Chevy - Suburban :: 2003 - Programming / Calibrating Quadra Steer Module?
Nov 26, 2014
I bought a 2003 2500 4x4 suburban a couple of weeks back. The seller had purchased and installed a new module for the quadra steer system before I bought it but hadn't had it programmed yet. Not sure what's involved in programming the module - something best left to a chevy dealer? From what I understand, quadra steer is relatively rare because GM had priced it out of sight, but those who have it love it so I want to get it working (seller told me he can do a U-turn on a two-lane road + a foot or so of shoulder on each side - pretty unreal for something that size).
View 3 Replies
Advertisement
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 Replies
I have been having problems with the rear heat & ac. It was blowing intermittently then we would have to tap the panel in the back right side to get it to work, it won't blow at all. Is it the blower motor?
View 1 Replies
Where the factory amplifier can be found in a 1997 Chevy Suburban LT? MY Suburban still has the original radio with tape deck and with the 1-disc CD player under the A/C controls. I have already replaced all 6 old '97 speakers with new ones, and I would also like to install a better aftermarket amp with a sub woofer.I looked inside the rear quarter panels, under all seats, underneath the middle console.
View 5 Replies
I have 2002 Chevy suburban. Recently, a high pitch whine has developed. When accelerating the whine intensifies. I replaced the alternator ... No change! What could it be? Speedometer cable?
View 8 Replies
The truck we have is a 1999 Chevy Suburban 1500, 2-Wheel Drive with a 350 vortec engine. We replaced the upper and lower intake manifold gaskets with no leaks for about a week and several hundred miles then it started leaking oil and then antifreeze after that.
View 3 Replies
My husband replaced the brakes on my 2005 suburban and they are squealing constantly now. He says it's normal and will go away as I drive it, I've only done about 3 miles so far but no better. So keep driving or something isn't right? For what it's worth he grew up in his dad's auto shop and has restored some cars so not a pro but definitely competent and he swears they are installed correctly.
View 16 Replies
I have a 2002 chevy suburban 4wd with 156000 miles.. I had tires replaced last week due to them being chopped. They caused a low humming noise between 65-70mph. That was coming from the front.Below or above this speed the sound was not noticeable. I had new Coper AT-3 tires replace all around and balanced 5 days ago. The noise has become worse and starts at 61 mph and gets louder up to 70 an with a slight vibration . I have not gone above that speed to se if the noise goes away as I feel a bit uncomfortable going any faster with this issue . The tires were balanced so was wondering if I have bad tires or if the new tires being all terrain are causing more strain on what could be a bearing. The wheel bearings are fine and the rear bearings and pinion bearing were replaced two months ago . I know all terrains will make noise but not to this extent .
View 2 Replies
I have a 1999 Chevy Suburban and for some reason I've having this problem the my one brake on the passenger side won't light up when you press the brake but the other side will. And also when I apply the turning signal on the passenger side it blinks really fast and you can see the front signal flashing fast but the back does not flash at all. So for some reason the brake and signal lights don't work at all on the back passenger side. But the running lights do go...
View 14 Replies
So yesterday my truck decided to start giving me fits right after it finally got extra cold and snowy here! I noticed early on this fall that my water pump was leaking, so I replaced it. I also found that my truck only blew hot air while in motion, and cold air while it was stopped or at idle. At this point I replaced the thermostat and housing. I originally had the stock setup with the combined thermostat and housing. The new one is and updated GM version with the separate thermostat and housing assembly. Everything seemed to be ok until yesterday morning.
This is where my problem is now. Yesterday on my way to work, the message center said my coolant was too hot. The temp gauge showed the truck at about 250 degrees. My speed was only about 45mph and it was 6 degrees outside. I ended up parking the truck and looking at it after work. I found it was still doing the exact same thing. When I investigated further, I found that the upper radiator hose was hot, while the lower one coming out of the thermostat housing was cold.
At this point I figured that I had a bad thermostat, and bought a replacement. I tested the old one on my stove top in a pan of water and found that it did actually open at about 175 degrees, so I'm not so sure it was bad now. With the new thermostat installed, the engine is no longer overheating and the temp stays around 235 while driving. However, I am back to the heater blowing cold air at idle and while stopped, and warm air while driving. In addition, the rear heater now only blows cold air, it never warms up.
View 2 Replies
Took my 99 XLT super cab to a Ford dealer to have a new key made (I have only one so can't do it myself). I was told the PAT (Passive Anti-Theft) module wouldn't communicate with their system.....
As I understand it, the PAT module communicates wirelessly to the key module under the steering column. Since the PAT module is obviously working (the truck cranks, starts and runs fine). What are they talking about?
View 14 Replies
I have a 2001 Chrysler Town and Country w/ 3.8L engine and 196,000 miles. Several years ago the transmission was rebuilt. Since then the speedometer was off 1-2 mph at 65 mph. I recently bought new tires and now the speedometer is off 2-3 mph at 65 mph. My question is: How do you calibrate the speedometer? I know all about the reset for a bouncing/stuck needle. That does not calibrate the scale. I've read about gear replacement and found the Hyper-Tech calibration programmer (which is not available for the 2001 T&C).
View 5 Replies
Rebuilt the front end last year on this truck. I now own it. Front end is really tight, not as in hard to steer. It doesn't straighten up when you go around a corner completely. Going straight it drifts, 0 slack in the steering wheel. Constantly correcting it. Now my 95, I can turn it slightly going down the highway and it will turn back straight.
View 11 Replies
I am at the point where I am going to change my tires on my wheels. Currently running BBS RC's which are 8x17 ET32 with tires 225/45/17.
For those who are running wheels with such specs or more "exagerated" have you had your odometer recalibrated to respect the new rolling diameter change or not? If yes what was your easiest solution. I know depending on wheel/tire sizes, various factors can be affected including speed indication.
From all the websites I have seen and asked, I am told that I can go as less a 215 wide but not lower than 45 in "thickness" (if I stay in 17).
My objective is to of course remove rubbing during load and go a bit lower and therefore do not know if 215/45/17 will be enough of a change from 225/45/17.
View 4 Replies
My 7.3 power steering is acting up. Feels like I am up against a rock. At slow speeds like parking lot maneuvering I struggle to turn wheel. Then all of a sudden I'll get power steering back and wheel will rapidly turn. Freaky.
Brake pressure is fine. They shutter pretty bad even with the new rotors I just put on but they have good pressure. But the steering is intermittent or no power steer.
I saw online to run engine at 2000 rpm and try steering but no change. Still no power steer. There is fluid in reservoir. There is fluid seeping up steering column from steering box. No clue if this is related or unrelated.
How to troubleshoot further. I hate throwing parts at problems before truly diagnosing. Also have pretty aggressive lurching during turns in four wheel drive. It's present on dirt road but worse on pavement. Don't know if this is related or not.
View 3 Replies
I've got an E99 powerstroke. Recently it's been getting hard to steer, if not impossible. When I'm parked i can't turn the wheel and it gets better if i Rev the engine up, driving is usually ok and going around corners. It's just low speed, low rpm that it won't.
Also every once in a while when braking it feels like i lose all power brakes. The pedal goes to the floor and the brakes let go, then i can feel the pedal pump back up and i get a good feeling brake pedal again that actually stops well. All this happens within about a seconds time. But the steering is by far the worst.
I just did the power steering flush with atf and it didn't work. I'm thinking i need a new power steering pump, but want to ask here first to make sure. The truck has 290,000 on it, and it never has been replaced to my knowledge. I bought the truck with 147,000 however so it may have been done before that.
View 3 Replies
I have a K2500 suburban that has a rather aggressive/violent "vertical" shake when braking above 30mph... I bought it about 6 months ago and was told it just had a full brake job all around(receipts provided). The shake has been off and on, mostly reserved to highway speeds, however recently it has been constant at any speed above 30mph... Thinking it may be the rotors. I pulled the wheels off and even though everything looked brand new (as described) I replaced the rotors and put on new pads... did not fix the shake... and I had the old rotors mic'd and they came back good as new with zero need to turn/resurface.
I was told it may be the ABS, So I pulled the fuse... and it didn't fix the issue also I have no light on the dash
I was told it may be a flat spot on the rear drums, so I replaced the rear drums and it didn't fix the problem... the shoes looked brand new and had just as much pad left as the set i was replacing them with, so I left them alone.
I had happened to have new tires put on it, and they advised my pitman arm and idler arm were shot and that they couldn't do an alignment, so I replaced the pitman and idler and brought it back to be aligned which they did... this did not resolve any issues...
I spoke with the previous owner and he said he had the same issues and couldnt figure it.. he said his mechanic replaced the wheel bearings, rotors, pads, calipers, brake lines, ball joints(all receipts provided, and all these parts look brand new)...
The shake is very aggressive it makes the dash jump up and down and vibrates the hood to the point where it looks like it will rattle off.. the pedal doesn't pulse and the steering wheel aside from vibrating up and down doesn't pull or shake one way or the other... truck doesn't pull when braking or during this shake... and the second you let off the brake the shaking stops... and only ever shakes when you hit the brakes...it rides as smooth as can be when not braking...
View 10 Replies
I have a 2003 chevy venture...yesterday I went to start it and it acted like the battery was dead, but it still started. Then today, it wouldn't start at all. So I jumped it and it started. Took it to the store, and it wouldn't start again. So once again had to jump it. I brought it home and let it run for like 30 minutes. I went back out there and on the little screen it was saying security...turned it off and it wouldn't start again. But this time there was no clicking or anything.
View 1 Replies
I recently brought it in for the air bag recall. They replaced both front airbags.
Now they say I need a controller module. Does that mean the air bags won't deploy in a crash?
Are the deployed on impact electrically or mechanically?
View 3 Replies
I need to add a 2nd battery to my 2003 1500 suburban. How to do it? Or is there a Kit I can buy for it? Also would I need to change the alternator?
View 2 Replies
2003 Chevy Malibu 3.1 temperature gauge stopped working last night, this morning having trouble starting, no check engine light fans do turn on have heat, replaced the coolant temperature sensor but gauge still not working?
View 1 Replies
