Chevrolet - Suburban :: 1997 - Diesel Engine Dies - Dashboard Lights Don't Come On
Jun 7, 2012
My '97 Chevy Suburban diesel dies at random times. Nothing seems to trigger it; it usually happens when I'm just driving along, minding my own business; not accelerating or decelerating, turning, stopping, etc. Has happened with the fuel tank at every level: full, half full and quarter tank. When it dies, the dashboard lights do NOT come on. When I turn the key "off" and back "on", the lights come on and the engine will crank fine, but won't start. Ten minutes later, it starts and everything is fine. It may not do it again for weeks, or it may do it again in 10 minutes.
This last time, the fuel tank was fairly low -- below a quarter tank -- and it seems to "buck" or "hesitate a little just before it died the first time. The dealer replaced the crankshaft position sensor and the fuel injector pump. When it started doing it again, they ran every diagnostic test they had and could find nothing wrong. Ran fine for a few weeks, then quit three times in 30 minutes. It's back there now.
View 11 Replies
Advertisement
My diesel suburban dies while driving. It starts right back up. I have changed the fuel filter and checked for water in fuel.
View 2 Replies
What would cause the vechile to die randomly, while driving? have check all ground wires, coolant, spark plugs, air filter, and changed fuel filter. no check engine lights come on.
View 2 Replies
My 1997 chevy suburban wouldn't start after being parked for a few days. the battery seemed to drained out so quickly and not because the lights were left on. The alternator was replaced less than two years ago. and the battery less than a year ago. I tried to jump start but it did now turn orver. What is the problem?
View 1 Replies
2007 Chevy Suburban, 65K milesLet me start by saying I took this into to the dealer and they found nothing!
When I accelerate, I get a "flutter" in the engine. The best description of this flutter is that the RPMs go down about 200 or 300. I think it feels like it is sluggish when it accelerates. It is most obvious during the 35 - 60 MPH range, but you also see it when cruising at 70 MPH.
I tried adding some fuel treatment and ran some 93 octane through it to see if it was the fuel injectors, with no change in the behavior. No error messages or engine light is on. Regular oil changes and services (60K service, every 3K miles for oil change). Driving behavior has changed since I bought a Prius 3 months ago. It used to be driven 40 miles / day (+ long trips) and now is driven about 40 miles / week (+ long trips).
View 1 Replies
2002, Chevy, Suburban 1500, 4wd, 5.3L engine, 210,000 miles. Mass airflow sensor and both O2 sensors replaced last year in an effort to fix this problem. Original problem surfaced when the vehicle was shut down or running uphill and had about 1/2 tank of gas in hot weather. If stopped, the vehicle would not start until it had cooled down. Sometimes getting it onto level ground would be enough to get it running again. ( This accomplished by turning on the key and allowing the vehicle to roll back out of the parking place. ) If running down the road, getting to level ground after the stall, pulling to the shoulder and cooling the engine/waiting a few minutes and restarting the vehicle would work. This was before the above mentioned repairs.
Last weekend in 60 degree weather I was driving back from northern Michigan and as I headed up hill at 75 mph with the tank at 1/2 the vehicle did a high speed stall on me. Symptoms were: RPM showed 2000, but pushing down on the gas actually dropped the RPM no matter how feather-footed I was. This was tried several times. I turned on the 4 ways and moved toward the shoulder and at 50 mph finally got the thing to restart. The rest of the trip home was uneventful.
I had a 2001 Suburban with the same specs which did this same thing until a factory recall that got me a new fuel pump. I asked about the recall the last time my truck was in for service and they said it does not fall within the serial numbers for that recall. Fuel filter replaced about 9 months ago. Co-incidentally but not necessarily related is that my battery with less than 3 years of a 7 year warranty was draining itself in less than 2 days this last winter.
View 8 Replies
I have a 2010 Chevy Malibu with @23,000 miles. The dashboard lights will periodically click off. At this point the numbers on the speedometer, gas gauge, etc., are not visible.
View 2 Replies
My engine revs up no matter if the thing is hot or cold when I come to a stop at a red light, SOMETIMES. Other times it will idle at 100 and then wants to idle around 1000 and has idled as high as 1200. I've been told EGR, TPS, Idle Control Motor, or Intake gaskets. I did have a code 22 which occurred after a friend unplugged the TPS and reconnected it, but no other codes or check engine lights. Tuned engine 2 weeks ago, but problem still persists. Where do I start and what equipment do I need. I am a professional diesel tech, but not so much with gas.
View 3 Replies
My Burb starts right up when the engine compartment is cold. Can barely touch the key and the thing fires right up.
Once engine compartment is hot (operating temp), I shut off the motor, let it sit for a few minutes and I get about 3-5 seconds of dry start each time I start it. It fires right up, runs great after that dry start period.
The dry-start behaves as if it's starved for fuel for those 3-5 seconds.
It's a K1500 with a stock 5.7l (350 ci). 180,000 miles and the entire drivetrain runs like a top. Only mod I've made is a K&N cold air intake.
Here's what I've done/changed recently (i.e. within the past 5k miles):
Fuel pump, OEM installed by dealer.Fuel filter.Ignition control module, BWD.Ignition coil, BWD.Crankshaft position sensor, GM OEM.Engine coolant temp sensor, BWD.Oxygen sensors (all four), GM OEM.Catalytic converter, replaced one of the two.Plug wires, BWD.Plugs, Delco OEM.Distributor cap and rotor, BWD.Cleaned ground connection (bolts to frame) for fuel pump.Alternator, new not reman.PCV valve.Battery.
Full diagnostics by a very qualified shop two weeks ago, no bleedback from injector spider, fuel pressure solid and holds perfectly. After 90 minutes of troubleshooting, the mechanics finally gave up.
One last thing with potential that I can think of is that I started running ethanol-free gas around the same time this issue surfaced. Not at the exact time, but at a relatively similar time. Gas mileage has increased by 40% and power increased, hard to blame "bad gas."
View 19 Replies
I have a 97 2500 454 it dies like you trun the key off, but there is still power to turn the engine over but the truck wont start, and after a couple of tries it will start. It might go for a week and not do it or it might go a couple of miles.
View 4 Replies
I have issues with engine starting when cold outside or after rain. This only happens when engine is cold and has not been started for a day or 2. Distributor cap does not have any condensation inside but does seem to corrode on contact points. Engine turns over fine, has fuel and spark. When this happens engine will not fire and after awhile it will start to fire and lock up when it fires then continue cranking. After repeated attempts it will start and run fine, can be shut off and start right back up with out any issues. It could take a few tries to a few hours of trying before running though. I'm leaning toward a distributor or timing issue. Am I on the right track? 98 Suburban K1500 5.7L ....
View 6 Replies
I replaced the oil pressure switch on an '07 Suburban 5.3L because the oil pressure was showing low once the engine warmed up. That did nothing, then I found out about that little filter/screen under the sensor. I intended to remove and clean the filter then reinstall it. While I was pulling it out, I dropped it back behind the engine and couldn't find it. I checked online and found a few people in other forums that said to just remove the screen as a "fix", so I left it out and put the sensor back in, just to get the vehicle drivable. It started right up and ran fine for me, parked it, and a after sitting for a few hours it started popping while driving with the SES light flashing on the drive home.
Code P0300 was set, no cylinder specific misfire codes were present. I checked the misfire data and cylinder #6 showed tens of thousands of misfires, #5 showed several hundred, but I think it was just picking them up from #6 since #5 is right after #6 in the firing order. I disabled each injector with a scan tool, all changed the idle except #6, it did absolutely nothing. #6 fuel injector had good pulse to it, I connected a fuel pressure gauge and put power/ground to injectors #6 and #4, both dropped the same fuel pressure. I did the "cylinder deactivation" test on the scan tool for the four cylinders that have it, they all did the exact same thing - the engine bogged way down for a couple seconds and then died. Is that normal? I can't say I've ever seen a V8 engine die before when running on 6 or 7 cylinders. I checked compression on cylinder #6, it showed very low, almost zero, but I tried it a few times and it would show just a little compression at times... valves staying shut? I'm thinking when I opened the pressure relief valve on the gauge and the piston was near the bottom of the cylinder may be when it showed some compression. I also switched the coil/wire/plug from #6 to other cylinders and the miss did not follow.
Could having that screen out cause this problem? Having the engine die when deactivating the cylinders makes me wonder if maybe it's commanding all four at the same time, although the test shows each cylinder being controlled separately. Using a MODIS, not a TechII. I just got done putting in a new filter/screen to see if it would make any difference, and of course it didn't.
View 3 Replies
I have here a 2001 3/4 ton Suburban. It arrived last fall with 280K miles and a 6.0L V8 that was on its last leg (low to no oil pressure). I dropped in a 5.3L that I had handy, and had been happily driving it throughout the brutal Minnesota winter.
A couple months ago I noticed an issue developing. After a cold start, the engine would be severely lacking in torque for the first minute or so of driving. You could reach any RPM you wished, but the truck could barely accelerate. Once a minute or so had passed in this fashion, the issue would suddenly disappear... you'd be thrown back in your seat a bit if still attempting to accelerate, and the truck would take off. For the remainder of the trip, things would be fine.
Recently I went to drive the truck after it had sat for some weeks. It started fine, but the issue was now more persistent. When trying to accelerate, the gutlessness would continue for a good 15-20 seconds until finally and suddenly disappearing. Let off the gas, wait a moment, try to accelerate again, and it was the same thing all over again. Eventually I also noticed very obvious stumbling/missing when trying to get moving from a dead stop. Idle remained smooth.
The plugs and wires are only a few months old. The fuel filter is new. I checked for vacuum leaks (none that I could find). Fuel pressure is consistently around 50psi, even while the issue is happening.
The MIL was not on. I checked with my scantool, and found that P0101C was set, with P0101 pending. Visually examined the MAF harness and sensor; all looked fine. Swapped in a used working MAF; no change. (I suspect these codes may be due to the fact that I'm running a 5.3 with a stock, unmodified 6.0 PCM.)
My scantool is a Genisys running System 2.0. I'm by no means an expert with it, but I did know enough to try watching the miss counts while the symptom occurred. All cylinders seemed to be missing equally as much as the others, more or less.
Normally I'd be suspecting the fuel pump and/or associated wiring was going bad, but the pressure seems fine. What I might be missing?
View 10 Replies
2003 Chevy suburban, 115K miles, accelerating I hear a squeal/groan/clicking noise coming from right front of engine. Did not happen this winter, started again in spring. Loses power if stay on accelerator. If let off and then reapply, it will momentarily go away. Appears to be only when air conditioning on. Bad AC or just the pulley?
View 1 Replies
I checked the cables, no corrosion and tight as a drum. I connected an OBD II computer to the plug under the dashboard and the computer replied that there were no trouble codes present. Is OBDII the proper code reader? none of these lights were on before I replaced the battery. now I have constant ABS, flashing Service ride control, change engine oil. The battery has not gone dead as of yet but the ampmeter is charging at about 16.5-17 volts. I disconnected the pos terminal while the vehicle was running and it continued to run even with the lights on.
View 2 Replies
I drive an 05 Chevy Classic (that's an '04 Malibu made in '05), and it's never given me problems (though I've only had it about 2 years). This morning, I can't get it going. The engine turns over when I turn the key (though some of the time it takes several moments), but then as soon as I let go of the key, the engine dies. I tried giving it gas, but this doesn't seem to make a difference. After a couple of tries I noticed that the dashboard lights weren't coming on. They usually all light up while the starter runs, and I can at least get them to light most of the time when the key is turned to "on". None of this works. The power windows will open and close when I have the key turned to on, so the electrical system works somewhat.
View 8 Replies
I just picked up my new 2014 Chevrolet Camaro with the V6 and 6 speed manual transmission. If I just punch the gas pedal when in neutral, the engine almost dies for just a second but then rev's up normally. It seems like a burst of gas chocks out the engine. I have tried the same thing in other Camaro's and the engine rev's up normally as soon as you punch the gas pedal.
View 13 Replies
1991 suburban randomly dies while driving..... I will only have headlights and interior lights.... no other power .....wait 5-10 minutes fires right up.
View 1 Replies
tonight at 1am: I put the key in and turn the ignition, no start, no click, no dashboard warning lights, no nothing. headlights don't turn on at allearlier in the afternoon - didn't check headlights, but no start, no click, no dashboard warning lights. Sliding 1 key into the ignition gave me a somewhat steady buzzing sound from the car, the kind you get to indicate something electrical is happening (I guess that's what it's for.
I wish I were mechanically inclined.) Sliding the other key into the ignition gave me a much more sporadic buzzing sound. Like metal wasn't making contact, when it should. A few hours previous in the morning - car wasn't starting as described above. Someone pushes the car back from the front so we can make way for another car, to come in and give me a jump. I put the car in neutral, and notice that the dashboard lights and buzzer is on, so on a hunch, I try to start the car in neutral and it starts right up. I drive it to the home driveway, no problem.
2 days ago, I bought the car. A 97 nissan sentra. What it could be? Again, never a clicking sound when starting the car to indicate dead battery. I'm familiar with that.
View 16 Replies
I have a 1989 Buick LaSabre that is having some problems and no mechanic seems to be able to figure it out. After 4 computer items totally $1,800.00 since March, the same problem started again yesterday. I am driving through the hills to town and the dashboard lights all come on and my engine cuts out. I stop, put in park and restart and take off again. As soon as I am on the highway, car runs fine. It has something to do with the fuel system I believe because once it cuts out the car smells like lots of gas but after it starts back up (and it does every time) the smell goes away.
View 18 Replies
I have a 1997 88 with 79k. When the engine is warm and my foot is off the gas, the car occasionally dies. I can restart it each time this occurs.
View 4 Replies
