Corolla / Matrix 2009-13 :: OBD2 Error / P0304 Code / Cylinder 4 Misfiring
Jan 23, 2013
Went on a trip Sunday, and i saw my engine light come on after i put gas in the car. I pulled over, re-checked the gas cap, and it was fine. Car felt fine.
When i got home, i used my OBD2 scanner, and got the error P0304 Code - Cylinder #4 Misfire. I cleared the error and drove the car some more, no issues.
Yesterday, my wife took the car and she said it was hesitating and sputtering, but the light hasn't come back. I have an appointment at the dealer tomorrow, the car has under 80,000k, so the warranty should kick in.
View 2 Replies
Advertisement
Check engine light came on. Codes are P0300, P0302, P0304. Plugs were previously changed. Plugs look good. Changed both coils. Light still one. Injectors also previously cleaned. What else should we check for? Valves hanging? Anything else to check for?
View 5 Replies
My daughters '09 Corolla was shaking and misfiring occasionally. When she took it to the shop the mechanic had it for a couple days and after many attempts finally reproduced the issue. After several diagnostics tests they determined it to be a damaged cylinder. We had the option of
1. replacing the engine
2. retooling it
I called around to a couple other mechanics and they told me the same thing. One particular mechanic (no affiliated with Toyota) told us that he had heard this happening on both the Camry and the Corolla. Sound like a manufacturer issues if it's been seen frequently.
View 5 Replies
I left my chevy s-10 truck sitting over the christmas (23/24/25) and it was really cold outside and when i got back i started getting a P0304 (Cylinder 4 Misfire). I replaced the spark plugs and spark plug wires. May be the cold would cause this to happen? I think I've noticed the trucks fuels efficiency drop over the past month). May be the fuel injector(s)? Is the s-10 TBI or does it have fuel injectors for each cylinder?
View 8 Replies
I have the code P0500 on my 2009 Matrix. The odometer doesn't function, all error lights are on, the power steering is not completely out but it's reduced. Also, the rear windshield wiper is constantly on. I replaced the vehicle transmission sensor today because I thought that would fix it all. It had absolutely no effect.
View 5 Replies
2006 PT Cruiser Touring Ed. The engine light came on 2 days ago, had it looked at today and the error code p0304 "cylinder number four misfire" was diagnosed. What causes that and what would need to be done to fix that problem?
View 9 Replies
1997 Ford Mustang 4.6L EFI engine with 67K miles. The engine is actually now in a Factory Five Roadster. It sat on a stand for 5 years but runs well now with the exception of the code. I keep getting a code P0304 (cylinder 4 misfire) and I've checked the plug - the code seems accurate; it is misfiring.
Things I've tried:
1)swapped plugs,
2)this is a dual coil engine so I've swapped coils,
3)the #4 plug is the longest sparkplug wire so I've gotten high-performance wires,
4)heavily grounded the AL head,
5)put dielectric grease on the plug,
Still, ONLY cylinder 4 gives the misfire.
View 7 Replies
I am far from home. Taking a road trip. Day 2 out of 6. My check engine light came on, so I just pulled over. All fluids were fine. Found some place to read the code:
P2757 TCC pressure control Sol Ckt Perf / Stuck off
The guy said it was something to do with trans.
View 3 Replies
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
View 2 Replies
I have a 2009 Corolla S 1.8 with a manual transmission and 30,000 miles. About a month ago the check engine light came on throwing a PO302 code (cylinder 2 misfire detected). I reset the check engine light and drove it about a week before the check engine light reappeared again with the PO302 code. I swapped the spark plugs on cylinders 2 and 3 and reset the check engine light, the PO302 soon reappeared. I swapped the coils on cylinders 2 and 4, and reset the check engine light, the PO302 soon reappeared. I swapped the fuel injectors on cylinders 2 and 3, and reset the check engine light, the PO302 soon reappeared.
View 1 Replies
The issue with 99 Corolla CE with 147,000 miles....
I have a misfiring P0303 Code - Cylinder #3 Misfire. Here is what has been done in an effort to remedy the misfire. A major tune up, new spark plugs, new fuel injectors, new spark plug wiring, new coil packs, The car runs ok once warmed up but in the morning the engine vibrates until warm and also shivers a little while the car is stopped at a stop light. I have dropped it off at the mechanics a couple of times now to no avail. Once the code is reset it will not display the CEL for a couple of days but the symptoms still remains. The CEL comes back on within 2-3 days with the same code. Really frustrating! Well, at least this time CEL in not flashing like before it comes on and stays on.
View 1 Replies
My girlfriend drives an 09 corolla (1.8L I believe). I have an OBDII bluetooth reader w/ Torque App so to identify the issue I can get some data:
Last week I was driving the corolla and I got P0031: HO2S Heater Control Circuit Low (Bank 1 Sensor 1). Car seemed to run fine without any issues. My girlfriend brought her car in to her "mechanic". "mechanic" who will replace have of your engine only to realize that your gas cap was cracked. He apparently replaced 02 Bank 1 Sensor 2 (I'm still trying to confirm this and to get the part # to make sure). He reset the ECU and she drove for about 30 miles after which these codes popped up:
P0172: System too Rich (Bank 1)
P0101: Mass or Volume Air Flow Circuit Range/Performance Problem
The car was idling rough. I reset the codes and the car was running fine until all monitor systems were ready. When Catalyst, 02 Heater & 02 Sensor are not ready everything is running fine and I don't see any error codes. I cleared ECU a few times. The last time I was able to drive for over 20 miles without any issues. Currently the only sensor not ready is 02 and car is running fine but I have a feeling once its ready the car will start having issues again:
Summary (if you don't want to read everything)
*P0031: H02S Heater Control Circuit Low (Bank 1 Sensor 1) - Car runs fine
*Mechanic replaces 02 Bank 1 Sensor 2 (Trying to find part # and double check sensor name)
*ECU reset and car runs fine for 30 miles
*P0172: System too Rich (Bank 1) and P0101: Mass or Volume Air Flow Circuit Range/Performance Problem
*ECU reset - car sputters and hesitates
*When all monitors are ready same codes (P0172 & P0101)
View 2 Replies
My car was shaking badly during idle and the Engine and VSC Off lights came on simultaneously. I took it to a local garage (not dealership) and they said that there is anti-freeze leaking into a cylinder. They said the only way to clean it out/fix it is to first remove the entire engine from the car so it could be worked on. It will cost a total of $2,700. My engine has 141,000 miles on it so they said this may be risky since it is so used. They said for $3,500 they could swap it with an engine that only has 31,000 miles on it (and a 6 month guarantee.) By numbers this sounds like a no brainer (I am assuming?) but I am curious if swapping the engines would be worth it seeing as the rest of the car has still traveled 141,000 miles. I have kept it in good condition and such though. I am also curious if the engine really does need to be removed to fix this sort of problem or it it could be done cheaper.
View 4 Replies
An OBD tester is reporting error code P1100. Checking online I have discovered that it is in reference to a Barometric sensor that is reading out of range. However, I cannot find any identification of the Toyota part number, its location, and whether or not it is a DIY replacement
View 1 Replies
My Corolla has the P0441 code, but not the typical 0445 code that comes with a loose gas cap. I cleared it and it came back (yes, I checked the gas cap). Googling the issue, I found service bulletin SB 0392-08, which implies the ECM could need to be replaced if the issue is not in the Evap system.
View 1 Replies
I have a 2009 corolla LE with 81,000 miles on it. Today after I got gas, the check engine light came on. I checked the OBD code and it said P0607. I cleared the code and continued to drive it and it ran fine and the light has not came back on yet. I'm a little worried about driving it on long trips now.
View 2 Replies
Have '01 SE. yesterday I got a misfire in cylinder 4 (code P0304) the service light blinked on and off 3 to 4 times than stayed solid. changed plugs and boots about 1 to 2 months ago, didn't change coils and they r not in the best shape but didn't have money to replace at time. So I replaced the coil for #4 and it still runs rough with code, plug has some ware but looks fine.
View 1 Replies
2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 Replies
Well, I have a big problem on prius 3, the problem is that it has a big and I mean a big body shake when I decelerate above 30 mph or slowly accelerate above 30 to 50-70 mph, when I fully accelerate, the body shake disappears. When the body shake occurs MIL comes blinking and DTC P0304 comes but not always, but the shake is only when the coolant is hot.
On the other hand, if the MIL is not on with the tester it can be seen that the cylinder 4 has misfire margin, only cylinder 4, every time. Now what I have done is to exchange the injectors, problem remains on cyl4.
-replaced the coils, problem remains on cyl4,
-clean the EGR, problem remains on cyl4,
-opened the engine to see the valves, cylinders, pistons, exchanged the ring set,problem remains on cyl 4,
Replaced the wheels, the problem is still there, now I want to replace the drive shafts.
View 19 Replies
I have a 2009 Corolla with a 1.8 L. I have the misfire code P0301. I have changed the plugs, ignition coil, and fuel injector on cylinder one. It still has the misfire.
View 5 Replies
I know I can fix this problem, but my question is which cylinder is #4? I don't see it marked on the engine. The counter guys at both my local parts supply stores (whose initials are A and O) can't even look it up for me. If #4 is on the front of the engine, then it's an easy fix. If it's on the backside, then the intake manifold has to come off to get to the plugs and coil packs. It's a bit more labor. I can do it, but I'd rather not have to.
View 1 Replies
