Celica :: 1991 GT Cranks But No Start - Blinking Engine Light / Code 12
Jul 12, 2015
My cousins car died. cranks but NO start. It was not very well taken care of, but it is her daily driver. Threw a code 12, which is SOMETHING with the ignition.
Have replaced the...
distributer/cap/rotor
spark plugs
wires
ignition coil
valve cover gasket [unrelated HUGE oil leak]
100a ALT fuse
Timing is correct as far as i can tell, 12 volts at both wires for the ignition coil
Battery is good, alt is good...
View 1 Replies
Advertisement
I have a stock 1994 Celica GT with the 5sfe M/T .... I do have a headgasket leaking, and I am having another motor rebuilt and put in next month. I just need to nurse this one along for now. Right now it cranks but will not start. does not even fire up at all.
Code 12 - so I got another dizzy from the salvage yard, the pickup coils ohm out like they should as does the ignition coil. and I bought a brand new condenser for it as the old one tested bad. and when I first got the dizzy i put it in and it fired right up and ran for a couple days, then began doing it again. I went back to the salvage yard and grabbed another one that tested good, and when I put it in it fired up the first time but then shut off and has not started since.
But is it possible for the distributor to still be the problem even though the coils test ok? the shaft doesn't have any play in it, and the air gaps are within spec. I can barely get a .2mm between them. I also grabbed a couple of igniters while I was there. When I get it to run it may die when its cold and give me a code 14.
So from there I'm down to testing the distributor circuit, and the starter signal circuit, and the ECU. What is the best way to go about testing this to be Certain of what I need to go buy instead of just replacing stuff.
View 3 Replies
Have a 91 Aerostar that won't start. Has fuel pressure, pulse to fuel injectors, strong spark, strong compression, etc.
Thinking that the spark may be coming at the wrong time I tried a spare ignition module that I keep. No luck. Since my distributor had a lifetime warranty I got another one, again, thinking spark was coming at wrong time. Nothing. Engine won't even pop.
I am going to drop the front pipe in the unlikely even that the new converter is plugged or, somewhat more likely, the muffler, but I am leaning toward a computer at this point.. Still don't understand since it is getting spark and gas why engine won't even pop.
View 14 Replies
I have a 1991 celica that I can not get to start. The car has the 3sfe 2.0 in it that I think came out of an 89 celica. We have put a new starter on this car, alternator, plugs, wires and distributor cap, battery and more onto this car. The car however will push start. When you turn the key everything comes on and it clicks. Nothing else happens.
View 7 Replies
Its a 1991 Toyota celica with the 1.6 and 5 speed trans. the motor on cold or hot start up shakes really bad and has a lot of valve chatter. Along with that, the motor does not want to rev at all, almost like you are not even touching the gas, but you have it to the floor. A little back ground on the car is, the car sat for 6 months and i bought it from a friend to drive back and forth to work to keep miles of my supra. He said that the CAT was plugged so i replaced it. I have replaced the coil pack, distro cap, spark plug wires, spark plugs, rotor button, catalytic converter, air intake, and all the air tubes that looked like they were cracking. Now I can start the car, and it does the same thing. I thought it may be out of time, just because that is sort of what its acting like. I have had the motor rev up 3 times since i have had the car. But everytime I do it back fires and DIES, the car will not start til after the car cools down.
View 2 Replies
I've recently rebuilt my toyota celica gt and the engine management light was on , I wiped it and keep getting the same code 52 which I think is the knock sensor car drives terrible under load , idles up and down a little , I've actually replaced the sensor just now and wiped the ecu but as soon as I rev it , bang it's back and I'm getting the same code 52.
View 9 Replies
Ok so i bought a 1994 celica GT from a police auction the other week and it wouldn't start so we went ahead and put a new fuel pump in it then we put new spark plugs in it. When removing the spark plugs i saw there was oil on them. My friend suggest we do a motor swap cause he thinks its a blown head gasket. Could this be an easy fix or should i go through with the swap?
View 5 Replies
It acts like it is fuel poor, As if the fuel pump is not pumping. It spins fast on start. Then another try and it starts! No relationship to hot or cold. Fuel OK. Battery strong. I find no corrosion on fuel pump leads.
View 8 Replies
My 01 Jetta 2.0 started having issues a few days ago. The engine would crank, but wouldn't start. Wait a few minutes and it would start right up. I go to start it the next day and it would crank, but not start at all. I pulled the P0322 code and replaced the crankshaft sensor along with a new fuel pump, and spark plugs just to be safe.
Next, I checked for fuel and spark, which I have both. The car still won't start and seems to lose a charge on the battery pretty quick. At this point, there are no codes showing up. Could the engine be flooded from trying to start it so much?
View 3 Replies
1999 Passat turbo with a little over 100K miles. Car ran fine last night. This morning, the engine/starter cranks well, but no fire. And it has gas in the tank.
View 1 Replies
I started my car a few weeks ago, and the check engine light came on and the S light on my dash kept blinking. Followed by a difficulty stepping on the gas pedal. I attempted the paperclip way of scanning my OBD1 scanner. When I used it, the check engine light went off, no S light blinking anymore, and the gas pedal worked great! I also changed out my VSS (vehicle speed sensor) but the light came on anyway, and my speedometer can't read at correct speeds. Could the engine light problem be because of misfiring due to spark plugs? I don't want to keep buying parts and stuff unless I'm 100% sure it will fix the issue.
View 10 Replies
I run my 92 celica for a good 30 miles and check engine light comes on but after driving another 20-25 miles it turns off. I red the code it was the Egr (code 71) I took off egr valve and cleaned it out idk if its bad, how to test the valve?
View 1 Replies
After removing dpf and egr check engine light is blinking. DPF and EGR were turned off in ECU. I rewrited ECU 4 times with different parameters that was working on other Sonatas.
Still after a while p2002 error comes out and check engine flashes.. few times in day Sonata is starting regeneration (I don't understand how because DPF is turned off).
View 2 Replies
1991 Celica ST 4A-FE automatic, 238,000 miles, son's car, has been running great, until he says his oil light occasionally flickers on him. Car is in Wisconsin, driven maybe 2 miles one way to work every day, hasn't been on the highway is a couple months. Has synthetic 5W-30 oil with about 2,000 miles since last change.
Brought the car into the garage. Sure enough, after engine warmed up and idle got below 1,000 RPM, oil pressure warning lamp would come on. Engine sounded normal at idle and fast idle. Tough to put a mechanical pressure gauge on this engine (after to remove the alternator and A/C compressor and bracket, per the service manual, to access the oil pressure switch). I drove it on the highway, put about 40 miles on it, ran great, until I exited the highway. Anything below 1200 RPM, oil pressure warning light would come on.
Came home, removed the oil filter with intent to change it (to make sure it wasn't plugged). Smelled of gas. Oh-Oh. Drained the oil (oil level was at full mark, unusual for this vehicle, normally would be 1/2-quart low after 2,000 miles - 2 months of winter driving). Oil came out with consistency of water. Smelled of gas, and could see water droplets as I switch the drained oil from a collection pan into a jug. Thought was many short trips caused oil to never get hot enough to burn off unburned fuel blow-up or accumulated moisture, so oil was diluted, much too low viscosity.
Changed oil & filter with synthetic 5W-30 & Purolator PureOne oil filter. Took it back on the highway for 40 miles again. Highway drive was fine. Upon exiting, oil pressure warning light came on at 1,600 RPM or below. Oh-Oh. Had another 40 miles on the highway to get home. Highway drive was good again. Upon existing, oil pressure warning light came on again at 1,800 RPM or lower. Oh-Oh.
Worrying that the oil pump for pressure by-pass valve or of bearing spin-out or extreme wear (although engine sounded fine all the time), decided to order an OEM oil pressure switch. Had to take some of the bolt-ons off to access the oil pressure switch, but not all the service manual said had to come off. Took the old oil pressure switch out - looked just fine. Installed the new one, put everything back together. Checked to make sure the oil pressure warning light still came on with key in the ON position (it did), so I knew the wiring connections were good. Startup was fine (cold engine). Took it on the highway for 40 miles, after exiting highway, no more oil pressure warning light. Even tested the situation with the automatic in drive, brake applied, lights on high-beam, heater fan on high, rear window defroster on (got the engine down to 600 RPM), still not oil pressure warning light. Turned engine off, then turned ignition key to ON, oil pressure warning light comes on like it should.
View 5 Replies
My 96 toyota celica check engine light is on and I get the code P0340. Also I can't seem to get my reverse light to work what could be the problem.
View 7 Replies
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
View 1 Replies
I've got a 1992 Ford Ranger 2.3L with about 240,000 miles on it. The check engine light started blinking on and off pretty regularly so I pulled the OBD1 continuous memory codes and came up with this.
327 - EVP/EPT circuit below minimum voltage
328 - EGR closed valve voltage lower than expected
334 - EGR closed valve voltage high
I can't say these codes mean a whole lot to me besides I've got issues with my EGR valve and possibly the EGR valve position sensor. I was thinking I'd start by replacing the EGR valve.
View 2 Replies
I changed my plugs a few days ago on my 96' Taurus GL 3.0LI checked under my hood to check the recommended gap size and it said .42 to .46.. I went with .46. after putting them in i started the car up just fine, but later in the day i noticed when I came to a stop at a red light my car would sputter and my check engine light would start blinking. When I'd accelerate and drive it again everything would clear up and the light would stop blinking. I didn't change the wires, just the plugs in case you were wondering but I am unsure of how much that would influence my problem. Today after work i had a little trouble starting my car. After a few tries it started and my exhaust smelt rich in gasoline. Did i gap them too much? Should i get new plugs again and regap them? should i buy new wires also?Is my ignition coil going bad?
View 19 Replies
I have an 05 diesel. I have noticed the last 3 days I needed to crank it slightly longer to start it and it takes a second before ideling normally. It usually fires right up and jumps to life. Today i drive about 45 minutes. Stoped for about 30 minutes and shortly after I started it back up the check engine light came on. Will the Ex flash you the codes or do you have to have a reader? Thought I would try Autozone tomorrow but not sure if they read deisel codes or not. I was suspecting maybe glow plugs but who knows at this point. It seems to be running fine and I checked all fluids.
View 13 Replies
My 2002 Windstar SEL has been giving me a fit and I`m not getting any codes as to why. Here`s the 2 main issues. Clicking when i go to start up in a.m. if it`s below 50 degrees. ( Battery has been checked and all is o.k. or so I was informed). As long as it`s warm it starts fine every time. Also,it seems like the least bit of wet on the underside will cause it to spit and sputter and the check engine light will start blinking until it sits and dries for a while. (A very shallow puddle less than 6 inches deep at low speed or even the automatic car wash that sprays the undercarriage).
View 2 Replies
My A/C seems to be not working. Auto mode has fan blowing but only hot air coming out and the A/C light is blinking. Did some searching and performed diag and returned codes 21 & 24. Code 21 due to performing test at night. Have not been able to find reason for code 24.
View 14 Replies
