So my girlfriend got this car (2013 corolla s) a few months ago and we started hearing a funny noise, I thought it was a wheel bearing going but nope its the ouput bearing on the tranny, passenger side. is this common on corrollas? how hard is it to change? I have a tranny from an 06 corolla, are they the same? and could i just swap trannies if changing the bearing is too difficult?
View 2 RepliesI have a 2001 Toyota echo 2001 210.200 km and my output shaft bearing makes noise and I cant know the level of my transmission fluid bcoz I don't have dipstick and i bought trans 75w90 oil os that ok and how can I add this?
View 1 RepliesOn a 2ZR-FE 1.8L what keeps the cam bearing shells from spinning? This would be the shells closest to the cam chain, sprockets etc.
Are there the little tabs that are bent out at the end of the shell like a rod bearing, or are they locked into position as the cam cap is tightened?
My throw out bearing makes a faint chirping noise since I bought the car, but now that the weather has been in teens, it seems to be louder.
I was wondering if it is possible to grease the throw out bearing or something without dropping the transmission.
Title should say Throw-out bearing aka Release bearing.
I have a 2010 5 speed Corolla CE. Having problems with their Throw-out bearings. At around 8000 miles the sqeaking/chirping noise of the bearing was too much so I brought in it to the dealer to fix. They agreed and made the repair.
Now it is only at 10000 miles (22000km) and I can hear it starting again. Just wondering if it is a common problem?
Noise comes and goes as the clutch pedal is released. If you push it in it will go away. It also will happen in all gears but easiest to hear in neutral.
My 09 matrix is using about 3 quarts of oil every 5000 miles. I bought the car new and it has 114,000 miles on it. I don't notice any smoke or leaks anywhere.
View 14 RepliesDon't the stock brake pads go for more than 12k miles? The brakes are squeaking when I first pull out of my driveway and after a while it goes away, but at lower speeds (stop and go traffic) they still squeal a little bit, but when I am braking at higher speeds I don't hear anything. about a year ago my friend drove my car with the E-Brake up for about a mile. Could it be that because my rear drums are worn that my front brakes are getting worked more? But when I pull my E-brake up it still works fine without going up too much.
View 7 RepliesMy '09 Corolla (1.8L) still burns about a quart of oil per 2000 miles. This is after the reflash as well.. I am using 5w-20 synthetic at the moment.
View 14 Replies2010 LE is having a brake squealing issue. The car only has 35,000 miles and the pads are at about 50% life left. I cleaned everything and lubed everything and they are still squealing. I would hate to have to replace the front brakes this early especially when the pads are only half worn. They are the factory pads and rotors btw.
View 5 RepliesI got my 2011 S Corolla brand new and it's been great thus far. To make things a little more exciting, I got a manual. The last manual I had was my 2006 325i so it's been a little while.
Over the past few weeks, both my wife and I are experiencing quite a bit of clutch shudder or chatter and are finding it more and more difficult to engage the clutch without completely shaking the car. We've noticed this the longer the car is driven. On cold starts it doesn't happen. I've read some horror stories of the tranny going out, a weak transmission mount, or a warped flywheel in these Corollas. We bought this car because it's supposed to be reliable and get good mileage. Also, I'm still under the powertrain warranty but I'm not sure if they'll cover the clutch.
I have not checked the transmission fluid yet either. I can really use some suggestions. I had a 318is for over 100,000 miles and never put a new clutch in it!!! I'm getting frustrated.
I have a 2010 corolla le with approx 54k miles. Should I have the trans serviced/flushed? Can I just do a drain and refill? Is it true that replacing the fluid will cause the trans to fail later on?
View 1 RepliesMy mechanic just informed me that because of my extreme drop, the drive shafts are at an angle that is stressing the final drive bearing on the transmission. I am leaking very small amount of fluid, he said it might not be a big deal.
View 3 RepliesI installed a JDM 2ZZ-GE engine and 6 speed manual trans-axle into my 2000 Celica GT.
I have ran into a interesting problem. I replaced the output shaft seals and now whenever the car is in the air and the suspension is unloaded (the drive axle is pulled slightly from the trans) the drivers side seal leaks a bit of gear oil. The drive axle is snapped into place. Nothing leaks when the car is on the ground.
I did reuse the old drive axles, which had a lot of miles on them but still appeared good and useable. I have been told to replace the new seal because it may be damaged, but I am wondering if it may be that the drive axle end is worn.
I have seen this with harmonic balancers for engines. They even sell a replacement sleeve for harmonic balancers so you can re-use the old worn one.
Can I take off the output flange on the tranny and use a slip joint, with out changing the tail shaft?
View 1 RepliesMy front diff appears to be leaking from the drive shaft output. it's not enough to leave drips but the skid plates are oily. Having the dealer look next week. 60k on a 2011 460.
View 3 RepliesI replaced the seal the other day on my ranger because I noticed my fluid disappearing. Went ahead and changed the filter and fluid as well. Flushed the system, and I go back to my truck tonight and there's a huge puddle of trans fluid. And the output shaft seal is once again, up against the drive shaft. I've spent like $150 on trans fluid since Friday, and $1000+ to get the truck running again last month, so pardon me if I get edgy about her.
99 2.5 auto. I changed the trans pan gasket too. No leaks from it.
Okay, I have a P0720 code. I bought the Output Shaft Speed Sensor and read that it is on the back end of the transmission.
Need to confirm that it is on top of the transmission, near the tail end? Why are parts that go bad always in the most inconvenient places?
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesI removed my drift shaft to get balanced since I have felt a vibration at 55-60 mph. After removing the driveshaft I noticed there is some play in the output shaft when I grab a hold of the yoke on the transmission. The play is a slightly up and down. If my memory serves me right that should not be. Seal is not leaking but need diagram of this yoke off the output shaft. I know in past on other vehicles there is sometimes a crush washer. Also what is the torque specification for that output shaft nut?
View 3 RepliesI'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 RepliesI just replaced my starter and on my first ride after replacing it the X started to stumble a bit, and then would stall out at almost every stop light. It threw a CE light and I pulled the code P0720. I searched here and it seems most guys say this is a C.O.P. issue. If it is a bad C.O.P. would it stall like that?
I did have the battery disconnected but I made sure the terminals were clean and tight. Is this a coincidence or did I do something while changing the starter?