Chevrolet - Suburban :: 2003 Misfiring At 50mph Or Higher
Jun 25, 2012
I have a 03 Suburban LT with the 150,000 miles. and it misses out at 50mph or higher. I thought it was the transmission, and the tranny guy confirmed a new transmission was needed, but said he thought the missing was maybe the coils. the local Chevy dealer did the diagnostic, and determined the coils, plugs, and plug wires were all good. I 've replaced the oxygen sensor as well. The service manager said to keep driving it until the Check Engine light comes on. That concerns me, but hey what do I know. The mileage hasn't dropped off, and it runs fine the rest of the time.
View 5 Replies
Advertisement
I am working on a99 2500 4x4. 7.4 Replaced 230,000 engine with 90,000 engine.I had to fix a bad oil leak from the oil pressure sensor. Replaced it and delivered it.
Ran great Gal was driving at 50mph. Engine died and wouldn't start. She fried starter trying. Replaced starter, has no codes. 59-60 lbs fuel pressure with key on then holds 50 lbs. 60 lbs while cranking. Has spark at plug. NO security light staying lit or flashing. flashes then goes out. Smell of unburnt fuel is strong. Also no oil pressure at gauge when cranking and her key fob doesn't work.
View 13 Replies
My 2003 Suburban shakes when I drive over 70 mph. I don't know if the tires need realignment?
View 4 Replies
I have a failing 2003 Chevy Suburban instrument cluster and wonder if I can replace it myself. All I have to do is remove it and re-install it when they send it back. 4 bolts and one plug. No reprogramming. What could be easier? Is it really something I can/should do? -
View 3 Replies
My trailblazer started with the spitting and sputtering (misfiring) last week. Over 100,000 miles on it, ya, in need of a tune up. So for obvious reasons new spark plugs seemed to be the logical choice. If it wasn't the problem, it can't hurt to change them. Truck's SES light did not come on, but truck was running pretty crappy, more when it was cold than hot, but definetely a loss of power. There is also a slight exhaust leak starting, where abouts right now I haven't pinpointed, deaf in one ear so it's hard to tell where it is coming from.
So I had my brother in law install the new spark plugs. We took the old ones out and 4 and 5 cylinder plugs had oil on them. Ah great, valve cover gasket and the gaskets the spark plugs sit on (don't ask me, not a mechanic lol) need to be changed. Started with just the plugs for now. Started truck up, still had a bit of vibration on idle, like it would from an exhaust leak, but still didn't seem right . But an even more noticable loss of power when driving, truck doesn't seem to want to get above forty.
Now my SES light is flashing almost consistently unless I'm stopped (idled). It almost feels like the cat is clogged. Did smell a heavier than normal gas smell when changing out the plugs. I know that the flashing SES almost certainly means a misfire. But why would it all of a sudden come on after changing the plugs? Tomorrow I am going to my friends garage who has the scanner tool (not just the one that reads codes) to see if it is a bad coil pack and to see if there is a specific cylinder that is misfiring.
But there is something about that exhaust leak that is leading me to believe it is the culprit of my problems. Leak came first, then the misfiring. Could the cat be clogged, which blew a hole in the exhaust and cause a misfire? And the new plugs just made the misfiring worse to cause the SES light to come on? Is there anything else I should check besides a faulty coil pack and compression check (even though I should have done that when I changed the plugs, but live and learn).
View 7 Replies
I had to choose the Yukon, as there is no Suburban?
Anyway, I have a very bad misfire in my truck. Lopes at idle stumbles under load. Through substitution, I have tested: module, coil, and crank sensor. I have replaced: plugs, wires, cap, rotor, air filter, fuel filter and upgraded from SCFI to MFI (can you say "expensive best guess"?).
Still getting P-0300, P-0302 and mostly P-0304, using a Snap-on Modis scanner.
Compression tested today: all cylinders between 160- & 170 psi. After this, leak-down seemed redundant.
Back pressure test: 0.5 psi at 2500 RPM, both banks.
Steady fuel at about 60 psi.
I am going to pull distributor (175K miles) and examine drive gear. Not too sloppy at rotor bearing. However, how do I set baseline timing when I re-install distributor? If the distributor is OK, what test or part should I look at next?
View 2 Replies
I have a 2003 Nissan maxima and at first it used to shake at around 50mph, took it to the shop they looked into the suspension, did wheel balance, changed 2 front tires and wheel alignment and they said it should be fixed. A week later, it started shacking at around 70 mph, what else should I do to get ride of this problem?
View 1 Replies
If sensor or control module malfunction. Brakes are fine. If ABS relay, so where is it located, cant find in fuse box. This is a 1500 2WD suburban.
View 5 Replies
I have a 1990 suburban that has had a rebuilt x-mission about 50,000 miles ago. At this time when I drive there is a hesitation, split second, when running on flat road. It happens when going up a hill, too.My mechanic said change the: plug wires, then the plugs and rotor. No difference.
I think the thing is dropping out of OD for a split second and then going back in. If I drive in 3rd, I don't think it is happening. Isn't there a relay or solenoid that controls this function?
View 2 Replies
I have an '05 Suburban with starting issues. When it's cold out (below 40 degrees) and you turn the key, all accessories come on but truck will not crank. It then seems like the power just cuts off.......dash lights go out but gauges are fixed in place and a couple of seconds later, I hear a strange buzzing noise from the dash area behind the radio and the gauges will then go to power off position. Then if I try to start it, there is nothing, no lights on dash, no starter engaging, no clicking of the relays, nothing. I tried, on a hunch to disconnect the ground lead from the battery. Had it off for 10 minutes or so, put the cable back on, tightened it down (wasn't loose to begin with) and it started right up first try in 20 degree weather. I had previously had the battery and alt checked and both were good.
View 3 Replies
2007 Chevy Suburban, 65K milesLet me start by saying I took this into to the dealer and they found nothing!
When I accelerate, I get a "flutter" in the engine. The best description of this flutter is that the RPMs go down about 200 or 300. I think it feels like it is sluggish when it accelerates. It is most obvious during the 35 - 60 MPH range, but you also see it when cruising at 70 MPH.
I tried adding some fuel treatment and ran some 93 octane through it to see if it was the fuel injectors, with no change in the behavior. No error messages or engine light is on. Regular oil changes and services (60K service, every 3K miles for oil change). Driving behavior has changed since I bought a Prius 3 months ago. It used to be driven 40 miles / day (+ long trips) and now is driven about 40 miles / week (+ long trips).
View 1 Replies
1995 Chevy Suburban, currently at 150,000 miles, Prior owner had transmission rebuilt prior to 100,000 miles. While towing my 18ft camper trailer on a recent trip every time I started off from a stop I had to really push on the gas to get going. At first I though the emergency brake was on, or I had a flat tire. I then noticed the automatic transmission was not shifting when I had it in D. Checked the transmission fluid and it was full. The transmission seems to be stuck in 3rd gear. When I move the shifter to 2 it will shift down. Reverse is also still working. Am I in for a costly repair?
View 3 Replies
I have random power drop off (best description is a loss then a surge or something like a skip) when driving over 60 mph. If I let off the gas or floor it the problem goes away temporarily. No mechanic has been able to figure it out. Chevy dealer just says "we don't have any codes".
View 10 Replies
2002, Chevy, Suburban 1500, 4wd, 5.3L engine, 210,000 miles. Mass airflow sensor and both O2 sensors replaced last year in an effort to fix this problem. Original problem surfaced when the vehicle was shut down or running uphill and had about 1/2 tank of gas in hot weather. If stopped, the vehicle would not start until it had cooled down. Sometimes getting it onto level ground would be enough to get it running again. ( This accomplished by turning on the key and allowing the vehicle to roll back out of the parking place. ) If running down the road, getting to level ground after the stall, pulling to the shoulder and cooling the engine/waiting a few minutes and restarting the vehicle would work. This was before the above mentioned repairs.
Last weekend in 60 degree weather I was driving back from northern Michigan and as I headed up hill at 75 mph with the tank at 1/2 the vehicle did a high speed stall on me. Symptoms were: RPM showed 2000, but pushing down on the gas actually dropped the RPM no matter how feather-footed I was. This was tried several times. I turned on the 4 ways and moved toward the shoulder and at 50 mph finally got the thing to restart. The rest of the trip home was uneventful.
I had a 2001 Suburban with the same specs which did this same thing until a factory recall that got me a new fuel pump. I asked about the recall the last time my truck was in for service and they said it does not fall within the serial numbers for that recall. Fuel filter replaced about 9 months ago. Co-incidentally but not necessarily related is that my battery with less than 3 years of a 7 year warranty was draining itself in less than 2 days this last winter.
View 8 Replies
I changed my plugs recently in my 2004 Chevrolet TrailBlazer 4.2l I6 with the coil on plug setup, and now it is misfiring and hesitating when I hit the gas. All the spark plugs have the proper gap and torqued down properly. I tried tightening down the ignition coils and on one I snapped the bolt. Of course my truck is staying parked until I replace the part which I have to order online. The only thing I can think of as far as the misfiring is not having a proper seat with the coils, my question is, how to get a better seating or if there are any other possible issues I could have over looked at all?
View 9 Replies
I have a 2004 suburban with approximately 125k miles on it, it is nominally my wife's car.
Recently it seems to not be able to access the last 1/4 tank of fuel. A couple of weeks ago my wife (who likes to run it down to the dregs) got it sub 1/4 tank, and it cranked but didn't start...put in 2 gallons from a can, started right up...took it to a gas station, filled it up (less the approximate 1/4 tank of fuel).
So, fuel pump? Pickup clogged? If so, what does it take to replace/repair...
View 5 Replies
86 Diesel Suburban
Lately the voltage gauge sometimes starts to wander upwards toward the 18v red zone. When it does it wanders up and down a lot, but mostly well above the center 13v. Sometimes I left of the throttle a little and it goes back and stays at normal, and sometimes it doesn't and bounces up again as soon as I press the throttle. Doesn't happen on every drive, just sometimes.
I thought it unlikely this was a bad voltage regulator, since it's a pretty new alternator, 2 years tops. So I thought I'd see what other possible causes could be. (Why do they make the voltage regulator internal to the alternator now anyways, since they seem to go bad more often than the core? Can I just add an external regulator like the older trucks had?)
I've heard over-voltage can ironically sometimes be caused by a short, since the regulator dumps more voltage into the field coils because the main coils are showing they aren't delivering enough current (because it's all being soaked up by the short), resulting in an overall over voltage as the alternator tries to compensate for the voltage drop of the short.
How do I tell if this is the cause of the overvoltage or if it's something else instead? If it is a short, where could it be? I'm assuming it must be somewhere weird, because almost any normal place I could think of for a short would simply blow a fuse. Or is there such a thing as a partial short-- high enough resistance to not blow a fuse, but low enough to drive the alternator nuts?
Could it be related to overheating? I initially thought that was a possibility, because it began around the time the weather turned warm here, but on any given day it seems pretty random and not tied strongly to excessive speed or going up hills.
View 9 Replies
2002 1500 4WD 126K miles. A/C not working, compressor does not engage when A/C is switched on. Is there an interlock if the refrigerant level is too low to keep the compressor from engaging? Original owner, A/C has never been recharged. Is recharging my best first step.
View 2 Replies
I have a 99 Suburban with very high miles. Going on 306K mostly highway miles. This is our baby and the best vehicle I've ever owned. This is a solid vehicle that I think we can get more miles out of.
The problem is that it will intermittently surge or shudder between 40-60mph during acceleration. It's hard to pinpoint because it doesn't happen all the time. It seems to be worse if the vehicle is low on gas or the engine is cold but I'm not certain about that. It's not hard enough to call a buck, jerk, or sputter though. Maybe I've over-analyzing but basically it will shift to the correct gear and then back down then back up etc., and back and forth for very brief seconds. Then levels out after 60mph and there are no other problems. If the gas is low or engine is cold is does this in lower gears as well but usually only around 4th gear. I hope this description makes sense.
Here's where I'm confused. The transmission was rebuilt 2 weeks ago specifically the torque converter and rear planetaries. The day we got it back we performed a tune-up so all new plugs/wires/cap/rotor. The fuel filter was replaced about 8 months ago and the fuel pump 2 years ago. All regular maintenance has been performed on time since we bought it 4 years ago. Yesterday the Service Engine Soon light came on and it only showed one code (OBD II), PO161, so we replaced the 02 Sensor (Bank 2, Sensor 2).
However the problem persists and there are no other codes providing any direction. I've tried to search the internet for drivers with the same issue but the fixes vary too much and seem uncertain.
Other known issues for diagnostics: four wheel drive hasn't worked for years (haven't needed it in our flatlands) and ac compressor went out last spring.
View 5 Replies
I have an 82 GMC suburban with a 6.2 diesel, TH400 transmission and a NP265 transfercase. The last day of June we moved from Greeley Colorado to Southern South Dakota. Tems were as high as 107 that day. I had to stop several times to let the transmission cool. I didn't want to burn it out. I was towing a Hyundai Accent (2002) on a Uhaul Car Dolly. The trans temp gauge registered as high as 210 degrees. If it got hot I would stop and let it cool. However recently I changed the rear axle, the pinion spider gears seized and exploded. I think I went from a 3.73 gear to a 3.08. However I am not certain. Certainly seems like it when I pass people at 30 according to the speedometer that used to pass me. However, recently it seems to have developed an occasional shudder as I accelerate. It's mainly after alot of in town driving. I checked the brakes, serviced the rear end, and checked the fluid levels.
View 1 Replies
My 06 suburban is causing problems. Every time I come up to a stop sign or intersection and slow down then give it some gas it seems to stall. I then have to take my foot off the gas and wait a second and then slowly give it gas again. The engine isn't stalling though . I had it in to midas and they cleaned/ washed out the throttle area ?
View 4 Replies
