Celica :: 1994 Toyota GT 2.2L Automatic - Rough Idle When Fully Warmed Up
Apr 25, 2011
The car: 1994 toyota celica GT 2.2L automatic
Here's the problem: car starts fine when cold. When fully warmed up, if i stop to go to the store or something, and then start it after like 20 - 30 minutes it will start and the idle will be fluctuating between 800 and 400 for a few minutes and then even out. sometimes it will actually start up and die immediately, in which case i can save it by giving it gas for a few seconds and then it's fine.
What I've done so far: plugs (NGK), wires, cap, rotor, fuel filter (toyota), (checked air filter. still clean), tried cleaning the throttle body and IAC with some deep creep spray while on the car (not much effect).
View 14 Replies
Advertisement
I have a 1993 Geo Prizm (Toyota Corolla) that idles roughly and lopes only when the engine is fully warmed up to operating temp. I changed the plugs, and wires are only 1 year old and seem to be in good shape. I suspected a vacuum leak, but have not been able to find one.
View 4 Replies
I just bought a 92 Toyota Celica for something to play around with. It's got just over 200,000 miles and everything seems to run alright except there is a really rough vibration at idle. The vibration is so bad that it's almost visible. You can still feel the vibration in drive but it isn't nearly as bad.
Any clue at what could be causing the vibration? I'll try to get a sound clip or video uploaded ....
View 5 Replies
My 94 Toyota Pickup is having a strange intermittent issue. Engine will run hot, like the thermostat is stuck periodically. Does not overheat, just runs much closer to the red than usual. Again this only happens sometimes. It is worth noting that it is winter here in Northern Sonoma County, CA, so it may actually get into the red if I were driving around in the summer. I have also not taken it on trips over 30 miles when it was doing this.
When this problem occurs (e.g. the engine has been running hot) and I shut the truck off and say run into the store, then come back to a heat soaked engine it idles very rough when started (like it's missing on one cylinder). Once I put it in gear and start driving the idle smooths out and I have no problems. Problem has been going on for about a week.
Sticking thermostat seems obvious but that does not explain the rough idle on start up. Or does it. If so why?
View 11 Replies
I have a 1999 Dodge Ram 1500, 5.9L. My problem is it will not idle until the engine is fully warmed up. When I first start it, I need to keep my foot on the gas, if I let it go it dies.
View 1 Replies
I have a 2001 Toyota celica GT auto. It has 120k miles. I seem to have an issue that really is not causing a problem except for annoyance. After coming to a stop the car seems to exhibit the signs of stalling (car idles rough, shakes a bit) however the car never stalls. Once I start driving all is well. Now I took it to the dealer and they replaced the Idle Air Control Valve which is under the throttle body. They said it was getting stuck and due to the higher mileage possible. It was replaced and the problem is still there. The funny thing is even though the car exhibits these stalling symptoms the idle does not drop below 500 rpm (both dealer and I have verified this).
View 3 Replies
I have a '93 Toyota Celica Standard transmission. Recently it's been lagging in power. Only happens after it's warmed up. I'll be driving along and it just seems to lose power. Have to stomp on the gas to get it to kick in. Also, at the same time, when stopped it idles really low. Cold, no problem. Took it to Toyota dealer to have it diagnosed. I Stated that it might be the MAF sensor. They checked it out and said it needed a major tune up (to the tune of $700!) Now, I know it needs a tune up, but the symptoms don't seem to correlate to that being the problem. I asked about the MAF sensor and they said no diagnostic codes came up. Is it possible the air filter is clogged? Can the sensor malfunction intermittently?
View 14 Replies
2005 F250 6.0L ... My truck is running really rough when the engine isn't all the way quite warmed up. once the truck is fully warmed up to normal running temp it runs good. I am getting four engine codes. P0672, P0673, P0674, P0676 These codes say 2,3,4, and 6 glow plugs have a open circuit. Can this be the cause of my problem?
View 7 Replies
83' Toyota Celica GT with an automatic transmission. The problem that we are having is that we can't get it to turn over. All it wants to do is click at us. As far as we both can tell all cables and wiring harnesses are plugged in and there aren't any loose wires. We've had the alternator and starter checked and they both passed. Also there is a new battery with new terminals installed so that's not going to be the problem. In all of the reading that I've done I keep hearing about a neutral start switch. What is it? And where is it located? I believe I've found a spot where it should be but there isn't anything there. And we've put all of the parts in the car back where they go.
View 4 Replies
My son has a 1994 Celica GT with the 2.2 5S-FE engine. Recently told me his heat didn't work very well, he had mentioned it last year but due to extreme cold we've been having I decided I would look at it for him. So anyway, I started by pulling the thermostat thinking it was probably stuck open or possibly someone had removed it completely, well there was one in there and it was closed so I tested it in boiling water, worked fine, replaced it anyway.
So then I checked behind and under the dash, thinking maybe something was opening or closing completely, but they are connected and operating, when I move the controls inside I can hear the doors moving and closing and all the linkages under the dash are connected and operating. Still no heat, so I figured the heater core was clogged since the return hose didn't seem to be getting hot, or the heater control valve was bad, pulled the heater core hoses, checked the heater control valve, control valve worked fine and was not plugged. Flushed the heater core, nice clean antifreeze, I then checked it with air, manual said put 6 psi on the input and make sure it was coming out of the return, which it was.
Reconnected everything, bled the air, still nothing, took the hoses off and connected the return hose to the heater control valve, bypassing the heater core, both hoses got hot. Sure seemed like a clogged heater core, did the air test again with 2 psi, still made its way out the return side. Reconnected everything again, still same issue, return hose never got hot. So while it was running hot with thermostat open, I removed the return hose, nothing coming out of the core, then I revved the engine and it started coming out, reconnected it and ran car at 3000 RPM, finally a little heat out of the vent, about 115 degrees by thermometer placed in vent, as soon as I let it idle the temp fell back to 80 within a minute or so.
Now I figured the water pump impeller was worn/corroded or was slipping on the shaft, so I pulled the whole thing apart. ( I should mention that the entire cooling system is very clean I don't see any corrosion anywhere) Any of you that have done this knows what a pain in the butt the whole job is, anyway, when I got it apart I was surprised to see that the impeller looked like new and was definitely NOT slipping on the shaft... what the heck???
When I took the pump off the housing I noticed the housing had a lot of wear, it look as if the previous owner let the water pump fail to the point that the bearing wore enough that the impeller ground down the raised boss inside the housing, I though AH-HA, this has got to be the problem, water is not actually pumping/circulating inside the pump as efficiently as it should, hence the reason I only get coolant into the heater core at high RPM. So i replaced the housing, the water pump, and while I was in there I did all the oil seals, and the timing belt. Well I got it all back together, fired it up added coolant, let the engine come up to temp, bled air, still NO HEAT!
View 8 Replies
I have a 94 gt with the 5sfe and at idle with the a/c on and up to operating temp the idle goes from 750 to 500 and cycles like that. It sounds like it is when the a/c compressor is cycling on and off but the compressor never disconnects the clutch unless I turn the a/c off. also when it drops in rpm the engine shakes bad. I have checked all the motor mounts and all are good and the rear one has a solid mount insert.
View 1 Replies
I took my 2001 Toyota Celica GT in to have the engine re-built due to a connecting rod that was ready to blow. I have taken it back to them four times. First time not dropping into 4th gear car is automatic stays stuck at 3RPMs. Said it was a transmission problem. I said didn't have one when I came in and not having one on my way out.
Nothing wrong with transmission. Said they fixed whatever they came up with and still car not dropping into 4th gear and my hood shakes so bad I have to put it in neutral to stop the shaking/vibrating at every stop sign and red light. Said they changed out the non-detergent oil for thirty weight and the shaking stopped for a minute.
I told them the third time I brought it back that the hood was still shaking, still not dropping into 4th gear. I checked my oil and fluids a day later and found no oil in my car and the tip of my dip stick was black. No coolant in the car either. I told them that this car needs special spark plugs or it will run like it needs a tuneup with no power. I was pissed.
They said that I had two broken motor mounts and the engine wasn't sitting correctly and that is what was causing the the shake and the 4th gear from dropping down. I was astounded..... They replaced the motor mounts and the spark plugs. When I drove it home it drove great. I even took it out to the river to make sure it was running great because I am selling this car and they knew I was selling it.
My buyer took it to Toyota of Orange and had a test done on the car to the tune of $120.00. It came back with upper and lower power steering hoses leaking and that I needed a new power steering pump. And wait for it.... a new head gasket!!!!
Which tells me they never rebuilt my engine, they just fixed the connecting rod. I took the report into them from Toyota and told them that I want everything fixed on this report and I want my car back in three days or I will take you to court.
I talked to the owner today to ask him when my car would be ready and he said by tonight that he had replaced the head gasket. Which still doesn't tell me if they rebuilt the whole engine. I told him I wanted the power steering pump and hoses fixed as well or I would report them to the Bureau of Automotive Repair. With the engine vibrating and jumping all over the place couldn't that have caused the power steering pump and hoses to be damaged? And am I within my rights to make them fix these at no charge as well?
View 4 Replies
My 94 gt doesn't have the idle speed adjustment screw like the manual says it should so how does one adjust the idle speed?
View 7 Replies
I have a 2004 gls 1.8t Jetta. It has a straight piped turbo back exhaust, and a stage 2 tune. I recently had a problem with my car starting to rough idle when the engine gets to proper temp. The car starts to idle roughly, and when driving the car will bog down, if I keep my foot on the gas, the car acts like it is coasting and the rpms fall, but at some point the car will shoot off like i floored it. At lower rpms in the 1st and second gear, the car will randomly and periodically start bucking, with the same symptoms. I already replaced my coil packs and spark plugs with a kit off ecs, and when i went to change the spark plugs i had oil on the spark plugs and oil leaking from a bad valve cover gasket, so that was replaced as well. I replaced the fuel filter already.
The MAF sensor was just cleaned and didn't look too dirty. When I unplug the MAF it still idles rough. The fuel pump relay can be heard working properly when the door opens. Another problem that sometimes occurs on cold start is if I don't wait long enough for the pump to activate or sometime right after it starts, the car will start partly then stall out. When driving and the car is bucking the exhaust gives rich fuel smell. Also when 2 stepping in the car (which I don't do very often), the CEL starts to blink and the car misfires and drives rough. I figure since I don't have many parts on it yet I probably shouldn't do it anyway so I don't blow up the engine.
View 3 Replies
I am new to the v10 I only ever owned 7.3 this is my father truck it's a 99 with 200k on it. The problem is it will idle fine when cold but when it is warned up very ruff idle no codes and when I go back at the end of this week I will check the O2 sensor with AE but I really don't know much about it.
View 2 Replies
Have a heavy steering feel on their 2010's with the 215 45/17 tires? It seems much heavier than previous Prius's and also have noticed that mine when it is really cold the steering wheel gets a little twitchy until it is fully warmed up.
View 12 Replies
I recently bought a 1992 Celica GT with 250k miles on it. It has a rough idle and a couple other things that may or may not be stemming from the same thing that's causing the rough idle
Like I said, it has a rough idle and there is a bit of jerking sometimes during acceleration. The exhaust makes sort of a "put-put-put" or "chirping" sound at lower RPMs and the frequency of the sound corresponds to the engine RPM. I do know of a couple things that could be causing the rough idle and maybe even the jerking, but I'm not sure about the sound from the exhaust.
The cooling fans are hard wired to the ignition so they run constantly, so when it's cold out like it is right now it takes forever for the engine to warm up. Is there a switch somewhere that they are supposed to be wired through? Where would that be? Also, the previous owner did kind of a hack job of putting on a cold air intake and I think I may be missing some sensors, especially because it seems to burn more fuel than it should. What sensors are located on the air intake, or are there even some in the stock airbox itself? And would this possibly be contributing to the rough idle and the jerking?
Also, I do get some vibrations when stopped at idle so I think I may want to replace the motor mounts.
View 14 Replies
About a week and a half ago I took my 2008 ISF to Lexus to have them check out the ticking noise. My car has 63K miles on it and I notice the ticking noise after it is fully warmed up. I normally have just been driving it in Sport-Manual too. The sound seems to come from the driver's side fender well area and I hear it best when it is in drive in my garage or at a drive thru.
At first Lexus couldn't duplicate the sound even after driving the car. So I went to the dealership and drove the car about 10 mins for them to hear. The service advisor and a technician heard it this time. They had to call the regional Field Technical Service rep for direction on how to proceed. The FTS person recommend swapping the driver's side high pressure fuel pump to the passenger side to see if the noise followed the pump. I guess they've had problems in the past with the high pressure pumps on the LS models. I again went down to the dealer to drive the car and the noise stayed on the driver's side.
View 14 Replies
I have a 1991 Celica GT. 175K miles. The car recently developed an issue where it jerks back and forth at light throttle, sort of like a newbie trying to learn to drive a stick. It happens at pretty much any speed, but is less pronounced at the higher speeds (45 MPH). In addition, it will not idle at a constant speed and cycles between 1100 rpm and about 300... or kill.
I've taken the throttle body off and IAC valve off and cleaned them both but it didn't change the behavior. If I pinch the line to the MAP sensor, the idle straightens out at about 1100 rpm. Disconnecting the MAP sensor gives good idle, but no performance while driving, so not a solution.
Things I haven't done yet: check continuity on throttle position sensor, checked MAP sensor (how?).
View 2 Replies
3.5 has engine knock coming from oil pan, gets louder when engine fully warmed up. Suspect connecting rod bearings. 99 Intrigue has 203K on it and otherwise in excellant condition. Is it possible to replace connecting rod bearings with engine in car. What is involved in removing lower crankcase after oil pan is removed. Car has been trouble free so far and would like to get another 60K out of it
View 5 Replies
When car is fully warmed up, I notice in Sport+ (manual mode) when accelerating in 2nd gear right around 2000-2200RPMs, I get a slipping/hesitation before it corrects itself and is fine. Mostly with slow acceleration...fast acceleration doesn't really trigger this.
Also when decelerating and coming to slow stop, sometimes it jams/jams into first gear on its own. Doesn't happen all the time but sometimes.
Overall, I still like the tranny and finding which mode works best in which situation like bumper2bumper traffic, light traffic, slow driving, etc...
View 14 Replies
