Chevrolet - Suburban :: 1998 - Engine Hard To Start When Cold Outside Or After Rain
Jan 29, 2013
I have issues with engine starting when cold outside or after rain. This only happens when engine is cold and has not been started for a day or 2. Distributor cap does not have any condensation inside but does seem to corrode on contact points. Engine turns over fine, has fuel and spark. When this happens engine will not fire and after awhile it will start to fire and lock up when it fires then continue cranking. After repeated attempts it will start and run fine, can be shut off and start right back up with out any issues. It could take a few tries to a few hours of trying before running though. I'm leaning toward a distributor or timing issue. Am I on the right track? 98 Suburban K1500 5.7L ....
View 6 Replies
Advertisement
I have an '05 Suburban with starting issues. When it's cold out (below 40 degrees) and you turn the key, all accessories come on but truck will not crank. It then seems like the power just cuts off.......dash lights go out but gauges are fixed in place and a couple of seconds later, I hear a strange buzzing noise from the dash area behind the radio and the gauges will then go to power off position. Then if I try to start it, there is nothing, no lights on dash, no starter engaging, no clicking of the relays, nothing. I tried, on a hunch to disconnect the ground lead from the battery. Had it off for 10 minutes or so, put the cable back on, tightened it down (wasn't loose to begin with) and it started right up first try in 20 degree weather. I had previously had the battery and alt checked and both were good.
View 3 Replies
'99 K1500, 5.7L, 130K miles, regularly serviced and well maintained, no garage so sits out in weather. About 8 months ago we started to experience no starts after rains, engine would fire off, but not stay running, security light NEVER came on. Took to regular mechanic and had fuel pump replaced (needed it anyway), wiring "repaired" behind dash. No problems till last month, then same started again. Sometimes will start after 5-6 tries, other times will not start till 10-12 hours AFTER rain stops.
Security light came on ONCE while driving for 5 minutes, then went out. TSB's indicate possible corrosion in the Passlock sensor voltage, underhood or under body connections, may be reason. Where these are as I would prefer to check them myself to see if simple solution before pay mechanic to find the same. Since did not reoccur for a while after fuel pump replaced, are there connections that would have to be pulled to replace tank that may now be not sealing again with time? Any resource for wiring diagrams for Passlock path?
View 14 Replies
I have a 1996 Chevy Cheyenne pickup with a fuel injected small block that has 50k miles. Earlier this summer the truck developed a problem where it is very hard to start when cold (after sitting overnight or after sitting for many hours on my flat driveway). When the engine is cold (say the first start of the day) I can only get it to start by giving small bursts of cranking power to the starter. That is, it won’t start if I hold the key in the cranking position but is more likely to start if I give it a short burst of cranking power (when I hold the key in “start” position) for a second or two.After the first start of the day, the engine runs fine and subsequent starts are quick and normal. The “Check Engine” light is not on and there are no trouble codes…. Other than hard starting there are no issues with engine performance.
View 2 Replies
My Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
View 19 Replies
I have a 98 chevy silverado c1500 extended cab has 5.7 350,and i think a 4L60E transmission. Driving around town my truck shifts fine, but when i get on the highway for a little while it will start jumping hard from 1st to 2nd, but if i kill the truck and start it back up it will usually shift fine.
View 1 Replies
Simple question: Is it possible that battery problem/corrosion in battery cables would allow car to crank but not start on first try when cold? (Car normally starts on 2nd or 3rd try). I've read some places that if car cranks its not a battery problem but I'm not convinced.
Background:I have a 98 Ford Mustang (approx 140,000 miles) that occasionally has trouble starting. Car normally takes 2 to 3 tries to start first thing in the morning or if it has been sitting for a while. It always cranks but doesn't turn over. I had it in the auto repair shop, they said it had to do with IAC valve being stuck open. They recommended to replace throttle air by-pass valve. The repair was done and when I came to pick up the car I heard it take three tries to start before they brought it to me from the back. I asked about it, so the service advisor said he would go and talk to the tech, he said he talked to the tech and that there was a lot of carbon that he had cleaned out and maybe remaining carbon in the system caused problem, I got the idea that they seemed to think everything was fine if I had any problems I could bring it back. The car became even harder to start, now taking up to 8 tries. I brought it back and they said that the new IAC had to be adjusted to allow more air. I picked up the car, they said it was fine, but now it still takes 2 to 3 tries to start it first thing in the morning.
In the past, I have had trouble with battery and battery terminal corrosion, have had new terminal ends put on my battery a few times, last time was probably about 6 months ago. Terminal ends look very corroded again. I'm thinking about just asking them to replace the battery cables and see what happens.
View 8 Replies
I am a laid off mechanic doing some side work. I friend of mine has a 98 blazer that will not start in damp weather. Here's the kicker, it has spark to the plugs. New cap, rotor, pick up coil, and wires. Fuel pressure is around 60psi. I think it might be in the fuel injection. I drove the SUV into my garage, While the engine was running I watered the distributer down along with the wires. It ran fine. I shut it down and tried to start it a few minutes later with no luck. I took the distributer apart to inspect it for water and found nothing. I reassembled it and still had a no start situation.
View 10 Replies
2007 Chevrolet Impala 1LT3.5L Flex Fuel EngineAuto Transmission with shift lever on the steering column29,980 miles
Bought new Nov 2006 so is now four and a half years oldThe drive train is still under warranty (6 years or 60,000 miles). All recommended service per the manufacturers manual has been done. Book calls for first transmission service at 50,000 miles
NOTE: Previously at 19,600 miles the transmission cooler line fittings were replaced due to a small leak. Currently no evidence of a leak; no fluid on garage floor and the transmission fluid level on the stick shows right on the mark. Fluid still clean pale red and has no odor.
Majority of my driving is short hops with multiple stops, so the car gets heavy use shifted into and out of park gear. I do use the "parking brake" applying it after shifted into park and released before shifting out of park. I always have my foot on the brake pedal when shifting out of park.
PROBLEM: Having trouble shifting out of park on a cold engine or if the car has been sitting for an hour or more since turned off and put into park gear. Oddly enough, if I'm running a series of errands where the car has been in park for only 5 to 30 minutes, there is no problem shifting out of park gear. But if the car sits long enough for the engine to cool then it becomes hard to shift. The longer the time it sits in park the harder it is to shift out of park when the car is started.
View 11 Replies
My 04 Chevy suburban blows cold for about 15 minutes then turns hot...sometimes it will turn back cold, but not lately
View 2 Replies
Been having this problem since this past Easter when our mechanic installed new valve cover gaskets.
When the van is hot (normal operating temperature) and you turn it off just for a minute, like to get gas, and try and restart it acts like it’s not getting enough gas. It will cough and sputter and balk. It will finally start though and after 30 second all will calm down and it will run fine.
One big problem is, is that is intermittent – meaning it won’t mess up for the mechanic and putting it on the computer shows nothing wrong.
One mechanic said it was a cracked distributor. Replaced that for $400. and same problem. I’ve also cleaned the Mas Air Flow sensor and changed the fuel filter.
View 4 Replies
Engine cranks but will not start, it kicks back after cranking over for a couple of times i have replaced the crank sensor it has done this once before it kicked back hard enough to knock a tooth off of the flywheel after replacing flywheel and starter it started fine for three months then it kicked back hard enough to break a starter mounting bolt. i replaced bolt had starter checked and replaced again?
View 6 Replies
I have a 94 Chevy Suburban C1500 with a 5.7L, 350 Engine. It has 235,000 miles on it. I purchased it about 4 years ago with 191,000 miles in very good condition and obviously well maintained. I have continued to maintain it well.
For the past few months it has begun to start a little slower that before and when accelerating cold or warm there is a spot where it looses power. It doesn't sputter or die it just looses power. I can press the accelerator farther and it will come back to life and do fine. After a 20 -30 minute drive if I park for a while, 20 - 30 minutes, when I start it up it dies. The only way to keep it running is to give it the gas and smooth it out at about 1500 rpm for 10 - 15 seconds. Then I can drive it with no problem most of the time though it still has the dead spot on acceleration.
There is a good spray pattern from the throttle body injectors. Plugs and wires are relatively new and plugs look good (AC Delco Rapidfire Platinum). When I turn on the ignition without going to start, the fuel pump builds pressure for 4 - 6 seconds. I haven't checked the fuel pressure yet and am considering investing in the rig to do so. I recently replaced the fuel filter but that didn't work.
The check engine light has not come on but many of the lights in the cluster are burned out and I haven't felt like going to the trouble to fix that so it is possible that the check engine bulb is bad.
View 12 Replies
I have a 1998 chevy blazer and I cant get it to start. I removed the starter and turned the key and can see the starter popping out and spinning, but when I put it back into the flywheel all I get is clicking noise(like if the battery is dead) I had it on jumper cables so I don't think its the battery?
View 12 Replies
I have a 2001 malibu , my cars engine light has been for about a week. This is the second time it has happened. lately I have been having trouble starting my car. Does this have anything to do with my car , or because of the cold weather? How important is it for me to get my car checked out?
View 2 Replies
Why will the 96 Blazer not start in the rain? Replaced almost all electric components from key cylinder to plugs. It is grounded somewhere when wet.
View 3 Replies
2007 Chevy Suburban, 65K milesLet me start by saying I took this into to the dealer and they found nothing!
When I accelerate, I get a "flutter" in the engine. The best description of this flutter is that the RPMs go down about 200 or 300. I think it feels like it is sluggish when it accelerates. It is most obvious during the 35 - 60 MPH range, but you also see it when cruising at 70 MPH.
I tried adding some fuel treatment and ran some 93 octane through it to see if it was the fuel injectors, with no change in the behavior. No error messages or engine light is on. Regular oil changes and services (60K service, every 3K miles for oil change). Driving behavior has changed since I bought a Prius 3 months ago. It used to be driven 40 miles / day (+ long trips) and now is driven about 40 miles / week (+ long trips).
View 1 Replies
2002, Chevy, Suburban 1500, 4wd, 5.3L engine, 210,000 miles. Mass airflow sensor and both O2 sensors replaced last year in an effort to fix this problem. Original problem surfaced when the vehicle was shut down or running uphill and had about 1/2 tank of gas in hot weather. If stopped, the vehicle would not start until it had cooled down. Sometimes getting it onto level ground would be enough to get it running again. ( This accomplished by turning on the key and allowing the vehicle to roll back out of the parking place. ) If running down the road, getting to level ground after the stall, pulling to the shoulder and cooling the engine/waiting a few minutes and restarting the vehicle would work. This was before the above mentioned repairs.
Last weekend in 60 degree weather I was driving back from northern Michigan and as I headed up hill at 75 mph with the tank at 1/2 the vehicle did a high speed stall on me. Symptoms were: RPM showed 2000, but pushing down on the gas actually dropped the RPM no matter how feather-footed I was. This was tried several times. I turned on the 4 ways and moved toward the shoulder and at 50 mph finally got the thing to restart. The rest of the trip home was uneventful.
I had a 2001 Suburban with the same specs which did this same thing until a factory recall that got me a new fuel pump. I asked about the recall the last time my truck was in for service and they said it does not fall within the serial numbers for that recall. Fuel filter replaced about 9 months ago. Co-incidentally but not necessarily related is that my battery with less than 3 years of a 7 year warranty was draining itself in less than 2 days this last winter.
View 8 Replies
For last 3 months I have faced to a problem. My 2009 2.0 TSI, misfiring in cold start (in Summer!). When engine is cold (particularly in the mornings) in FIRST start, RPM goes to 1100 and engine works hard and car badly shakes. If I continue, engine light flashes. But if I just after first start, turn off the engine and restart it again, RPM comes back below 1000 and engine works well!!.
During first start a strange noise comes from the below of the car (Check...check...check...) but in second start everything is OK.
KM is 100k. I red the code and it usually shows P0302 (Misfire in cyl 2) and sometimes P0301 and P0300. I recently change all spark plugs (ngk) but problem had started before sparks change.
I switched the coils to see if misfiring follows the coil but negative.
I know it can have different reasons, PCV, carbon build up, EGR,..... but as it goes just after SECOND start I think it should be an electrical problem.
View 5 Replies
Truck runs great if I get it started. Here are symptoms.
-Extremely hard to start when engine is cold
- It will start fairly quick if plugged in all night
- After running there is no issues with starting unless sits over night
- Batteries good and engine cranks fast
- Tests and parts I have replaced
- Replaced GPM (Glow Plug Module) I do not have the relay as most seem to have on their engines. I did replace this unit.
- Replaced Glow plugs all 8 this morning. Since they where cheap enough it did not hurt the wallet.
- Replaced crank position sensor. Tach moves when engine is cranking.
- Checked the HPOR and it has oil about 1/2" from top.
Now what is left to check besides doing a buzz test to rule out injectors? Also if truck runs fine and does not run rough could injectors still be bad?
View 3 Replies
I own a 2006 Chev Cobalt with 133000 kms (yes I'm Canadian). About 6 months ago after the car sat over night in the rain, it would not start that morning. It would turn over and cough and sputter for afew seconds but not stay running. I had it towed to my garage. The car sat there for a while and when the mechanic got in, it started no problem. The mechanic tried hosing down the entire area under the hood to get the car to act up, but that didn't do anything. I took the car home and we all chalked it up as a fluk. Then a week later , after an over night in the rain, it did it again. Towed to the garage and it fixed itself by the time the mechanic got to it. This happened 3 more time.
CAA sprayed all the ignition parts with something like WD40, they even got a hold of another coil pak that I could borrow to see it that would solve the problem.... it didn't. They put it on a code reader and it read " Camshaft positioning (CMP) sensor circuit". But they ( my mechanic) told me that they just didn't know what to do next. They recommend another mechanic, but I haven't gone yet because I'm afraid that they will look at my car as a "cash cow". For now, to avoid this problem, when I know it's going to rain, I plug in the block heater, and put a desk lamp with a 40 watt bulb under the hood, then bungy down a tarp over the hood after I close it. I would like to point out that if I go to work and the car gets rained on all day (9-5) it will still start. It seems like the car has to soak in the moisture first.
View 4 Replies
