me my vin number isn't part of a recall for a problem that I have read that other people have with their 2008 avengers.
View 1 RepliesIt makes a weird 'fppp' air shooting noise before the exhaust note and my 2003 gti vr6 makes the exact same noise. It sounds like it's coming from the intake manifold valve and not really the filter, but I'm not sure and yes my filter is clean, the noise also sounds a little bit more obnoxious and problematic in real life. What it is, I thought it was a vacuum leak but I don't wanna bring it in till i know exactly what it is,
View 2 RepliesI have a fudged-up looking oil leak that my oil change guy says is probably a blown intake manifold gasket. Is this the same as a head gasket? I thought a head gasket was around the pistons. I see there is a product on the market that you can put into your radiator that plugs up leaks in the head gasket (Steel something). Is this an OK fix? It would cost $90 for a bottle of the stuff. And what is a reasonable, or low, rate to replace this gasket? And, how long can I drive the car with this condition? It has lost a quart of oil in the past month, driving about 600 miles.
View 3 Replies2008 Dodge Avenger SXT Sedan GEMA 2.4L DOHC I4 / 4 speed automatic75,000 miles Moderately well taken care of (oil change every 3,000 miles, mostly follows recommended maintenance in owner's manual)
Symptoms:
*Car runs and drives fine while the car is in constant motion and decelerating.
*Rough and Slow Idle at a stop on the brakes with car in Drive. Engine speed will drop below ~400 RPM, then "kick" up to ~1,200 RPM, settle back to 'normal' idle ~800 RPM, repeat. I have suggested she put the car in Neutral at a stop to see if that changes anything, but I don't have feedback from her yet. One instance of seeing a puff of smoke from under the hood while the car was doing the above.
*When pulling away from a stop, the car will hesitate; that is the accelerator will be pressed but the throttle response will be delayed.
*When pulling away from a stop acceleration will be inconsistent; instead of rrrrrRRRRRRRRRR, it's more like rrrrRRRRrrrrrRRRRrrrrrRRRRR
*Couple instances where the car just shut off while she was parallel parking (low engine speed).
*One instance where the car did not start on first attempt. Started fine on second attempt.
*No Check Engine Light. The codes have been run.
Shop Visits (at an independent garage recommended by her roommate who's been going there for 5+ years, good reviews on yelp, and always busy):
*First visit: told her they put in a bottle of fuel system cleaner and to use a tank of high octane gas. That didn't really work.
*Second visit: cleaned the throttle body. That was 3 days ago, so far no conclusion either way.
Other repairs:
*The battery was checked (at O'Reilly) and replaced after the starting incident mentioned above. (5 year old car, seems about right).
*2 nights ago I told her to put in a bottle of HEET to get water out of the fuel system (California uses ethanol blend) and a bottle of Gumout Fuel System Cleaner and to fill up with premium gas (based on items below). Be sure to run that tank down to almost empty.
Things I could think of:
*Crankshaft/camshaft position sensor failing.
*Alternator failing (because this problem doesn't seem to exist at higher RPM's)
Research online: It seems that a number of people have similar problems with Chrysler products with this and the previous generation 2.4L engine but no clear conclusive repair. Some of the items mentioned:
*Idle Air Control (IAC)
*Exhaust Gas Recirculation (EGR) valve
*New sparks plugs and wires. (not replaced but should be)
*New timing belt. Timing belt is one tooth off.
*Water in the Fuel System (hence, HEET)
*Dirty/Clogged Fuel System Component (hence, fuel system cleaner)
*Failing Fuel Pump
*Dirty/Clogged Air Filter (replaced per maintenance manual)
*Low Oil Pressure/Failing Oil Pump
*Additionally, there are no recalls against her VIN.
2012 dodge caravan. Bought it used last year with 27k miles. Day after I bought it, it threw a misfire code. They said the spark plugs got wet when they washed the under carriage. Dried it out, cleared the code.
For the next month the car went from a slight shimmy during idle...progressed to strong shaking (its shakes, pauses, shakes...etc.) Finally another misfire code. Took it in and this is what the report says.
"Cylinder misfire on #4. Performed compression test found #4 cylinder compression at 100 PSI. All other cylinders at 150 PSI. Recommend to replace front cylinder head. Has burned exhaust valve seat. Replaced left cylinder head assembly."
About 2 months later check engine light comes on, car is over heating. Coolant bone dry. Replaced coolant, took it back in. They replaced the intake manifold?? Been slowly losing coolant. I have to replace it about every 2-3 months. I notice the car shakes worse when the coolant is low, with minimal shaking when coolant is replaced. Finally took it back in a few week ago when my husband got back from deployment. They said it was a loose bolt on the intake manifold causing the slow leak. They couldn't verify my complaint about the shaking.
Now, car still shaking. Its minimal on start up, gets worse the longer I idle. I can only feel the shaking while in idle. If I restart the car it goes back to minimal before progressing again. Took it back in. They verified the shaking, hooked it up to a computer, no codes or anything. Told me its normal. It CANT be normal, right? I neglected to check the coolant level before I took it back in. I left it with them saying they will look it over, but they don't think anything is wrong. This is exactly how it progressed when they ended up replacing the cylinder head. I have 1k miles left on the warranty, and am moving in 2 weeks 1500 miles away. I don't have time to wait for another code.
Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.
View 6 RepliesI understand that exhaust runs through the EGR. what I don't know is:
Does the EGR valve control the amount of exhaust into the air intake?
If so, does only the amount of exhaust let through the valve go through the EGR?
if so, if the EGR valve is closed then no exhaust will go through the EGR?
I have a 2006 F150 screw 4.6 auto 116k miles that has evidence of a small coolant leak where the intake manifold joins the head. This is on the drivers side directly under the thermostat housing. The t-stat housing is dry and the hoses all appear dry. It's just wet right at the gasket where the manifold joins the head. Reservoir is still normal so it's not leaking too much just yet.
I searched this site and youtube but didn't find any other posts. Lots of problems with older trucks with composite manifolds but nothing for this one. It looks like a part of the bottom of the manifold is plastic but the entire top and where it is leaking is all aluminum.
It seems odd that this would start in the winter time just driving back and forth to work (no load). And, yes the antifreeze is good. Just wondering if this is a known issue with this truck. Is it just a matter of replacing the gaskets or is there some other flaw I should be concerned about?
About, one month ago my car shut off while driving(pretty scary at the time). I pulled of the road and attempted to start it again. Everything looked good there, but as I was making my way home from work it started to act funny. It would not acknowledge me depressing the accelerator. When I got home, I ate supper, then went to have a look.
The car would turn on, but not acknowledge me pressing the accelerator at all, It did however go up to 30 mph at a snails pace as if it was coasting down a hill. I plugged in my code reader, and it read that the Throttle Body Valve was stuck open. I took it off and tore into to it a bit. I noticed the gears inside the TB itself were corroded and the butterfly valve was locked up.
I replaced the part, and tried to turn my car on with the new TB. All the dash lights are in working order, however upon turning the ignition to crank the engine, the whole car system shuts down. No lights no nothing, besides the car door open sound. The car will remain like this regardless of the key position until I have reset the batter(take off the terminals and put them back on) to which the process repeats itself.
The code reader says no codes are stored because I obviously reset the battery. So now am at a standstill.I believe the old TB froze up, because I had to run in through 3 ft standing water during a storm, and then deployed shortly after(I'm in the service) for a few months while letting the car sit.
I had a code for the EGR valve stuck open. I tried cleaning it but it didn't work (and didn't seem that dirty). Then I tried replacing it. Both times the code came back. What should I do now? I reset the code each time by disconnecting the battery.
View 14 Replies