Cherokee :: 1995 GC Laredo - AC System Has No Power / Brake Lights And Turn Signals Don't Work
Dec 16, 2013
All of this happened at the same time so has to be related. The a/c system has no power, the brake lights and turn signals don't work, windows wont work, air bag light on. However, the park lights, head lights and hazards work fine. Starts and runs fine. All fuses check out ok. New battery as well.
View 3 Replies
Advertisement
I have a 95 jeep Cherokee and have lost all power to my radio, heater, wipers and turn signals, i have checked all fuses and replace a relay i thought may have been bad, I have yet to find any inline fuses that may cause the issue.
View 1 Replies
I found out last night that all 3 of my brake lights are out. However, my tail lights work, and my turn-signals work. So obviously its not a big wiring deal. I was looking for the brake switch but i don't know where its at because i looked underneath. What fuse is the brake lights cause my manual doesn't have it listed. I drive a 04 Elantra GLS.
View 6 Replies
I've got a 98 Silverado. Break lights and rear turn signals won't work but tail lights and reverse lights work. Also the brake light on the cab does work.
View 6 Replies
So I lent my santa fe to a buddy to do some hauling, I got it back yesterday and the turn signals and the brake lights don't work...notta. Regular running lights are working without issue, but no turn signals, no hazards, no brakes. Even the "tick, tick, tick" of the turn signal is gone, it's just dead.
View 1 Replies
This has been driving nuts for 2 days.... Brake lights dont work. Either pushing pedal or turning on lights. Turn signals work just fine.
Cab/cargo/3rd brake light on back of cab doesn't work either. I have checked/done the following:
- Checked Brake pedal switch for continuity. Tested fine.
- put multi meter on wiring all the way back to brake lights. No drop in voltage.
- changed bulbs. #3157 dual filament.
- positioned steering wheel all the way up and all the way down as suggested on here. No change.
- checked multi function switch (turn signal switch) for wiring issues. None found.
- kicked rear quarter panel for caveman adjustment out of frustration. No change.
What am I missing?
View 9 Replies
I have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 Replies
I have a 1995 Ford f250 Powerstroke and i do not have turn signals, rear running lights, brake lights or reverse lights. i checked the fuses and they seem to be good but i dont want to tear everything out to check the harness if it could be a bad ground. any insight?
View 1 Replies
I just bought an 05 F250 XLT. I noticed tonight that the rear turn signals and brake lights don't work.
The front turn signals work fine, although they flash fast. I know that usually means a light on its way out. neither taillight flashes though, which puzzles me.
My second issue is that, of the 3 brake lights, only the high mounted light illuminates when I hit the brakes.
View 1 Replies
My sons 2006 F350 brake lights and rear turn signals quit working. When the headlights are on, all the lights operate but the rear turn signals and brake lights do not nor do the emergency flashers. The front signals work but flash very rapidly. Although I'm not an auto electrician, I'm fairly mechanically inclined but the fact that the front signals work, the rear don't and all lights work as lights, just not as turn signals or brake lights.
View 4 Replies
Every time I step on the brakes, there is a bright spark in fuse #13. My brake lights, turn signals and hazards don't work. At this point my truck isn't drivable.
According to the owner's manual in my truck, says circuit #13 is for "stop lamps, CHMSL/hazard, trailer tow stop lamp, and speed control."
I'm assuming that the hazard part covers the turn signals as well, but I know the cruise control works even when the fuse is blown. I used it last night on the way home (this was before I realized I didn't have brake lights).
So I know I have a short somewhere. The only mods I've done to the lights are aftermarket headlights, but if the fuse only gets blown when I step on the brakes, I don't see what that would have to do with it. Also, the lights have been installed and working for about a month before this started. The only thing that I did around the same time was install the gauges. I ran the power to them from #5, the customer access circuit.
Are there any other "common" areas for this to happen? I already removed the rear brake lights and it didn't work. I am quickly running out of 20A mini fuses.
View 9 Replies
I have a 96 grand Cherokee Laredo, and the other day it just wouldn't start. The jeep will not turn over, so i started checking some things out and determined that it was not getting a spark. Since i replaced the distributor cap recently i figured it had to be the ignition coil, so i replaced that. Still no go, i tested to see if the ignition coil was getting a spark by using an ohm meter, and nothing.
So something is preventing the spark even getting that far. I do not know much about vehicles, and i have to think it is something in the electrical system (like a chip or something),possibly security system, or NSS.
View 1 Replies
I was turning left in my 01 Excursion and I think I hit the turn signal while doing so and tripped something. Now I have no turn signals and no brake lights. Headlights and tail lights work fine. I checked a couple of fuses under the hood that I believe are for turn signals, according to my manual they are fuses #20 and 22. They aren't getting any power, but the fuses themselves are fine. Is there another fuse somewhere to check? Or something else entirely?
View 12 Replies
2000 jeep cherokee brake lights will not work.changed the bulbs, brake switch, checked fuses, ripped the effin panels out and checked wires and grounds, ripped up rugs found the mouse nest-no mouse, no chews in wires. the parking lights work, hazard lights work? WHEN LIGHTS ARE ON, RT HAND BLINKER DOESN'T WORK...WHEN LIGHTS ARE OFF BOTH BLINKERS WORK..
View 1 Replies
My service advancetrac light comes on about once a month, seems random but when it does the turn signals will not work, you have to hold indicator in place for signals to work-not to safe. My local dealer has not been able to fix issue...
View 3 Replies
I'm having problems with my front marker lights. The turn signals work but when I turn on the parking lights or headlights they don't work. They only work with the turn signals. And I can't get the front side marker lights to come on. I've tried everything...
View 2 Replies
I recently bought a 07 Expedition with light left front damage. After the repair I noticed that I'm not getting any power to the rear turn/brake, and backup lamps.The tail lamps and third break light work as does the trailer plug. I know that they were working prior to repairing the front. I did disconnect an aftermarket alarm during the repair. Basically all I replace was L/F sheet metal. Of cause I checked the obvious things like fuses and current to the tail light sockets.
View 6 Replies
I have a 2007 F150 that it's brake lights and turn signals have gone out. What's wrong? I've checked fuses and connections.
View 1 Replies
I was using a 2004 Heritage F150 and when I connected a trailer to it something got fried. I lost both my turn signals and brake lights. The trailer worked fine on my friends truck so I don't think the issue was there but with the 4-pin round connector that was on the truck.
I found two 10A fuses blown under the hood and replaced them but that didn't work. They were in slots 19 and 20 and are listed as the camper/trailer adapter fuses. The running lights still work. The interior turn signal arrows don't even light up or anything when the turn signal is activated.
View 2 Replies
I have a 2003 Ford F150 King Ranch which I just bought, I noticed that the turn signals (both right and left) do not work and also the power mirrors are not working.
My 2003 Ford F150 has the 5.4 vortec, 4 x 4, automatic with 200K on it
View 5 Replies
Well, on our way home during my leave, the wife made the comment about halfway home that the blinkers had quit working. I assumed it was probably a fuse or relay, so we came on home. I have been looking at it for a few days now (too hot to spend too much time out crawling around under the dash ) and I am still having some trouble. My brake lights, and hazards are not working, and neither is the cruise, which was working fine while I drove before the blinkers went out.
I have no power at all to the flasher relay. I replaced the brake light switch because it was definitely worn and looked a little burned inside when I pulled it out and inspected, but still nothing. Have not found any fuses blown. Brake pressure switch fused link harness seems good with my test light. Wipers, brights, everything else on the turn signal switch works fine. Can't even get the cruise to go into diagnostic mode, it only blinks once when I try.
View 5 Replies