Dakota :: 1996 V8 - Stuck In First Gear / Won't Shift
Jul 10, 2011
1996 dakota v8 automatic 4x4. tranny rebuilt 3 years ago got stuck in the mud and every since then it is stuck in first. wont shift no matter what i tried to adjust the tv cable and it didn't work at all. don't know much about dodge transmissions iv always worked on 4l60e in chevys. I don't know were to start. Where to start. iv been reading about the governor valve and shift selnoids are there any way to test any of this? first pulls strong and reverse works
View 1 Replies
Advertisement
My 2003 Dodge Dakota does not shift properly sometimes going into second gear and it only happens in second gear. I have to lift my foot off the accelerator for it to shift into third. If I don't it just screams at a high RPM and sounds as if it is about to blow. It has a hard time making it up a small incline such as an off ramp. Truck will not shift properly when going up grade. Engine will rev at 4500-5000 rpm but will not shift until I slightly release the gas pedal. Truck will also perform multiple hard up shifts whether in cruise control or not in cruise control, going upgrade. Took the truck to the dealer reprogrammed the computer with a "flash update" that was no luck. Not once has the ENGINE LIGHT ever come on.
So a lot of the comments that were presented to me I have done. Here is a list:
Changed govner senors and solenoid. Did not work.
Checked for exhaust leaks and other leaks. No leaks.
Checked all vaccuums. No problems there.
Had engine checked and dyno tested. No problems there.
Had transmission rebuilt. Same problem. (dealer did work)
Had new transmission put in. Same problem. (dealer did work)
Also, sometimes when I put the truck in reverse, it seems to about to stall, but it doesn't. It also does it sometimes when I put the truck in drive it seems that it wants to stall.
I just recently learned that my truck has a Transmission computer module, Transfer case computer module and of course the main computer. Is there a way to test those modules out?
View 3 Replies
This morning my 2006 Dodge Dakota v8 auto decided to become a large paperweight. I started it up fine and let it warm up a bit (about five-ten minutes), then shifted into reverse to leave my driveway and it won't move. It just rev's and rev's like it's in neutral. I tried Reverse, Drive, and both low gears, but no luck.
Since it got very cold, it has been making a buzzing/whirring sound that seems to be coming from the belts. But that sounds would go away when the car warmed up. I thought I needed a new power steering belt (and still may), but that wouldn't keep the car from moving at all, right?
View 19 Replies
I have a 1996 Silverado and it will not shift out of first gear. I have had the pickup for about 6 months and when I got it, it would shift if I accelerated to about 30 and let off but then I went though some mud and got stuck, I kept shifting from reverse to forward and I got out of the mud and it would not come out of first but reverse works fine and it will not shift manually at all the pickup has a 4l60e transmission.
View 5 Replies
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 Replies
On my 96' F-250 4x4, The tranny will shift to 3rd gear and that's it. If I put it in Neutral and then back into drive it will stay in 4th gear for about 15 seconds then go back to 3rd. What could be causing that?
View 14 Replies
I posted earlier this month about my 1996 Ford F150 4x4 manual tranny truck. It had gotten stuck in fourth gear, and I, along with others, assumed it was the shift forks. I cracked open the top of the transmission yesterday, and what do I see? Melted plastic staring back at me. What's going on here? There was melted plastic jammed between fourth gear and the inner wall.
Is this a case of the surgeon leaving his instruments inside the patient? Could a mechanic have dropped his tuna sandwich wrapper in the transmission at some time?
View 8 Replies
This is a car i am working on. 01 4motion passat. automatic. Tree fell on it. We put a new roof, quarter, door seats. Last night we moved it outside to clean the shop and went to move it back in. Won't shift out of park. Next tried turning ignition on the backing it off a little and cant get to neutral. Check fuses.
Brake light switch has been previously replaced by someone. and it works. Light next to gear selector working. brake lights fine. I have taken the center console out as much as I can. I can't get it completely out. But everything in there seems ok. When I press the brake in I don't hear any click or anything near the selector.
View 2 Replies
I read a couple posts on Gear Shift switching back to neutral. Here is my situation. Got in the car to return some movies and realized I left them on the table. Went back to the house, and right before I turned into the driveway, noticed a metal coffee cup had come out of the holder and the edge was up under the accelerator. I had been applying my brakes to slow for the turn into the driveway, then when I went to accelerate, nothing, then noticed the cup.
Removed the cup and stepped on the gas to go into the driveway. Nothing. Turned the car off, then back on and tried to put into drive, goes a tiny bit then slips back into neutral. Tried it in reverse, same thing, pops back into neutral.
I can hold the shift lever in position and the car moves. It's in the driveway now and will get towed to the Toyota dealer tomorrow. Obviously a problem with the shifter as a result of the "coffee cup" under the edge of the accelerator. And yes, I know it's dangerous, hubby used the car last on his visit home this weekend and apparently the coffee cup either got put down on the floorboard or was knocked out. I bring it in the home when I'm done.....anyway.
So, the most likely cause was the spring talked about in other posts breaking, or a switch sticking or what. Seems like something got knocked or shifted out of adjustment. Does the accelerator have some type of cut off switch if something gets lodged under it?
View 11 Replies
How to fix a gear shift that tends to get stuck once in awhile. What about WD, and how would you apply it? I have a '97 Monte Carlo.
View 2 Replies
I have 2011 Elantra at ~20,000 mile, and strange things started happening since last year...and it kinda blew up today.
My dashboard has been flickering randomly for a while, as in everything goes dark and turns up again in the middle of driving.
And today it turned off and turned on (as it usually does), and the dashboard seemed broken; speedometer stuck at 0 mph, rpm meter stuck at 0, all warning lights turned on, gas meter going up and down and stuff.
Fortunately enough I was close to home so I drove it back home, and my gear shift was stuck at neutral (I could switch b/w N and D).
So I took out the shift lock release? thing and managed to put the gear to P and pull my key out. I stepped out of my car and I smelled something burning...not a very good sign. What should I do? Well I think I need to take it to dealership tomorrow but I'm not sure if it'll be safe to drive...
View 4 Replies
My 2001 Santa Fe 2,4l - Have suddenly lost the abillity to shift gear. Its stuck in 2 and the shift stick is very loose in the "front to back and back to front" motion.. in other words there are resistance sideways.
I suspect it to be a broken shift cable. So my question is : changing shift cable on a santa fe easy? Is the best approach to start from inside the vehicle or from transmission side?
View 6 Replies
I was pulling into my driveway. I put the car in park, but when i went to get out of the car, it started to roll forward. When I finally got it stopped, I tried to shift it, and it wouldn't shift to any spot. Then it became stuck in between Park and Reverse. I can't move the gear shift.
View 1 Replies
I have a '97 F150 Lariat Ext cab, 5.4, 2Wd, 175K, a bit rusty but for the most part functional. Unit is parked for long periods of time.
3 - 4 years back the gear shift did not want to go into PARK and and the gear indicator was out of register. Unit would not start and I had to move shift lever to N to start. Fixed the two screws on shift plate/column per this site. Then 18 months ago same thing begin to occur but this time I used blue thread lock to hold screws in place. Still had to throw into park to get it to stay.
6 months ago shifter became very difficult to move and near impossible to get into PARK. When in PARK the interlock must have not been engaged so had to move to N or push lever hard into PARK to start.
Tired of this so I cruised the site and found several posts on taking dash apart, repairing a broken shift tube and or replacing bushings.
Battery disconnected, dash apart, cluster out, steering wheel still on and steering column still in position. Shift tube appears OK, i.e. not broken as in one post, bushings appears OK as there is no play or slop evident, but I cannot get the shift lever to move from PARK, period.
When the shift lever is pulled toward the wheel, a pawl on the tube causes a plastic or nylon arm to move about 90 degrees. It must be a stop or safety of some sort. I have not dug deep enough to see the shift plate with the two screws. At 75 I find it difficult to lay upside down to reach and hope I can get to them from the top.
Questions:
1. How do I get it out of PARK to check all things on shift tube and gear selector units?
2. Does the battery need to be connected for the interlocks to function?
3. Do I need to drop the column to check on shift tube items?
4. With a rusty trans, can the shift cable to trans connection be the problem?
5. What to look for, how to repair. etc.
View 7 Replies
I don't know what is causing this but I bought a 2012 elantra last week (500 miles on it so far). Yesterday when I went to start my car the clicker wasn't opening or locking the doors so I had to use my key to open the door. When I got in my car would start but was "stuck" in park and I couldn't shift past park (yes I had my foot on the brake). After about 10 minutes it just randomly worked... Today I was driving to work stopped to get gas and as I was stopping I realized I couldn't shift passed neutral to put in park (I could go back and forth between drive and neutral). While this was going on my windows would not go up or down. Again after 10 minutes the problem seemed to fix itself. What could be causing this?
View 12 Replies
I have a 2004 Hyundai Santa Fe, has 99,000 miles 3.5L. After changing the alternator (alternator did die and drained my battery, the shop recharged the battery) now it seems be stuck in 3rd gear and does not wont to shift (it is a automatic). Fluids are good, transmission was flushed between 50-60,000 miles.
View 3 Replies
I bought the car with 117k and never since my possession bothered to service it. Why? I kept putting it off well at 165k I said heck ill do it. Currently at 170k my gear wont shift past third and its reoccurring almost daily. When I first bought it it was intermittent. I think the late service messed it up. Here's the thing, aamco will open up my pan and look at my solenoids which is 250ish.
View 14 Replies
Volvo Automatic 1992 240 - So, just started to back out of the garage and, all of a sudden, my gear shift got stuck in neutral and then started shifting without engaging the transmission at all. Pushed it back into the space and, taking a look underneath, I realize the control rod's completely detached from the lever in the transmission.
I can re-attach it, but it just comes loose again when I shift. It seems like something should be in there to hold the control rod in place with the transmission lever, but I don't know what because I can't seem to find any documentation on what everything should look like down there.
Attaching a couple shots, one with a circle around the area that's coming un-attached since the angle's a bit off.
Attached File(s)
IMG_8972.jpg ( 1.09MB )
IMG_8978.jpg ( 938.64K )
View 1 Replies
My 1990 Honda Accord is stuck in "sport", and won't shift past second gear. The button isn't stuck, but the "S" light stays on.
View 3 Replies
This is what’s wrong with my 1998 Honda CR-V manual transmission. When it’s off, the gear stick works normally. However, when I start the car, the gear stick gets stuck and won’t move to change gears. It happened before a couple times and if I warmed the car up for about 10 minutes it worked normally again, and normally the next time I drove it. However, this morning, the gear shift would not work even after warming it up, except when the car was turned off.
View 5 Replies
My truck gear shift is stuck in Park (console type). I have been reading threads that discuss potential causes such as blown fuses, bad brake switch, bad brake shift interlock actuator, and even ignition switch. All fuses are okay. Before I try to get into all the other possibilities, I have a question around what the local auto parts worker suggested. He said that there is a small plastic piece that may have slipped down interfering with gear movement. This could make sense, especially since the white manual release lever doesn't seem to be moving.
View 14 Replies
