I have 1988 Chrysler Lebaron. It dies after I first start it and now it is doing it any old time. If I tromp on the gas it sputters and keeps going. It is really bad at stop lights, stop signs or slowing down for corners. Also the ac is not cooling. The blower is fine, but no cool air coming from vents.
View 3 Replies92 lebarron conv. 4 cyld. non turbo
New cap, rotor, and plugs
Misses on 3 and 4.
When pull plug wires engine doesn't change. When pull 1 or 2 it dies. When put in gear it chugs and dies.
I had a remanufactured 2.5 Liter engine installed in my '88 Chrysler LeBaron Convertible. The engine vibrates and starts and dies in the AM until it warms up. I also had the engine and transmission mounts replaced; it made the vibration worse, I can really feel it in the steering wheel.The two balance shafts have not been checked, in addition to that, what else should I check for to resolve this problem?
View 7 RepliesThought this would be a fairly straight forward fix of making sure that the transmission fluid was full with no air in it, as well as a few other things to try.
Well, I've run out of things I can reliably try right now. Replaced the output sensor on the transmission, filled the transmission fluid with the proper type, read error outputs. (boy was that odd, you have to turn the key three times in a certain way and it blinks codes out at you)
The error readouts point to an Oxygen sensor, and the speed sensor. The oxygen sensor I could care less about at the moment, as I can't really reliably drive the car in first gear. Once it shifts, then I'll fix that, otherwise its wasted money as I won't be driving anyways.
None of my local mechanics have a machine to read or program this thing by the way, so that is kind of out of the question.
My son has a 1985 lebaron and the brakes just suddenly stopped working. He has replaced the pads, rotors, calipers and bled the system but when you push the brake pedal it goes to the floor. the mechanic where is works is stumped - been like this for three days and they can't figure out what the problem is.
View 6 RepliesI have a 1993 Chrysler Lebaron and the power steering on it just stopped working today. It was low on power steering fluid and I replaced the fluid but it still doesn't work. I can't find anything related on the Internet.
View 5 RepliesI have an 88 New Yorker whose digital amp gauge swings between its lowest and highest setting this makes the audio command center report electrical malfunction service immediately. Shortly after the car dies it will restart after 15 to 30 minutes. It doesn't throw any relevant codes, has had the alternator replaced still no luck.
View 8 RepliesI have a 1996 Chrysler LeBaron and when it idles it overheats so I did my research and I figured it could be the water pump I replace the water pump and during that process I had to disconnect the timing belt then put the water pump on and reinstall the timing belt when I put everything back together I thought I was done but it didn't start and I'm wondering if it's because the timing is off. I did not reset the timing nor move the camshaft how can I tell what's going on.
View 1 Replies1993 lebaron GTC... I just got the oil change, and the tec slip and the wrench touch the starter, positive and negative ends. I have power every where but no crank to start. I had a new backup starter and replace it figure that it was shot but after getting it tested its fine. I can hear the starter but i get no crank. Where do i look?
View 9 RepliesI have a 95 chrysler lebaron that stops accelerating while driving. I have had the fuel pump replaced twice in the last year and now it is acting up again! It jumps and then gives up. I have not noticed any other signs that happen.
View 2 RepliesI own a really nice original ' 89 Chrysler Lebaron coupe with the 2.5 N/A, throttle body injection and 3 speed automatic. It has just over 100k miles. The car sits in the garage all the time and is not used during the winter months and is never used in the salt season. I do "try" to start it sometimes just to keep the battery up. The problem is when I want to start it, especially after sitting for a while, often it will crank and crank but won't start. It's acting like it has no gas. When I take the aircleaner lid off and dump a little gas in, it fires up just fine then runs perfect after that. Even after it has been used as a daily car after that, when I shut it off, sometimes it will start just fine, other times it won't, then I have to use the gas can again. It has a mind of it's own. When you think it will restart, sometimes it won't. I've been keeping a little gas can in the trunk in case it does happen at odd times. With the gas can, it will always restart. I've talked to a few shops about this, they have no idea what might do this. Naturally, when I brought it in to show it to them, it would ALWAYS restart for them. Getting rid of this car is not an option for me, I love the car, except for that part of it.
View 10 RepliesI wanted to no why my car has water on the spark plugs not a lot though couple drips on the threads and on the part u gap(numbers 3 and 5 both are side by side), the oil looks like a light chocolate shack, it also spills a lot of water out the exhaust pipe. sort of like its being sprayed out non stop. i haven't did a compression test but all plugs are removed I am thinking its a head gasket. And the rest of the spark plugs look good just numbers 3 and 5 were wet.
View 19 RepliesI have an ' 89 Chrysler Lebaron coupe in very good condition. The car has an overhead console which is digital. It shows the compass and outside temperature. The compass works fine, but the outside temperature is always way off, normally about 30-40 degrees higher than it should be. I was told that the "thermometer" for that is located somewhere behind the grille. I am unable to locate it and am unaware of what it looks like. Auto part stores in my area don't seem to have a listing for this part. Most of these cars were convertibles, so only the higher end coupes had this option, I'm told.
View 3 RepliesChrysler 1998 Lebaron. The door locks will run constantly, they go up and down when driving and when parked, the same with the lights...now finding that in the middle of the night the car alarm is going off for no reason...also finding that the dome light will not shut off
View 2 RepliesI have a 1994 Chrysler Lebaron. The issue I've been having is for the last two weeks, my oil pressure gauge starts very high(out of normal range), and stays there for a very long time. Whilst it's at the highest possible level, the engine starts to heat up, until the gauge goes into range. This all happens without the car moving. If I leave the car on for 30 minutes(without moving it) the gauge goes into normal range, and for the most part operates normally. I have disconnected the Compressor's belt, in order to be able to turn on the engine fan from inside the car. As long as I keep the fan on, the engine stays cool for the most part.
I have considered that it was sludge, as it would soften as the engine heats up, but I have done an engine flush(machine), and the issue continues.
So far every mechanic I take it too, acts like it's impossible for the oil pump to have any issues, and claims it's normal behavior, which it's not.
My Grandpa has an 88 Ranger 2wd with the 2.9l V6 and a 5 speed, I believe, M5od. I was driving down the highway when I heard a noise. I tried throwing the tranny in neutral but when I pressed the clutch pedal in, I had no pedal whatsoever. Engine took awhile to restart. It'd turn over a little almost as if a rod was bent or something of the sorts. Eventually the engine started and would stay running as long as the clutch was pressed in (disengaged).
The engine dies no matter what range the transmission is in,neutral included unless the clutch pedal is depressed. It Will die when the clutch is released in any gear with no forward movement that is noticeable. I can spin the tail shaft with the driveshaft installed and all gears in neutral but the input does not spin at all. Input shaft wont spin at all, period. I originally thought the slave cylinder was KIA but now I am very confused on what the problem could be? Is there a bearing the input shaft rides on that may of seized?
I pulled the tranny last night and took the top cover off. Yes, I made sure it was in neutral when I removed the cover. I can manually shift the collar to all gears by hand, 5th and reverse included. I'm stuck between a rock and a hard place here and where to go from here. I have bought a new clutch assembly and slave cylinder. This truck was bought by my Grandpa brand new in 1988. It has 98,000 miles and everything is original. I did forget to mention that there was very little oil in the trans when I drained it and it appeared to be gear oil vs ATF.
I recently bought this cavalier about a week ago its and 88 automatic trans with 1.8 4 cylinder I thing not that it matters much. I noticed the exhaust had a smaller pipe from the manifold and the rest was strung with a bit bigger pipe and was attempted to crimp the pipes togather it was loud so I crimped thhe pipes better and used exhaust glue to patch the holes it runs better now to a point. but when I start the car it revs up a fair im guessing 3 grand since I have no rpm gauge but then it dies down to a low idle to the point were the car shakes a little bit.
with the exhaust fixed I can get it up to 20 kilometres an hour with my foot off the gas when I turn fully it wants to lurch ahead/backwards. when I took it out for a highway drive today I came to a stop sign so I slowed and stoped and the car stalled out. started no problem. but I also tried later putting it in neutral and it doesn't stall as I role to a stop it doesn't shake in neutral. I would like to have this fixed but I need some pointers as of were to look. im not sure if this means anything but when I got the car it had a bad enough radiator fluid leak at the hose meeting the heating car on the engine side of the fire wall I repaired that and no longer leaks.
My 1988 Mustang 5.0 GT has stalled out once last year and again recently. Same situation. I drove it for 300 miles with stops about every hour and a half. Pushed to to 90 MPH at times. Ran fine other times on the road for more than two hours. But all of a sudden the engine dies. Electrical all works but won't turn over. If I sit in it for about 10 minutes, it will start and run for the next 5 to 10 minutes than a cough or two and pull over. I have had new plugs put in and also replaced the whole distributor. Ford mechanics have stared at it and scratched their heads and say it is running fine when they hand it back to me.
View 2 RepliesI have a 2005 town and country that was running fine and when my wife picked me up today and was waiting idle it died. She didn't try to start it right away and when I got out there tried to start it and it fired then died and now it won't fire at all. It turns over fine but just won't fire.
View 2 RepliesMy 98 Chrysler sebring has a fast idle at about 1500, occasionally dies but will restart, and has been making the garage smell like gas. Can't seem to figure out the problem.
View 4 RepliesI have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 Replies