Celica :: 1990 5SFE Sudden No Start / Just Crank
Mar 11, 2013
Installed a "new" battery in my celica (it was used but tested good) went to start up the car to see if it was good and the car started right up
Shut the car off cleaned up my throttle body a bit the went to start the car again it it would just crank and crank
I just put in a new fuel pump, so that cant be it, I have not checked for spark yet ( car is stuck at work )
I heard that the ignition coil likes to fail on these would that be causing this problem?
View 2 Replies
Advertisement
So I've replaced my head gasket on my 5SFE. But after putting my car back together, my car didn't want start. This is how it sounds like (click on the video to watch it).
So I suspected that my timing was off, so I took off the valve cover to check the timing marks on the camshafts. So the two timing punches lined up like so (I only took picture of one of them)
Though I'm not too sure what the two dots mean on the exhaust camshaft since there are not two similar dots on the intake camshaft.
So I'll assume that I have my camshafts lined up properly But how do I know that it is in time with the pistons?
Could it be the distributor? I am not too sure if I installed it correctly, but I did follow instructions in the Chilton manual.
On the other end, there were two vacuum lines that I'm not sure if I installed correctly. I'm positive that the left two pipes are correct; however, I'm not too sure about the two on the right. This is mounted on the cylinder head.
View 10 Replies
I was driving back home from work and I happen to notice smoke. Oil is coming out of the top of the dipstick hole not the bottom o ring. It seems the crank is building too much pressure . It's a 1990 5sfe so it does not have a pcv valve,ithasa pcv system which is basically a hose from the valve cover to the throttle body.
This does not happen initially when I turn the car on from a cold start. I turn it on leave it at idle for a while and even rev it up and hold it high. It starts to leak after about a 2 mile drive and the car is at running temperature. I removed the hose on the valve cover when the car was at idle and a good amount if air blows out when at idle now when I rev the car up the air blowing out drops some.
View 1 Replies
Once again my Celica is having a similar issue. Originally over 6 months ago i had an issue with my MAP Sensor which was causing extreme hesitation issues and the car was basically not safe to drive in traffic.
The issue that is now occurring is that i can start my car fine and drive around on flat normal roads with no issues but ive noticed once i go up a steep or decent hill/driveway the car will start to bog down around 1500-2100 RPM.
Once it starts to play up it continues to do so even on flat roads.
Have Checked:
- MAP Sensor - OK
- Distributor - OK
- Leads - Old but still ok, plan to replace later.
- Spark Plugs - Ok
- Spark Plug Wells - They had oil in them few weeks ago, cleaned out and hasent returned.
- Need to replace Valve cover gasket to fix this i believe.
- Fuel is ok.
View 6 Replies
My 92 Celica 5SFE 2.2L auto sputters at half throttle. But if I release gas pedal, performance normalizes. I already changed spark plugs cables, ignition coil fuel filter, spark plugs, cleaned injectors, replaced timing belt, engine starts right up and idles a bit high, around 1300 RPM when cold in Park, then when warm 800 RPM in drive. I don't know if it's an electrical issue or a vacuum related issue, spark plugs get carbon fouled after driving like this. I'm tired of having all the newer cars pass me by and my car "running" on 3 pistons.
View 6 Replies
Just finished a timing belt job on my 93 celica 5sfe. Filled the coolant up and burped engine. All seems to be well. My question is related to the coolant overflow tank. The cap has a hose attached on one end coming from the radiator and another coming out the other side that is short and L shaped. The L shaped hose isn't attached to anything and is open allowing air to either vent out or vent in to the overflow tank. There isn't any place nearby where the hose might attach to. Is this hose supposed to be "unattached" as it is now or should it be closed to create vacuum for the overflow tank to allow coolant back in to the radiator?
View 4 Replies
I just got a 1990 toyota celica and it turns over but dont start. its getting fuel up to the motor. i got it from a friend that gave up on it and he got it from a guy that replaced the 2200 with a 2000 engine. everything looks to be connected but i dont know where to start.
View 1 Replies
I have a 1990 Toyota Celica, and I've been having trouble with it not starting after driving. There are no symptoms when the car is running, aside from a very slight rough idle. The car starts fine after sitting for 3-4 hours, but for short trips where it's off for under 1-2 hours, it cranks but will not start. The cranking also seems weak unless I floor the gas while trying to start, and sometimes it will eventually start if I hold the gas while cranking. It always starts at the beginning of the day.
This leads me to believe I'm dealing with a flooded engine, but I'm not sure how to diagnose why. I thought it might be leaky fuel injectors, but wouldn't that cause symptoms when running?
View 7 Replies
I have a 90 celica. I start it up and it idles fast until it warms up. then it runs great until i turn it off. then it will not restart! i went to the gas pump. it would not start after i pumped gas. it turns over but wont start. the next day it starts up fine. it does this all of the time. when it wont start there is no spark coming from the coil except when you let up on the keyl it sparks once.
View 5 Replies
I left my F150 to sit over the winter parked near my house. Battery was bad when I went to start it a few weeks ago. Got a new battery, threw it in, but still no start. It wouldn't crank.
Went to work on it today and the battery was totally dead, took it to schucks and they said it was bad. So I got it replaced with a fresh one and I'm still getting the same thing.
Turn the key on and accessories come on, turn it all the way and nothing happens, except for the aftermarket radio turns off. I replaced the ignition switch last year. I tore apart the dash to see if that went out again but it looks fine.
What should my next step be?
View 1 Replies
1990 Volvo 760 4 cyl. Turbo. Drove the car to work, everything fine. Got off work, car wouldn't start. Cranked but wouldn't start. It was getting spark. Changed the fuel filter, it ran perfect for a month. Drove it to town a month later, shut it off, then trying to start it, would crank and crank eventually start but run real rough. We got it home....barely.
Replaced the fuel filter again. Still wouldn't run right.
Replaced the fuel pressure regulator. Same problem.
Replaced the throttle positioning switch. Same problem. Replaced the air control valve. same problem.
Found out that this car has an on board diagnostic doo hickey.
Found out how to check each sensor and component individually.
All sensors and components are working. Checked both fuel pumps and they are working. If I unplug the air flow sensor and the air control valve sensor, I can start the car using starter fluid and it will idle all day with out missing a lick.If I plug in either one of the sensors, it will kill it immediately.I don’t know what else to do to make this machine run.
View 4 Replies
I have a 90 gts celica, which the motor went in it, so i put a 93 5sfe into it. I took the old distributor out of the 90 5sfe and put it into the new motor. I wasn't getting any spark. So i replaced the distributor with a known good one. No spark. replaced the coil and igniter, no spark still.
View 10 Replies
Just acquired a 1990 celica gt at a steal lol and needing some troubleshooting answers. tonight was the first night we really had drove it, but my husband drove it to work which is an hour away and he noticed that when he comes to a stop the oil pressure light comes on. as soon as he starts to go again it goes off. the engine does not make any noises other than the typical 2200 lifter chatter and it does not leak oil.
We plan on doing an oil change so we are not sure if that could just be the issue or if it's something else. we had this issue with a dodge ram we had and it ended up being the oil pressure sending unit. he took the one off the car and it did need some tightening up but however when he put it back on the issue was still there.
We do not believe it's any low compression as the car cranks fine and normal with no rising of the cranking as you would get for a cylinder with low compression. we aren't really sure about the bearings because well that's not one of those things easily tested but the engine doesn't make a noise which I know at times you won't have one.
View 12 Replies
90 GTS - Manual Transmission. 5SFE
I have a vibration that rattles the cab of the car during start up. But if you get out, lift the hood and listen, you cant hear anything. Its only in the cab where you can even tell there's something not right. The motor runs great and seems very smooth to the touch and visually.
The vibration does seem to go down as the car warms up..... Somewhat....You can hear the vibration when driving and go down through slight dips in the road. Kinda like hitting the rumble strips on the side of the hwy.When I release the clutch and under power the vibrations go away. Under deceleration the vibrations are loud.After weeks of research, both TN and the web, I have done all this so far.
Changed Plugs, wires, cap. All four engine mounts were taken out, inspected, and 3 of the 4 were replaced from a donor car. All 4 looked good anyways....
Swapped harmonic balancer/pully from a donor car.
Compression check. 196 200 200 208
Cleaned IAC valve.
Pulled off exhaust manifold and verified CAT isnt broken.
Inspected exhaust from front to back and cant find anything.
Replace timing belt, tensioner bearing and idler bearing while I was in there.
Took both fan belts off and ran car to see if maybe power steering or AC, but car still rattled even though they weren't turning.
Did head gasket while building this car up because it was leaking oil from the front return tube area.
View 4 Replies
I recently took the engine apart and got the head resurfaced after the head got warped. New thermostat, waterpump, timing belt, serpentine belt, power steering belt, and gaskets for all sorts of stuff. After reassembling the engine everything worked fine. No strange noises. Only problem i am having now is that the cooling fan switches on really late, when the needle is 3/4 of the way towards H, sometimes even a little later. Fan is working as when i disconnect the cooling fan switch(bottom of radiator) and the fan does kick on. ECT was also replaced and nothing seems to work. I did replace the switch and the fans failed to kick on, unfortunately i got it from Autozone.This is a 1990 Celica GTS with the 5SFE 2.2L
View 8 Replies
I have a 1990 GTS with a transplanted 1996 S5HE 2.2 motor. This summer I started getting overheating issues and I believe my water pump is dying.
Here's the symptoms; car will run nice and cool on the freeway doing 70 with the tach turning at 3.5k. As soon as I get off the freeway and RPMs drop the coolant temp will spike almost into the red. Accelerating from the stop will drop the temp but it will hover near the high end of the middle till I get back on the freeway or RPM's go back up.
It does the same thing when climbing hills or when the engine is under load. It did it bad this summer when it was hot out and I was running the AC. Bad enough that it boiled over a couple times. The radiator is brand new and just based on the symptoms I'm thinking water pump.
View 7 Replies
When I put my key in the ignition, I cannot turn the key. I tried putting a small amount of WD40 in the ignition and turning the wheel back and forth while trying to start, but all that did was make my key greasy and my wheel lock up. I've tried getting a new key made from Lowes and Home Depot, but their keys are too wide and will not fit in the keyholes. The only thing I am down to is replacing the ignition switch completely but I'd rather do that as a last resort because my car has had a big problem every week (alternator gone, new wheels, new master cylinder, new rotors/brakes). I haven't explored yet? And also, if it comes down to replacing the ignition switch, how would I do that without being able to turn the key?
View 2 Replies
A little background on how I got into this situation. Bought a '90 Celica GT for $300, was told it had a blown head gasket. It started and sounded nice, if a little ruff. Upon driving, it would stutter (like a misfire) till 3k rpm's, then that would go away and she purred like a kitten. Ok I thought I can make this girl into a woman. I start my teardown and what I found was: front 5 head bolts were not torqued down, and the only place on the old gasket that looked like blowby was on cylinder 3 towards the front on the engine. I think to myself it was loose headbolts, bang I send the head in to get cleaned, buy the gasket kit and go about cleaning the various other parts.
I was cleaning the blocks mating suface, and discovered a small surface crack. It goes from one water jacket port to the headbolt hole and to the other water jacket port.
The headbolt hole shown is the 4th(from timing belt) on the back of the block. The loose headbolts were on the front.
The crack does NOT go down the side of the bolt hole, or the water jacket ports. I am just really afraid this means a new block. The parts I can return if all else fails, but Im down the tube on the money spent on the car and head cleaning.
View 9 Replies
1990 Celica GT ... I will be completely replacing the transmission, and the flywheel while adding a new stage 2 clutch kit. Also replacing the shocks all around.
Okay now to the problem, I don't know exactly where or what fluid or fluids it is yet. it seems to be leaking oil from the oil pan drain bolt also it seems to be leaking coolant too from somewhere behind the oil catch pan area. I did not change the water pump when the timing belt snapped but it looks like some water corrosion on the pump itself. are these common problems and what will solve these leaks?
View 5 Replies
My Celica is running great, I drove about 30 miles and the car started hesitating to run, I was in heavy traffic, I could hear rattling sounds which appeared as though they were coming from the heater. I stopped at a stop light and I could tell something was burning out. I have lots of power, car is very fast. I went to the next stop light and the car died, it started and I went to the next stop light with plenty of speed and the car died and would not start again. I tried starting the car for 3 hours, no fire from the coil.
I have no spark out of the coil. I am confident the coil is good. I have 2 coils. I went to the salvage lot and purchased an "igniter" (ignition module). I installed it on my Celica, still no fire out of the coil. I have a relay under the glove box that clicks when I crank over the engine. The engine cranks over very well for over 3 hours. I have an after market alarm. Why do I not have spark out of my coil?
View 1 Replies
I have a 90 celica gts. when it drove, it would violently shudder taking off in first gear. the front motor mount was shot so i was hoping that was the problem. well right after i fixed it, the starter went so i had to compression start it, and the shuddering was still there, and i was about to shift to second when it revved up popped outta gear and didn't go anywhere. it wouldn't go into any gear.
I can go through all the gears without the clutch in. the guy i got the car from said the clutch was new. now i'm not sure if hes just lying or if the guy who put it in didn't know what he was doing. could this be a bad throughout bearing? or the trans? if its the trans i'm scrapping it, also the shiftier is REALLY loose. and before the clutch went it would make weird whirring noises in 1st.
View 5 Replies
