Chevrolet - Malibu :: 1999 - Hard Clunk When Put Car Into Reverse
Aug 1, 2014
I have a 1999 chevy malibu with a 2005 chevy impala motor in it. Recently I put my car into reverse and it made a hard clunk and went into reverse. Later on that day I tried to go into reverse and it will not reverse. I had to have 3 people push my car back in neutral. However, in neutral I am able to press on the gas and drive forward... This is an automatic transmission. Am I just screwed and need a brand new transmission?
View 12 Replies
Advertisement
My car is idling hard in reverse, and the mechanic said, in fact, a problem with the transmission (a turbine?) Well, a new transmission costs much - so, not much savings there. I was told to try some simple fuel injector cleaner first. Chevy Malibu Classic, 2005....
View 4 Replies
2005 Chevy Malibu
When the driver side door is opened there is a clunk sound about half way through the swing. When the door is closed there is a couple clunks then a thud. The sound is coming from the front of the door.
What is causing this and does it mean big trouble soon?
View 11 Replies
My car will start but die. it either wont turn over or if it does, the engine goes right off. The radio and lights work though. the throttle & iacv were all good. i got it towed and the mechanic brought it in his garage at end of the day. He said it wouldn't start so they left it for monday. The thing is that my ignition sometimes gets stuck and leaves radio & interior lights on. So when they tried starting car on monday, it was dead. They put different battery on & it started right up. they said everything else was ok. they charged my battery & I had no problems. until today, 3 months later, same problem. both times it happen when I am leaving work & both times it was raining & cold. Could my battery be bad? also wonder if place really checked everything out likethey said.
View 5 Replies
I have a 2001 malibu , my cars engine light has been for about a week. This is the second time it has happened. lately I have been having trouble starting my car. Does this have anything to do with my car , or because of the cold weather? How important is it for me to get my car checked out?
View 2 Replies
I have a 2005 Chevy Malibu, automatic transmission. When I put it in reverse and then press the gas pedal, I get a rather loud grinding noise for a couple of seconds. What is causing this, and is it doing any real damage? I have no other problems with the transmission.
View 2 Replies
My 2003 Chevy Malibu recently, out of nowhere, starting idling really hard. It shakes and jumps quite a bit when it idles, much like a car creeps when it's about to run out of gas. It drives fine at speeds over about 10-15 mph, but then when it slows down it gets shaky and bumpy.
View 9 Replies
So a friend of mine has a 01 Passat 1.8 T (Automatic). He is having some reverse issues. It shifts into reverse with a hard clunk then the second you touch the gas it clunks into neutral. The odd part is if you put it in reverse and stay off the gas it will idle back in reverse... But the second you touch the gas nothing. I'm finding it hard to believe the transmission is gone because every other gear is beyond smooth (I mean like brand new car smooth).
View 4 Replies
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 Replies
What are the symptoms of a worn motor or transmission mount? I feel a distinct clunk when I place the car in Drive or Reverse from idle. I did not notice any problem when I bought the car few weeks ago. Before spending 300+ I checked for the problem one more time. The problem is that the clunk was all but gone. An intermittent clunk! What gives? The car is an '05 Malibu w/4cyl, 119k. The former owner had the transmission fluid changed at 94k.
View 1 Replies
My 2005 Impala will have from time to time a hard shift where there is a big clunk_usually 1st gear. I had it at a transmission shop last year and they could not find anything wrong. What is going on.
View 3 Replies
Started having problems with my Chevy Malibu (1999, with 95,000 miles on it) while driving two times this week. Both times an alert warning flashed on my dashboard. The first time, flashed the brake check and ABS warning on the left side of the dashboard, and the second time the check oil and check battery warning on the right side. In both cases, after the warnings flashed, the car was still running, but stepping on the gas pedal resulted in no acceleration, but brakes still worked. The steering wheel also locks-up to the point where I can't turn any more. Both times, I stopped and shut off the engine, waited about 30 seconds and restarted, after which everything is fine and normal. The brake pads were changed recently, but not the rotors which may not be in very good shape.
I took the car to garage and found the belt is good, but I have replaced both the alternator and battery, and also changed the brake pads. Car ran fine for a day. Yesterday while driving, had another issue of the accelerator not working while in the middle of driving. Was going up a small hill, tried to accelerate, but stepping on the accelerator didn't do anything. A few seconds later, I could not press down on the pedal anymore (as if the car was off). Brakes worked, I could turn, and no warning lights. Turned off ignition, restarted the car, and everything was fine. Same problem with the accelerator as I first reported, but no problem with charging or turning the wheel, and no warning lights since the alternator and battery are new.
View 4 Replies
I see it's been 7 months since my daughters last oil change, yet the car has just over 1000 miles since the last oil change. I'm wondering if I should change it for good measure or wait ( it's a 1999 chevy malibu)....
View 19 Replies
It is an automatic. (1999 Malibu) . Is it possible for a car to start but the gear shift to be frozen?
View 5 Replies
I drive a 1999 Chevy Malibu. My car overheated the other day so I pulled over and realized the overflow was bone dry. So I added water and finished my trip. By the time I got there the car was overheating again and the overflow was again empty. I have changed the water pump, the thermostat, and the overflow cap. Whats happening now is when I crank it the car Idles fine until it gets warm, then steam starts to come out of the overflow hose coming from the cap. If I drive it not only steam but all my coolant just starts pouring out of this thing. I was told this might mean a busted head, but there is no coolant in my oil or water coming out of my exhaust.
View 1 Replies
When I tried to turn left yesterday, my car suddenly stopped with both the "check engine" light and "battery" light on, but the heat, headlights and radio were working just fine. I turned off the engine, and waiting a few minutes, ad then restarted the car, and everything is fine. I do not drive the car today. My question: is this a problem with the battery or the electric line? When the "battery" light is on, can i conclude it's a problem limited to the electric line only rather than a fuel line. My car is Chevy Malibu, 1999, with 90,000 mileages on it.
View 12 Replies
I have a 1999 chevy silverado 5.3 4wd w/ tow package. I bough it with 30,000 mi. It has always had a hard shifting/clunk after long drives or sometimes short ones that involve a lot of elevation. Oddly, if I stop and shut the car off for a minute or two the hard shifting stops, but eventually starts again. The truck now has 160,000...still with the shifting issue. What is this and with this many miles is it serious?
View 4 Replies
My issue, just purchased f250, 2004, v 10, manual transmission, state vehicle with 32,000 miles but was a plow vehicle for localRMV lot, that said, great shape and runs strong but I get a clunk and shutter when I am in reverse and only when I push down clutch before stopping. Doesn't do it starting forward or reverse, only reverse and when I push clutch in before stopping. Did have a friend drive and looks like the transfer case is moving, as if mounts or bolts are loose. Does this make sense and could bad slip joints be putting excess torque on ?!?!?
View 4 Replies
Ok so I'm having a problem that seems to have been getting worse. 1999 7.3, auto, 4 door, long bed, 6" lift. When I got the truck a while back I had a slight problem where if I was accelerating hard I would hear a clunk when it shifted into 3rd gear. I'm not hard on the truck that often so it took me a while to realize that the noise was the driveshaft hitting the floorboard right at the joint at the transfer case output.
The carrier bearing was flopping around a bit so I replaced that first. No better... kept driving the truck since it was only a problem while being really hard on it. But it's gotten worse so now when I tow (usually not more than 7-8k lbs) I have a bad vibration on takeoff at low speed. If I try to take off from a stop very hard with any load the driveshaft jumps into the floorboard. So I just replaced the transmission mount and checked the motor mounts, no better. Only thing I can figure at this point is axle wrap...?
View 14 Replies
I continuously read that people with 6.2 F250s averaging 13 mpg or so in a combination city/highway driving. This 2014 4x4 barely has enough power to move itself (honestly, I'd rather have my Ram 1500 back) and barely gets 10mpg. Basically have to give it about half-pedal to even get up to freeway speed and floor it if i want to pass anything. Is it just that much of a POS or does this not sound right? Other than a massive "clunk" sound when shifting from reverse to drive or vice versa, no indication of any problems.
View 14 Replies
Ive got a 04 f350 that after u shift into 4hi or 4lo when u accelerate it it makes loud clunk noise in fwd or reverse hi or lo. With hubs unlocked it still clunks. Have checked, wheel bearings, axle U-joints, and driveshaft joints all good. So I am thinking I've got issues in t-case. Popped drain plug out and wow that dex merc 4 looks nasty. So thinking I need exploded view of transfer case.
View 4 Replies
