Celica :: 2004 1zz-fe - Code P0300 / Rough Idle And Stumble At Low Rpms
Apr 3, 2012
I have a 100% stock 2004 Celica GT ~125,000 miles. Over the last few months I have been getting a rough idle and stumble at low rpms. The other day the car would not restart after sitting for about 20 minutes. Only recently has it actually thrown a DTC. The error codes were for misfires (P0300, P0301,P0302,P0303, P0304). I don’t get a code every time but the problem seems to be more noticeable if the car has been ran for a while, sits for 20-30 minutes while in a store and then when I try to start it when I come out of the store is when the problem most often occurs. When it restarts it will stumble at low RPM and if I hit the gas it has little response and misses badly. I have never used a scanner until now. I am using a Autel MS509 scanner and I am not sure it is giving me the correct diagnostic numbers for the live data. I think the DTC are correct but the live data is questionable.
Here is what I have done so far.
- Cleaned IAC valve (completely removed and cleaned)
- Searched for vacuum leaks using carb cleaner
- Cleaned MAF sensor
- Replaced all 4 injectors
- Replaced upstream and downstream O2 sensors
- Replaced Coolant Temp Sensor
- Ensured cam tensioner is providing adequate pressure to the cam chain
- Tried 2 sets of new Iridium NGK plugs and a new set of Bosch Copper plugs
- Moved coil packs around
- New air filter
- New fuel filter
- SeaFoam through intake and gas tank. I have not mixed in the oil.
- Compression Test (1=190,2=190,3=160,4=178)
Things I have not done.
- Taken it to the stealership
- Fuel pressure test
- Valve Clearance
I am concerned about the compression test because according to the service manual it should be around 218. I was using a Harbor Freight compression tester and I am not 100% sure I had a good seal with the tester.
View 14 Replies
Advertisement
Just did the timing chain, phasers, oil pump and lash adjusters on my 05 5.4 s-crew. Always had a bit of a rough idle but now it's worse. If the truck idles for an extended period it sets a p0300. Just off idle the misfire is gone. It does seem a touch down on power but otherwise runs great. I did have the plugs out during the work. I cleaned them, applied anti seize and re installed. The previous owner had the plugs and COPs changed 10k miles ago. Plugs are motorcraft and coils are aftermarket.
I monitored with oreillys crappy scan tool and the miss only happens at idle. It is not a dead miss; unplugging COP on each cylinder still makes it worse.
Truck idles warm at like 570 rpm and if I hold my foot on the pedal to raise rpm a bit miss goes away.
Each cylinder is logging misfire counts with no rhyme or reason. The only thing odd during the timing job was 4 spark plugs were partially loose.
I'm sure the timing is correct; I used the OTC crank tool and for timing kit. Truck has 150k, front 02s are fairly new...
View 4 Replies
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 Replies
97 chevy k1500 with 305, engine rebuilt by shop 60k ago, last few months only drove truck 4-5 times, last time driving gave p0306, new plugs, wires, cap, rotor, cleared code, now gives p0300, took intake apart removed spider, sprayed/scrubbed each injector and poppet with cleaner, but no way of cleaning the line between the injector and poppets. No change after cleaning. Also ran injector cleaner through tank. All vacuum hoses look in good order, sprayed carb cleaner around intake to check for leaks at intake/throttle body, no leaks.
Checked TPS, IAC, MAF, Coil and fuel pressure, all good except fuel pressure was 52-54 while idle, replaced fuel pump, screen filter and main filter, cleared code, rough start and rough idle still gives p0300. Checked coil with ohmmeter, between posts A & C, Chilton says 0.1 ohms, i got 0.5 ohms, went to autozone and had them check a new coil, it have 0.5 ohms......? Can drive at higher speeds and runs smooth, but idle is poor almost dies.Checked fuel pressure after pump replacement, still ~54 psi. Stumped and don't want to throw more parts at it without a proper diagnosis. Have a OBDII pocket scan tool, but can't find manual, will try to find manual and see if I can pinpoint the misfiring cylinders.
View 7 Replies
Just bought a 2.0l 2001 golf four door. the previous owner had the car for only a short time. They claimed the CEL came on and the code was for the MAF. He cleaned it and when I test drove the car there was no light or sign of any issues with how the car ran. Today while figuring out why the alarm kept going off(battery died in key fob and i replaced them), it began idling rough. It had just started to rain as well. From what i could find from older thread is it could still be the MAF, TCV/ISV, or O2 sensor. Is there any good way to diagnose without a vag-com cable. Mine wont update its firmware and i'm screwed at the moment in terms of gathering info on the problem.
View 9 Replies
I have a 2000 Suburban 4wd that has a p0300 code. The misfires are coming mainly from #2 and #7 cylinders. Misfires only occur at idle. over 1500 rpm the misfires disappear. I have put new A/C Iridium plugs in, new wires, and new coil packs on both cylinders but the problem is not any better. All 8 fuel injectors all go to 55 psi when activated and drop to 28 when released. All tests were done with my Snap-On Solus.
View 2 Replies
1987 Ranger and the computer will not communicate. I'm trying to check for codes because of a rough idle and stumble when starting out from a stop. Check engine works but won't flash when using a jumper across the data link. Used a OTC scanner but it only times out and comes up "no data". Where to go from here?
View 7 Replies
I bought an 04 f150 super crew cab with the 5.4L triton in it 3 years ago with 50k on it from my great uncle who was the original owner. It's had a tick to it since he had it but the dealership told him they couldn't find anything wrong with it and to get use to the noise. It's ran pretty good up until last couple months where it's been running really rough and not doing the best. It's still hasn't been all the time but more intermittent and comes and goes, but when it's running bad the rpm drops down to about 200 and my motor sounds blown.
When that's happening I could put in neutral and rev it up and it would go back to normal for a bit, but now it's all the time and stalls out even at 70 on the hwy. The codes it throws are, p1000- monitor checks not complete-more driving required, p0345- camshaft pos sens circ error(bank 2), p0022- A camshaft pos timing-over retarded bank 2. Things I have tried-changed all 8 plugs, added K&N air intake, replaced both cam sensors, replaced fuel pump driver module (due to corrosion). Tonight I'm going to clean the throttle body, mas air flow sensor, change fuel filter.
View 14 Replies
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 Replies
2003 F150 5.4 72852 miles
I have a Rough Idle & sometimes a hesitation or stumble on acceleration. I cleaned the MAF & IAC motor & Air & Fuel Filters are new. I got a 20890 scanner & ran test 6 53 as suggested in many posts by BlueGrass. Here are My results & what They Convert to.
1 00F5 .3675
2 0051 .1215
3 0000
4 0000
5 00A3 .2445
6 0000
7 0000
8 0000
I'm guessing the cop's are ok & probably need plugs? I was hoping to just swap a coil. Too cold to do plugs & truck won't fit in my garage.
View 3 Replies
I have a 2000 Celica GTS that idles a little rough it has 118000 miles on it.. Fluctuates between 500 rpm and about 1100 rpm. Doesnt always do this, usually after ive been driving for a while. I also may have a rod knock, what parts would i need to fix both of these issues? Me and some friends can do the work ourselves, i just need the parts.
View 1 Replies
What could cause this? I have 100k and I only notice this if in park or neutral at 1500rpms. It goes away before and after and it seems to drive very smoothly. I had a bad alternator and I just replaced it but the "new" one is making a high pitching ringing so I'm having the shop change that out for a new oem. Any chance it's the alternator or could this be something else. I have sea foamed the throttle body recently and cleaned the maf recently and changed the air filter. I didn't do plugs but they are do at 120k
View 7 Replies
I have a 1987 Convertible Celica GT, with Manual Transmission. The car will not idle at lower RPM. I had someone look at it, and they have it where it will idle at 2000 RPM, but anything lower than that, and the engine will die when not giving it gas.
The engine accelerates great and runs great at any speed, but if you push in the clutch without giving it gas, it will die, unless the idle speed is cranked up like it is now. What this might be?
View 4 Replies
I have had some slight rough running with a cold engine and stumble <2000rpm. Finally it tripped a CEL which was read as a misfire code.
The mechanic swapped the coil and plug(recent) and no change. He did a compression test and air blew out the exhaust. So.......the car needs a valve job which entails motor removal and fixing the head and reinstall. He rough estimates this at $2000 and rate is $65/hr.
He mentioned looking at pistons and may be a bit more if rough.
This car well maintained (170,000 miles 2005 Legacy turbo wagon with manual)...
View 19 Replies
I have a 2000 Toyota Avalon XLS with 134k miles, engine is a v6 (3.0). It has a rough idle and a steady misfire. You can drive it sometimes and it will run perfect and you can drive it sometimes and it will misfire. I am getting codes P1150, P0300,P0302, P0304,P0306. Driving me nuts.
View 1 Replies
So I just drove my 85 to san francisco and back to Los Angles this weekend to visit my girlfriend and i had high oil pressure all the way until i blew my valve cover gasket.
So i fixed it finally today and it ran fine for a couple blocks and then my rpms shot up to about 3000 rpm and wont come down at idle speed and the car wants to keep going while in drive.
Its a 2.4l 22re EFI
View 2 Replies
I just got a 87 celica for $500. Anyway it runs at 2000 rpm's for an idle, could a valve adjustment be a possible problem? Also where is the best place to find some performance parts for this thing? Would like cams, headers, pistons......?
View 6 Replies
I have a 2004 SD with 5.4 that is running pretty rough both at idle and driving. Truck shakes a lot at lower rpms. I have a scan tool and had a misfire on cylinder 4 so I replaced the coil and the plug. Also replaced the idle air control valve. Plan on replacing O2 B1 S2. (One of my codes) even after replacing the coil and plug I'm still getting misfire detected from cylinder 4??? Other codes I had were misfire detected on he first 1000 revolutions. That hasn't come back though.
View 2 Replies
My brother-in-law brought me his 2004 Trailblazer that had an extremely rough idle and would die if ya thought about the air conditioner and all! So he had replaced the cam sensor, didn't work. He replaced the spark plugs didn't work. He replaced the fuel filter didn't work. So he asked me about it and ran across a fella talking about the CAM ACTUATOR SOLENOID and explained all about what to look for and such and low and behold new solenoid later purrs like a new one!!! It is look right above the power steering pump there is a plug in the side of the engine there with electric wires running to it.
One of the signs of being bad is oil inside that 2 wire plug just pull it off and look in it. Now to remove it you will have to take the power steering pump loose so it will move back out of the way so you can pull the solenoid out of the engine if ya get it out look on the end there are grooves running around it with little screens on them see if any are gone or coming apart, this usually sets a P0016 code which is stuff interfering with the sensors inside. If there is any oil in the plug or any screens missing then it will have to be replaced.
View 14 Replies
I have a 2005 f150 5.4 3 valve with the p0012 code the truck runs good has a rough idle not sure if it is worth changing the vct or not the truck has 190000 miles....
View 1 Replies
So I bought a 2006 F150 stx reg cab with the 4.6l motor with 90k miles on it a few weeks ago. It was in really good condition and I couldn't pass the deal up. All in all, I love this truck. However at idle the truck is a bit rough. No check engine light, but a bit rough non the less. So I hooked up my obd2 torque app and I see I have anywhere between 6 and 60 total counted misfires, but none detected by individual cylinder. So I ran a scan and have a B1360 code without the CEL on. So I changed the plugs and coil packs and cleaned the k&n filer (non cold air filter, just a replacement k&n) and I still have all the symptoms and the b136p code. So I Google the b1360 code and there's very little on it. Basically says open circuit ignition.
View 1 Replies
