My 2003 MC SS has been acting up, the check engine light starts flashing at me and the car starts shaking when I turn the AC/Heat on. I know nothing about cars and before I take this to a mechanic, what might be the issue, I do not want to go somewhere and get totally ripped off.
View 3 RepliesOk on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesLast night I was driving in my 2003 jetta on the intersate at 65mph with the cruise control on. As I came into a turn I had to tap the brakes. As soon as I did the check engine light came on. The car was doing fine so I drove home from school. Today I drove the car to work which is a five minute drive, and back with no problem. I later went to grab lunch and bring it home and then I noticed the check engine light started flashing. I then felt the engine start to stutter, as if it was misfiring. We had the windshield defrost when we started to smell a rotten egg smell. Luckily we were pulling into our drive when we smelled the odor. I immediately turned off the car and got out. I couldn't smell the rotten egg smell, but I did smell burning plastic. I didn't see any smoke and could not pinpoint the cause of the smell.
View 4 RepliesHere's the deal with this car i just did head gasket, valve job, all new intake gaskets and spark plugs. Car idles fine and mid throttles fine but with high throttle it wont shift and flashes the random misfire light p0300 it seems to run out of power. I've heard everything from maf sensors to ignition coils and wires. i was just wonder a good place to start and good test to do. I have most testing equipment including scan tool so i can ride with it. o and all cylinders compression tested above 150.....
View 13 RepliesI found a steal of a car for my son, a 2003 Monte Carlo SS. The car had been hit slightly in the LF corner. The car needed front brakes, so I bought a package off Ebay that had rotors, pads, and wheel hubs. I replaced the LF wheel hub when we did the brakes and kept one for a spare since the RF felt good.
Shortly after replacing these parts, the car started to make a popping sound when you would turn right. The popping sound is much like an exhaust pipe dragging on the ground. We checked to make sure the was no contact with moving parts. After reading several forums, we decided to replace the LF hub with the spare we had. This did not fix the situation, so we put the first replacement LF hub onto the RF. Still no fix.
After this we decided to take the car to a empty parking lot and drove in circles trying to find the source of the noise. We discovered that the noise would go away if the car was put into neutral. We were still unable to locate the source of the noise.
So I decided to jack the car up and put it in gear and turn right. The noise did not occur with no load on the tires. However the u-joints on the axles were making some excessive noise, so I put in a new set of axles. Again this did not fix the noise. Now thinking the source must be in the differential.
Well two days after putting in new axles, the transmission went out. This will surely fix it, right? Well the mechanic that fixed the transmission said the pump had gone out, and it appeared the differential was creating shavings that caused this situation. GREAT WE FOUND THE SOURCE. Not so much!
Car still makes noise while turning right after replacing the transmission. I have driven myself crazy trying to find the source of this noise including riding in the engine compartment while my father drove in circles in the local high school parking lot.
My 2003 Chevy Imapala went over some large water puddles and shortly after a check engine light came out. My local auto store did a check and stated there is a possible problem with a senor. If the senor got wet, could it even give the computer a good reading? Would it probably give a totally different reading once it dries?
View 4 RepliesWhen cruising my engine randomly has a miss. If I step on it, not necessarily full throttle but some, the engine pulls fine no miss. I don't think it's ignition because it doesn't miss with increased throttle. I have looked at an analyzer and none of the sensors is showing a fault. I have put 20 tankfuls of fuel with cleaner through it after I put a new fuel pump and filter on and I only use Shell now for the last 10 fill ups. The miss is not a passive drop in rpm but more of a buck.
View 5 RepliesI have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 RepliesI've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 RepliesI have a 2007 L.L. Bean Edition Forester. The cruise light is flashing and check engine light is solid. I am well into my retirement age and nearest dealer is about 2 hours away. Is this something that local mechanic can fix? He is very good, but not Subaru schooled. I'm afraid to drive it now.
View 2 RepliesHave a Volvo XC70 and LOVE it! Recently ETS light came on and Check engine has always been on, mechanics did not seem to worried in past. As of the last month seemed to be issue with thermostat... Car would warm to normal when idling and driving below 25 mph... once I accelerated needle would drop and thermostat would go to baseline... Could feel faint warm air, but was only getting cold air coming from vents... Thought it might be thermostat stuck open?
Called my trusted mechanic and he recommended going to a radiator specialist, felt he might not be able to solve. Went to new shop today, after dropping off at 8am when they opened and not hearing from them until 4:45pm, 15 minutes before they close... Car is fixed, or so they say. Hot air is indeed coming out of vents and needle is staying where it should without falling...
BUT, now there is a strange smell (sulfur"ish") coming from the engine, and the car is shuddering and vibrating, bucking almost when car comes to a stop and then accelerates. ETS light is back on and check engine is now flashing!?! Tried going up hill on the way home and could not go faster than 20mph? None of this was happening before I took it in to the new shop today? They changed oil and oil filter and flushed radiater?
Get in my car, try to start it and BAM it hits me. As I turn the key, the engine cranks up quick, kinda too quick, if you ask me. As I go to adjust my radio, I feel my car start to jump around and shake pretty rough. As I look at my gauges, I see my check engine light start to flash. So instead of trying to drive away, I turn it off and try to start it again. Same thing happens!! So I try it again and finally a normal start. Whew, I thought that was close. But oddly enough my check engine light comes on and stays on this time, no more flashing and the engine feels fine. What the problem could be? Is it safe to drive my car?
2000 Buick Park Avenue 3.8 auto....
I have a 2004 Audi A6 wagon that's got 105k miles on it. A couple months ago, the check engine light came on while I was driving it. While it was on, it was flashing and the car felt like it was shuddering, like there was not enough gas getting to the engine. Then the CIL stopped flashing. It happened several times during my short outing that day, but then it never happened again. Now the flashing CIL is back and the car feels the same way when it's happening. I took it to an auto parts store to get the trouble codes read and the guy said P0300 (random cylinder misfire) and P0305 (cylinder 5 misfire) came up.
View 18 RepliesAs the title says, my CEL goes on and flashes too.
I've read up a bit on why the CEL comes on/flash and it says it has something to do with the exhaust system and if continue operating will damage the catalyst converter (which I don't understand since I'm a car dummy.
In addition, the engine vibrates like crazy. I can feel the engine vibrating when I'm inside the car as well.
I already got the car tolled to the dealership and they kinda just told me it might be misfirings and then they said they couldn't locate the problem. So my car basically has to stay there until they open again on Monday and hopefully they will figure out the problem/fix it under the warranty and call me back.
The problem arise late Friday night and I just did a 30K maintenance on Thursday. (but the car already has 43,000 miles on it).
If you get a f!ashing cel ,the next time you start it should it flash right away or can it go back to solid on cell? 02 Accent 1.6 130 k. What can be done to check the flex pipe for a leak? Can you spray water or what? The outside looks good. Also looks hard to check around intake manifold for leaks.
View 11 RepliesYesterday out of no where my rio started to misfire so i immediately took it into autozone to have it checked. when doing so the check engine light was on, but solid.
The tests came back with P0300, P0301, and P0302 or 3. I cant find the papers, but its 3 cyns that are misfiring. The guy at autozone suggested i try changing out the plugs first since its cheaper and has been known to fix this issue.
The second I bought the plugs I went home and changed them out. once finished i started up the car and not only was the car still misfiring, but the check engine light is now flashing... I did notice one thing when changing the plugs.
If facing the engine the second coil from the left had a bit of what looked to be rust. i was able to wipe it off with ease. What my next move should be?
Let me start with some background. 2001 B5.5 Passat Sedan 1.8T 5spd Completely Stock 156,000 miles. So, tonight i head for the grocery store about 5 minutes up the street. I get about half way there, when I notice that the check engine light is flashing. I ease off the gas, and coax it to the next light. At the light, the car feels like it might stall out, and the car seems to shudder, and I notice that the shudder is connected to the RPM of the motor. Meaning, if i rev the motor the shudder gets faster.
I manage to coax the car home to my driveway, and I leave it in a position easy to be towed. So, i figure that I will leave the car running, and look under the hood, but as soon as I open the drivers door, i can smell something burning/smoldering. I shut off the engine, and carefully open the hood. I find no smoke or fire, but I see that the downpipe (or whatever pipe the exhaust coming from the turbo leaves through) is glowing red hot.
I am not sure what happened. The car gave no other obvious symptoms. The other things I should mention though, are that I change my own oil. Always Mobil 1 with a Audi or at least german filter. However, my father was the original owner, and for the first 60k he used conventional oil. The turbo has always been strong, and seemed to deliver full boost. I do not know if it is still boosting in light of recent events.
For the last few weeks, the check engine light has been on and off. My mechanic scanned it a few times, and told me that it was the "Air Injection Pump Code". My understanding is that this system basically divers exhaust gas into the Cat when the car is warming up. If its not working properly, then it is just a emission problem.
I should also mention, that the car has recently been leaking a little bit of water when there is a hard rain storm. On Saturday, I took the rain tray cover off, checked the Pollen Filter, and removed the battery in order to clear out the drain plugs under the battery tray, and the brake master cylinder. As I write this, I begin to wonder if its possible that something just went very wrong with the Air Injection System.
I have a 98 f-150 with a 4.2 and my check engine light is on and when I'm traveling down the road i notice that when i give it gas the engine feels sluggish and my check engine Light is now flashing.
View 6 RepliesMy 2000 deville (which i never drive) but start up and let run decided to give a BIG problem today. I went to charge my a/c up and when I started it it was running very rough... Last week it did it also but after letting it run it smoothed out but today it stayed same and was actually worse. I drove it around the block and check engine light was flashing and car was sputtering like it didn't want to go. Sputtering out of exhaust and exhaust was getting real hot and giving off smoke from behind tires area. it was actually starting to burn my grass. I don't understand why it would do this all of a sudden. I pulled codes and this is what was there
p01571
u1040
u1064
u1192
The only code that is usually in there is the tcc code and its been for years..
Today I was driving and all of a sudden the car started to seem like it wasnt responding well when giving the gas. then the check engine light came on flashing. I pulled over to check in my manual and it says there is a malfunction with the CAT, it started to smell like eggs. now i remember reading once that the smell of eggs is a burnt cat, is this the problem or could it be only the sensor ? How much a new one goes for ? how about the cat, how much does that go for ? if it is my cat how does putting in a high flow cat sound? good or bad ?
View 7 Replies