Chevy - K1500 :: 1997 - Code P0300 Rough Idle
Jan 11, 2012
97 chevy k1500 with 305, engine rebuilt by shop 60k ago, last few months only drove truck 4-5 times, last time driving gave p0306, new plugs, wires, cap, rotor, cleared code, now gives p0300, took intake apart removed spider, sprayed/scrubbed each injector and poppet with cleaner, but no way of cleaning the line between the injector and poppets. No change after cleaning. Also ran injector cleaner through tank. All vacuum hoses look in good order, sprayed carb cleaner around intake to check for leaks at intake/throttle body, no leaks.
Checked TPS, IAC, MAF, Coil and fuel pressure, all good except fuel pressure was 52-54 while idle, replaced fuel pump, screen filter and main filter, cleared code, rough start and rough idle still gives p0300. Checked coil with ohmmeter, between posts A & C, Chilton says 0.1 ohms, i got 0.5 ohms, went to autozone and had them check a new coil, it have 0.5 ohms......? Can drive at higher speeds and runs smooth, but idle is poor almost dies.Checked fuel pressure after pump replacement, still ~54 psi. Stumped and don't want to throw more parts at it without a proper diagnosis. Have a OBDII pocket scan tool, but can't find manual, will try to find manual and see if I can pinpoint the misfiring cylinders.
View 7 Replies
Advertisement
I have an 88 chevy K-1500 4x4 5.7L ... My truck lacks serious power, it idles rough, sometimes wont idle at all, sometimes Truck Idles fine. I have adjusted the timing to tdc, and 4 deg. both ways still runs like crap.. Sometimes I can keep it idleing, put it in rev. or drive, and it will die. I have no power and if I put my foot in it too much it will backfire. but will only backfires when in gear and press on the gas to put a load on the motor. I have replaced the: tps, map, egr, pcv, distributor, cap, ignition coil, rotor, plugs, wires, timing chain, both sprockets cam and crank, checked all hoses for leaks, replaced the injectors, the O2 sensor and have changed the intake gaskets. And am still having no luck...... I am bout to just drop an M80 in the gas tank and watch her burn..
View 14 Replies
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 Replies
I have a 100% stock 2004 Celica GT ~125,000 miles. Over the last few months I have been getting a rough idle and stumble at low rpms. The other day the car would not restart after sitting for about 20 minutes. Only recently has it actually thrown a DTC. The error codes were for misfires (P0300, P0301,P0302,P0303, P0304). I don’t get a code every time but the problem seems to be more noticeable if the car has been ran for a while, sits for 20-30 minutes while in a store and then when I try to start it when I come out of the store is when the problem most often occurs. When it restarts it will stumble at low RPM and if I hit the gas it has little response and misses badly. I have never used a scanner until now. I am using a Autel MS509 scanner and I am not sure it is giving me the correct diagnostic numbers for the live data. I think the DTC are correct but the live data is questionable.
Here is what I have done so far.
- Cleaned IAC valve (completely removed and cleaned)
- Searched for vacuum leaks using carb cleaner
- Cleaned MAF sensor
- Replaced all 4 injectors
- Replaced upstream and downstream O2 sensors
- Replaced Coolant Temp Sensor
- Ensured cam tensioner is providing adequate pressure to the cam chain
- Tried 2 sets of new Iridium NGK plugs and a new set of Bosch Copper plugs
- Moved coil packs around
- New air filter
- New fuel filter
- SeaFoam through intake and gas tank. I have not mixed in the oil.
- Compression Test (1=190,2=190,3=160,4=178)
Things I have not done.
- Taken it to the stealership
- Fuel pressure test
- Valve Clearance
I am concerned about the compression test because according to the service manual it should be around 218. I was using a Harbor Freight compression tester and I am not 100% sure I had a good seal with the tester.
View 14 Replies
Just did the timing chain, phasers, oil pump and lash adjusters on my 05 5.4 s-crew. Always had a bit of a rough idle but now it's worse. If the truck idles for an extended period it sets a p0300. Just off idle the misfire is gone. It does seem a touch down on power but otherwise runs great. I did have the plugs out during the work. I cleaned them, applied anti seize and re installed. The previous owner had the plugs and COPs changed 10k miles ago. Plugs are motorcraft and coils are aftermarket.
I monitored with oreillys crappy scan tool and the miss only happens at idle. It is not a dead miss; unplugging COP on each cylinder still makes it worse.
Truck idles warm at like 570 rpm and if I hold my foot on the pedal to raise rpm a bit miss goes away.
Each cylinder is logging misfire counts with no rhyme or reason. The only thing odd during the timing job was 4 spark plugs were partially loose.
I'm sure the timing is correct; I used the OTC crank tool and for timing kit. Truck has 150k, front 02s are fairly new...
View 4 Replies
I am doing a side job and this thing has a rough idle. I put the scanner on it and pulled code 43 ESC and a ritch and lean code from the O2 sensors. I know the O2 codes are probably from running rough. It has been a while but could the knock sen be the problem or the ESC itself? I looked for the ESC by the throttle body but didn't see it. I remember what they look like but this is a late model 94 are they some where else?
View 4 Replies
My 1992 chevy k1500 blazer full size is having trouble shifting from 1st and 2nd and 2nd to 3rd. I reset the linkage it did fine for a day and now it's doing the same thing but it almost goes into neutral while shifting into some gears. And seems to lack power, the 92 doesn't have cyanoids and the transmission was redone 2 years ago when I got the truck. Could this have anything to do with the fuel filter? I know the transmission isn't bad. The Rpms are shooting up way too high.
View 1 Replies
I got a 1997 sonoma which has a p0300 code. I changed the plugs and wires, cap and rotor and the pcv value, and it still misses. what could this be?
View 18 Replies
I have a 2000 Suburban 4wd that has a p0300 code. The misfires are coming mainly from #2 and #7 cylinders. Misfires only occur at idle. over 1500 rpm the misfires disappear. I have put new A/C Iridium plugs in, new wires, and new coil packs on both cylinders but the problem is not any better. All 8 fuel injectors all go to 55 psi when activated and drop to 28 when released. All tests were done with my Snap-On Solus.
View 2 Replies
What that means? The check engine light is NOT on but I looked for a code because my truck is idling rough, and when driving, when the overdrive kicks in, it vibrates really bad. As if a bad U-joint on your drive shaft. The truck has been in a field for about 5 months broke down so any clue? Haynes manual says nothing about P1000.
View 13 Replies
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 Replies
97 4.6.. So it would appear that I have the wild goose chase of codes. The major symptoms are rough idle and very poor performance. I started off by cleaning the egr valve and ports. Then I checked the egr valve itself and watched the valve open and close under a vacuum. I was suspecting the DPFE sensor but I wanted to trying something else first. I was under the Impression that if at idle you apply a vacuum to the egr valve it would cause the engine to "stumble and stall". I did this and there was no change in the way the engine was running. So now I'm lost as to where to go from here.
View 3 Replies
Just got a 98 f150 w/ 5.4 4x4 excab. It idles fine but under light accleration. It starts bucking and missing bad, if I step on it, it down shifts and accelerates fine. If I try to maintain one speed it misses bad. It is not throwing any codes right now. The check engine light did come on for like a minute but went back off before I could have it read. I hooked up a scanner just to see if any codes were stored and got p0300 and p0301. I am going to clean the MAF and check for vacuum leaks. I hear the rear plug and coils can get water in them causing similar problems.
View 8 Replies
I have a 2000 Toyota Avalon XLS with 134k miles, engine is a v6 (3.0). It has a rough idle and a steady misfire. You can drive it sometimes and it will run perfect and you can drive it sometimes and it will misfire. I am getting codes P1150, P0300,P0302, P0304,P0306. Driving me nuts.
View 1 Replies
I am thinking that maybe my ignition switch is bad and needs replaced. When i turn the key on sometimes the pump wont turn on and thus wont start (brand new pump couple weeks ago)
all my fuses are good
its only done this once but today it started fine ran for maybe 2 or 3 seconds and then died just like i turned the key off no sputtering or anything but started right up again and was fine
sometimes it feels like its lost power and burning alot more gas then it should and every now and then at higher rpm it will miss but only once and it very rarely does that
relay is good
ground to fuel pump is good
View 14 Replies
I have a 98 k1500 5.7 vortec. I was driving and the next thing I knew my truck lost power and would misfire at an idle but only when under a load (in drive with foot on brake). The last time something like this happened an injector came out of place. So that's where I started. I wound up changing the whole spider injectors and ALL the gaskets, upper and lower. I put everything back together and the problem was still there so basically I am back to square one.
I then pulled spark plug wires while running to see if I could isolate the misfire and found that I could pull all 4 wires on the passenger side without any difference in while it was running. So basically my truck is currently running on 4 cylinders and they all happen to be on the driver side. I checked my compression on the passenger side and all 4 cylinders have 180 psi so that rules out the head gasket being blown. I am getting 4 codes , 520, p1345, p0155 and p0161. I know that i have to get tge truck properly timed with a computer but i don't think that would cause my problem.
View 5 Replies
I have a 1995 suburban k1500 4x4 i just pulled a check engine code 35 what could be causing it to appear? I need to know if its something small or a big fix?
View 2 Replies
I have a parasitic drain on my battery. 4.5 amps to be exact. I've tracked it down to the CTSY fuse or Fuse 3 in the fuse block. When I pull the fuse it drops to 40 mA which is pretty normal.
What is the most likely cause of this drain since my lights seems to be working and shut off when the doors are shut? I've almost got the dash ripped apart to get at the wiring harness but hopefully I can find it before taking the whole dash out.
View 6 Replies
I had to choose the Yukon, as there is no Suburban?
Anyway, I have a very bad misfire in my truck. Lopes at idle stumbles under load. Through substitution, I have tested: module, coil, and crank sensor. I have replaced: plugs, wires, cap, rotor, air filter, fuel filter and upgraded from SCFI to MFI (can you say "expensive best guess"?).
Still getting P-0300, P-0302 and mostly P-0304, using a Snap-on Modis scanner.
Compression tested today: all cylinders between 160- & 170 psi. After this, leak-down seemed redundant.
Back pressure test: 0.5 psi at 2500 RPM, both banks.
Steady fuel at about 60 psi.
I am going to pull distributor (175K miles) and examine drive gear. Not too sloppy at rotor bearing. However, how do I set baseline timing when I re-install distributor? If the distributor is OK, what test or part should I look at next?
View 2 Replies
I have a 2000 jetta 2.0, and the idle seems to rough and when I start the car it seems like I might stall.
View 9 Replies
Yesterday I went to star my 2.0 Jetta and it instantly starting sputtering at idle. After maybe a minute of sputtering the car died. Tried restarting it and it would instantly die after starting. Car threw code P0300: Random Misfire.
As of today the car now runs again with no problems. No codes. I didn't touch a thing and it seems to have resolved itself.
The entire engine bay was wet from condensation due to temperature change. Is there any way this could've contributed to the misfiring? I'm thinking the spark plug wires might have gotten wet and that was causing the misfire.
View 2 Replies