Corolla :: 1999 - Fixing Misfiring Code P0303 On Cylinder 3?
Sep 6, 2014
The issue with 99 Corolla CE with 147,000 miles....
I have a misfiring P0303 Code - Cylinder #3 Misfire. Here is what has been done in an effort to remedy the misfire. A major tune up, new spark plugs, new fuel injectors, new spark plug wiring, new coil packs, The car runs ok once warmed up but in the morning the engine vibrates until warm and also shivers a little while the car is stopped at a stop light. I have dropped it off at the mechanics a couple of times now to no avail. Once the code is reset it will not display the CEL for a couple of days but the symptoms still remains. The CEL comes back on within 2-3 days with the same code. Really frustrating! Well, at least this time CEL in not flashing like before it comes on and stays on.
View 1 Replies
Advertisement
2009 corolla 1.8l 155,000 miles. Replaced iridium spark plugs at 100,000
I got a CEL few weeks ago, P0301 Toyota - Cylinder 1 Misfire Detected
Car has been running bad for about 2 weeks now, excise noise on the highway, especially up hills.
Yesterday, I took a look, replaced the spark plug in cylinder 1, same results. Checked the coils using one of those flashing tools, all 4 flashed quickly, with no breaks in flashing. put it all back together, cleared the code, went home.
Took it out for a drive today, and it started running way worse. Checked the CEL, and now I have both P0301 and P0303 Misfire on cylinder 1 and 3. Barely made it home, ran VERY VERY bad.
Got home, and made a video of it. It just kept dying. Check it out here. [URL] .....
Also, when it does run, it almost sounds like I can hear excess air, its hard to hear in video, but doesn't sound right. Maybe air leak? How do I check?
View 2 Replies
Went on a trip Sunday, and i saw my engine light come on after i put gas in the car. I pulled over, re-checked the gas cap, and it was fine. Car felt fine.
When i got home, i used my OBD2 scanner, and got the error P0304 Code - Cylinder #4 Misfire. I cleared the error and drove the car some more, no issues.
Yesterday, my wife took the car and she said it was hesitating and sputtering, but the light hasn't come back. I have an appointment at the dealer tomorrow, the car has under 80,000k, so the warranty should kick in.
View 2 Replies
On my wife's '99 Explorer, she just acquired, we had a P0303, #3 cylinder misfire. I found the plug cracked and replaced it. Do the codes reset themselves or do I have to do it? I'd rather not disconnect the battery and reprogram the radio.
View 7 Replies
Still P0303 code after: New spark plugs, new spark plug wiring, new coils, new injectors, full tune up. 99 Corolla 147,000 miles. What else could it be? o2 senor? or maybe intake manifold leak? valve leak? what am I missing?
View 1 Replies
Went to do a few things this morning, started the car and it ran like crap. It was an obvious multi cylinder misfire. I checked to make sure all the coil connections and all other visible connectors were tight. Went back around and noticed the mil was flashing, so I shut it down and took the girl's car. I returned later in the afternoon and swapped out my intake in anticipation of it going to the dealer. Started up the car afterward and it ran fine without the mil lit. I had the codes pulled:
p0300 p0303 p0306 Its kind of weird that 2 coils would go at the same time. Do these cylinders share a coil or fuel injector driver off the ecm?
View 9 Replies
It keeps reading the code P0303 "cylinder 3 misfire". All coil packs, fuel injectors, spark plugs have been replaced. The exhuast smells normal. The oil is the correct color(maple syrup color, NOT milky). It's not blowing through coolant. Compression test came back normal. It's not the cat converter because the exhaust doesn't smell like rotten eggs. The car is sometimes hard to start. it hesitates/stumbles and shakes really bad. It feels like its not getting enough power.
View 10 Replies
I got a check engine light. I went to Auto zone to get it read & they came up with a P0303 - Cylinder 3 misfire. Since I bought the vehicle a couple of months ago, I don't know when the plugs were last changed, so I decided to change them. However . . .
Is there a secret to getting the plug boots & wires out of the hole and off the plug without wrecking the wires?
View 2 Replies
I have searched but with no solid answer..
What I got - 04 Camry, 231K, never had issues, do all my maintenance myself, brakes, plugs, oil etc..
#3 Cyl misfire..
Possible causes
Plugs, - Has been about 2 years since I replaced
Coil - Bought car new in 04, never replaced
Cat - never gave it a second thought
fuel injector - put techron by Chevron just about every oil change, I know I missed one here and there..
burned exhaust valve - say it aint so...
poor compression - I have to rent a tool...
defective computer - I don't think so..
View 14 Replies
So I have a 2004 Jetta gli 1.8turbo and my CEL came on last night from normal driving, after it came on it still drives the same. I had it scanned for codes and got the p0303 cylinder #3 misfire. wondering what could be the solution for this? I dont think its the coil pack because I had them changed at the dealer from the recall about 2 months ago (anyway to check?) Also I have 97,000 miles on my car and my last oil change I used 0w-40 oil. I know this is probably not the best oil to use at this mileage but I had an extra 5 quarts of them laying around so I decided to use it.
View 24 Replies
1997 chevy k1500 ... I have a misfire on cylinder 3 that i cannot figure out the cause. The idle is rough, backing out after starting is very rough, it seems to pick up at higher rpms but once the truck upshifrts to the next gear it shakes like a leaf in fall. within the past year the engine was rebuilt all new seals a new fuel pump, new injectors, new everything practically. so far i have done the following:
compression test results:125-130psi
fuel pressure test results: 50psi once primed, 50psi with engine running, no immediate pressure loss after engine is shut off
new spark plug wires
new spark plugs
replaced all four o2 sensors
View 19 Replies
So my 2001 5.3L truck has 206,648 miles on it. Over the years, it's been serviced every 5K with the only big repair being head gaskets which were done about a year ago.
Two weeks ago, I hit the gas to merge into traffic and the SES light started flashing and I could tell there was a miss. I got off the gas and a few moments later, the light went out and the miss was gone. I pulled the code and it was P0303 so I change the plugs, wires, and the coil pack for Cyl 3 fuel filter and ran a double dose of Sea Foam through the gas tank.
Bad news is I still have the problem. The truck drives fine; in fact, I pulled my bass boat 75 mile round trip yesterday. Everything is OK till you hit the gas hard to merge or to go up a big hill or pass someone. When you hit the gas hard, SES starts flashing and there is a miss. I also noticed the valves ping loudly when the SES is flashing. The only code it's giving me is P0303.
Could this be a bad injector not delivering enough fuel at higher RPM/under load? I was going to swap injectors and see if the miss moves. Any tips on popping those injectors out?
View 3 Replies
01 Taurus, 3.0 pushrod motor. Single 6 pack style coil. I replaced worn plugs 2 months ago for misfire. Car seemed to run fine. Now, I have misfire again. Code is for single cyl, 0303. Would u expect plug to foul, or bad wire, or possibly bad coil? I don't know how these ford coil packs fail. Can u lose 1 or more spark outputs with them?
View 11 Replies
I own a BMW not a VW! My 19yr old daughter purchased her first car a few months ago, an '03 Jetta 2.0L with approx. 170,xxx miles. Just after she got it we pulled a P0420 code, but it ran fine so we haven't worried too much about it. I've cleared that code and after about 2 weeks it will come back. Last week it started to have some issues with rough idle, stumbling/hesitation. I pulled the codes yesterday an in addition to the catalytic code is a cylinder #3 misfire P0303. I thinking the 2 codes are not related. I'm assuming the typical things to look for on the misfire are coil, wire, plug? Looks like the coil on this engine is a combined unit so no switching coil packs to see if the miss follows a bad coil pack.
View 4 Replies
We got our latest Santa Fe computer email and it warned of an engine fault. The car itself was not flashing any warnings though. Took it to the dealer and they said OBD was throwing a P0303 cylinder 3 misfire code. They shifted the ignition coil, and replaced the injector and seal before resetting the code. They had the car for 3 days though. Car was not running rough or anything else you would expect from this type of issue. Still trying to figure out why we got the email with no indication of trouble from the car itself.
View 3 Replies
2003 hyundai accentra and I have trouble code P0303 misfire detected cylinder 3 the car would run rough and hesitate at idle and run rough in drive and reverse I checked the plug gap on number 3 cylinder and it was excessive so I regapped it and put back and the car run good for about a day and now the engine light is back and is running rough and hesitating.
View 1 Replies
I recently bought my 2010 gti used with 62k miles on it about 3weeks ago. The car had an carbonio intake stage 1 and a stage 1 tune from Apr when I had bought it. On the test drive and for the first two weeks I had it I did not have any problems. A few days ago on a cold start my car threw an MIL and it was flashing. When I got to school I plugged it into the obd2 scanner. Code read P0303: misfire cylinder 3 detected.
My teacher and I went over possibilities of the misfire. Coil pack, plugs , injector, valve float( even tho this should not occur at 1300rpm cold start) we also thought that maybe because the car is direct injection the valve was not closing all the way due to carbon build up on the top of my valves which in this case I'm glad I don't have an interference head. I moved around the coil packs. What is the cause of this? I'm only misfiring at start and when the engine isn't warms up to operating temp.
View 5 Replies
Code: P0303 Misfire on cylinder #3.
Swapped coil from cylinder #3 to cylinder #6 and fuel injector from #3 to #2.
Shows misfire is still on #3. Plug looks normal tan brown.
#3 is the middle cylinder closest to the firewall I take it.
View 7 Replies
I own the 2014 Santa fe turbo 2.0 litre limited which has 4000 km on it. Within 210 km the engine light came on 3 times. I took it into the shop and they ran a code of P0303 which is a misfire, they changed the coils #2 and #3 and cleared the code. The second time it showed the same code but the shop said it was in the history so that is why the same code came up again. They ran an update ECM? and all was good. Now the 3rd time they tell me no code has come up and can't do anything about the engine (they cleared it) but it was like chasing ghosts. My vehicle runs great so not sure why I am constantly having this issue.
View 68 Replies
Got a 1996 Ford Ranger with the 4.0L in it that has a misfire on the #3 cylinder and giving check engine code: P303. Have tried new plugs, wires, distributor, switching out the coil pack with a known good, checked injectors for pulse, checked injectors, moved injectors and still the misfire remains on #3. Removed the valve covers and all appears to be well.
View 14 Replies
Brought home tonight a 2001 Ford Escape 3.0L 24 Valve V6. Bought it from a mechanic who's customer didn't want to put any more money into it. Has 185000 miles on it and it throwing the P0303 & P0171 codes. Cylinder 3 miss and Lean condition bank1.
Mechanic thinks it is a valve seat in the cylinder head next to the fire wall. Before I start replacing the cylinder heads with new remanufactured heads I plan on doing a compression test and leak down test.?
View 14 Replies
