Corolla / Matrix 2009-13 :: Clutch Creaks Like Old School Bus When Engage And Disengage
Mar 19, 2013
I think this is just poor dealer service, but I need a sanity check.
I have 93k miles on my Corolla. My clutch creaks like an old school bus when I engage and disengage. It's done this pretty much all along and I think I had another dealer successfully lube the linkage to quiet it down -- it was miles and years ago so I may be misremembering that.
My current dealer says all they can do for it now is REPLACE THE WHOLE FREAKING CLUTCH assembly to the tune of $1,300. Clearly, I'm not doing this. As long as it works, I ain't replacin' the clutch, but, REALLY?
View 1 Replies
Advertisement
Have a click when the clutch engages? Manual transmission.
Everytime is release the clutch, I hear the clutch click when it grabs. It's not the pedal that clicks. It's inside the transmission.
It runs fine, and it's been doing it right off the lot. It's not that loud to actually bother me, I'm just wondering if its normal.
View 5 Replies
I have 2009 corolla with about 125, 000 on it. A few times over the past couple of weeks on chilly mornings (in the 50's) the transmission did not engage in reverse right away. Usually with the fast idle you can feel it kick in but on these days it takes a few seconds before that happens. I have had the car for two years and have done nothing about transmission service. A dealer told me it was lifetime fluid and there is no dip stick to check it. Is this a common problem? Is this a sign the trans is on the way out? Should I sell the car now before it gets worse?
View 3 Replies
Is this normal? You can hear the air coming out.
The reason I ask if it's normal is because it seems like I have to press my brake pedal halfway down before it engages. At least an inch or two. However I can still lock up the beaks. But it seems like they are not as sensitive. Takes a bit of travel to engage.
I've already bled the brakes too.
View 1 Replies
The A/C in my truck stopped working last year, and this year I intend to fix it. I believe the problem is with the compressor clutch because it was making noise as it would engage or disengage. It was making this noise for a good year or so, and then one day the noise stopped and I have no A/C. So I am only assuming its the clutch.
View 4 Replies
I have a 2011 corolla XRS 5 speed with about 32,000 km's. There is a squeak when i press the clutch down coming from outside the car. I brought in my car for scheduled maintenance and they initially said that the clutch fork would be to be lubricated. I got the car back, thinking all had been taken care of, but noticed next day that it was still squeaking. I went back there for them to tell me. 'oh yeah, we can't lubricate unless we pull off your tranny.' I would have to leave the car there all day and so forth and so forth.
I thought it would have been a simple solution but i am concerned now about them pulling off the tranny and therefore maybe causing some other issues now or later.
I don't hear the squeak when driving usually only when stopped with window open and pressing the clutch.
View 2 Replies
I went driving today and for a moment I could engage/disengage the clutch pedal with little to no effort. It goes back to the normal force after 3-4 shifts.
It's the exact opposite of what's happening in this thread. [URL] ....
View 11 Replies
I got my 2011 S Corolla brand new and it's been great thus far. To make things a little more exciting, I got a manual. The last manual I had was my 2006 325i so it's been a little while.
Over the past few weeks, both my wife and I are experiencing quite a bit of clutch shudder or chatter and are finding it more and more difficult to engage the clutch without completely shaking the car. We've noticed this the longer the car is driven. On cold starts it doesn't happen. I've read some horror stories of the tranny going out, a weak transmission mount, or a warped flywheel in these Corollas. We bought this car because it's supposed to be reliable and get good mileage. Also, I'm still under the powertrain warranty but I'm not sure if they'll cover the clutch.
I have not checked the transmission fluid yet either. I can really use some suggestions. I had a 318is for over 100,000 miles and never put a new clutch in it!!! I'm getting frustrated.
View 2 Replies
It was about 7 degrees Fahrenheit and I started my car and it took a few seconds longer to start then normal but I kind of expected that as it was pretty cold.
Then after letting the engine warm up a little bit I went to leave and the clutch pedal was sticking for a second or two between shifts and I still kind of ignored it and drove home, well after a 45 minute drive by my house it was still doing it.
The next day I drove it to the store and after sitting in my garage for a while it was fine. A few days later, (well last night) I went on a break to get some food and it did the same thing when I left to do that but after it was warmed up to normal operating temperatures it was fine again. When I first started it, the temp was 13 degrees.
I am trying to figure out if there is something wrong with my car or if all of them do that. I am going to stop by the local dealership on my way home today but if it is normal I don't want to waste my time. I just don't like the fact that I live in Minnesota and the temperature is going to get colder then that. I mean what is it going to do then?
View 1 Replies
Title should say Throw-out bearing aka Release bearing.
I have a 2010 5 speed Corolla CE. Having problems with their Throw-out bearings. At around 8000 miles the sqeaking/chirping noise of the bearing was too much so I brought in it to the dealer to fix. They agreed and made the repair.
Now it is only at 10000 miles (22000km) and I can hear it starting again. Just wondering if it is a common problem?
Noise comes and goes as the clutch pedal is released. If you push it in it will go away. It also will happen in all gears but easiest to hear in neutral.
View 14 Replies
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 Replies
I have a 2011 Toyota Corolla S 5 speed manual and after 15000 miles I noticed a ticking noise in my engine bay and goes away once I push down on the clutch, but once I get off the clutch the noise comes back. Is this a normal thing or should I be concern? I have 75000 miles on my car now, is it covered through the extended manufacturer warranty coverage of 120000 miles?
View 4 Replies
I have a 2009 corolla ce i can get the key in to the ignition ...
View 1 Replies
So I want to disable the ABS on my Corolla. I was wondering if I could pull the fuse in my bonnet to disable the ABS and if I were to do so which fuse would I pull.
I think if I were to pull the fuse from the interior, the other car features that are tied into the fuse wouldn't work.
If I can't pull the fuse in the bonnet, what are the other ways I could disable ABS? I read that removing the relay is an option.
Also is there anything I should know if I were to reactivate ABS? For instance, would the ABS light be off when I presumably reactivate it or do I need to perform some extra steps to remove the ABS light?
View 12 Replies
My 09 corolla has a whine at around 35-50 mph it does sound like its rpm related. When i let off the throttle it isn't as loud.
[URL] ....
View 6 Replies
I was wondering would the 2.4 2az-fe fit in to my 1.8 corolla I want to get a bare block or blown engine and build it up and turbo it and then put it into my corolla. Would the 2.4 bolt up in place of the 1.8 and if so where I can get a bare block or a complete engine?
View 10 Replies
I have an 02' 2.0 Jetta Wagon, and the A/C is having some issues. Since I know close to nothing about A/C systems, I took it in to a few places to have it looked at. I've had the whole system Evac'd and recharged, and have had the low pressure fitting replaced (apparently there was a slight leak there), and the system is still not working.
The A/C worked fine when I first purchased the car a few months ago. Shortly after my 800 mile trek from Oregon, back to home, the A/C started to only work intermittently. The compressor would engage, then disengage, repeat...It seemed like a bad idea to keep trying to use it in its sad state so I stopped using it altogether. As I said, I had the system emptied and recharged, but it still only works intermittently. It sort of follows a pattern where upon start up it works longer, and switches on and off at shorter intervals, until it doesn't engage at all.
There are no strange noises from the compressor, and when it was hooked up to the machine, it proved to be performing its function well.
View 5 Replies
owner of a 2007 Passat 2.0T wagon, 6 spd manual, 32k km's. (leased) I'm having repeated persistent parking brake failures (won't engage, or won't disengage).
-About two months ago the parking brake would not disengage, error message on the MFD, yellow warning light and warning tone. Called roadside, finally got it disengaged by removing one terminal from the battery. Took it straight to the dealership, they "fixed" it by resetting the computer.
- The next day I have auto hold engaged, parking brake did not disengage when I turned the car back on. Had to turn engine on/off several times before it disengaged.
- Took it to the dealership again, had to get a rental car over a weekend while they diagnosed the problem. This time they changed some wiring and replaced the parking brake button.
- Next day the parking brake engaged ok but wouldn't disengage. Same routine on/off/on/off to get it to disengage.
- Back to the dealership again, they decided to replace the brake control module but didnt have stock.
- Last week I took the car back in (4th trip for this issue), they replaced the module and said it was fixed. Next day my wife got stuck in a parking lot with the parking brake stuck on.
- Called the dealership last friday and asked them to come pick it up this time, as my wife and I are sick of the inconvenience of this issue. (we share the car, both work, and also have a child's daycare to schedule around)
The problem is intermittent but not difficult to cause a fault. Can be caused when engaging, disengaging, or when the PB kicks in from auto hold when turning the car off. I try not to use it, but sometimes is necessary (parking on hills etc).
The dealership doesnt seem to know the problem and are just throwing parts at it. What recourse do I have for repeated problems? The manual recommends using this parking brake EVERY time the car is parked, so I don't think it's too much to ask to have it working properly.
View 24 Replies
I recently bought a 1997 f150 4x4 with shift on the fly. I bought the truck from an old man who parked it outside his house. I love the truck, but the 4x4 has been finiky. I have done a ton of research and i have done a bunch of testing. The vacuum system is working correctly. I have tested the solenoids and the front axle actuator is working properly.
There is some kind of electrical issue. It might be the GEM (i really hope not), but it might be the shift on fly switch itself.
The 4x4 will engage, but when i turn the switch to 2h nothing seems to happen. Driving in reverse doesn't work. But sometimes it switch from 4h to 2h, just by turning the truck off and restarting it. If restarting doesn't work, then i have to pull the 5 fuse, let it sit, then put it back in. I read that this resets the GEM. (Number 5 fuse, middle row, 5th from the top).
Resetting the GEM usually does it, but not all the time. Sometimes it will still be in 4x4 again after resetting the gem. And then what is really weird, after driving it in 2h (after the gem reset) then turned it off and restarting it, it will go back into 4x4. All this happens with the switch set to 2h. So I have been having to reset the GEM, each time i restart it. (This was going on for a day or so.)
Any easy testing i can do? Do you think it could be the switch on the dash, or more likely to be the gem? I hope it isn't the gem. I don't want to have to pull a fuse each time to drive my truck.
View 2 Replies
09 le 1.8 135k miles. Had serpentine belt break while driving home, pulled over, had car pulled in on a trailer. Pulled old belt and found water pump was bad along with belt broken. replaced both, car would fire off as should, but would still run hot while leaving parked running. pulled thermostat, found it would not open until about 15 degrees above opening temp. replaced thermostat, now car will turn but won't start.
Disconnected battery to try and clear any codes that would prevent it from starting, still won't start. have had to charge battery a couple times so wondering if it's the battery not having enough charge to start car up? i wouldn't think so, and it doesn't make sense for it to be plugs since it was starting up without a problem before changing thermostat.
View 2 Replies
The air coming out when the on the drivers side is significantly warmer than the air coming out on the passenger side when the A/C is cranked to four. At times it is borderline hot unless I kick back the setting to a two or three and then the sides even out a bit more, but it still seems like the right side of the car is much cooler.
View 9 Replies
