The first is a trans control system malfunction and the 2nd code(0740) is tcc circuit malfunction- but what exactly do these codes mean? and the o2 sensor needs to be replaced, it said bank 1 sensor 1- does that mean the one BEFORE the catalytic converter?
View 4 RepliesI have a 2005 Grand caravan with a 3.3L. Over the summer I was having issues with the transmission.Got the codes reaf, P0700 and P1726( I think). After this had an input speed sensor replaced and the TCM. The van worked for about 3 months, but now is acting up again. This time I got codes P0700 and P0704. Was told it was a clutch switch malfunction. Can't seem to find any details about this code.
View 1 RepliesMy 98 blazer (130k)recently started showing code p0740 tcc circuit malfunction..
The truck runs fine (except for the water pump I just blew) this is a tranny solenoid code. but my tranny seems to be shifting ok..
Is the solenoid easy and cheap enough to replace myself? I am trying to make up my mind if its time to start thinking of trading this blazer in on something with less miles or to fix it up and keep on trucking..
I'm not too knowledgeable about wiring and electrical systems. I'm getting a P1451 code (EVAP Control System Canister Vent Solenoid Circuit Malfunction) on my 99 4.2. I've read that it could be a bad solenoid, bad wiring, or a blown fuse. So far I've;
- checked (and changed) the related fuse
- checked the wiring for damage at the connector
- checked voltage at the connector (12 volts)
- checked the resistance at the solenoid (around 60 ohms)
- actuated the solenoid with a 9V battery (can hear it opening and closing)
I haven't had a chance to check the wiring all the way back up the frame to yet, but I noticed that the ground at the trailer wiring harness has broken off the frame. Would this potentially cause a fault in the upstream wiring? I'm going to slap a new connector on and bolt it back down anyway, but as it's Labour (Labor) Day I'll have to wait for the stores to be open tomorrow.
I have some codes on my ranger 2000 here goes
P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)
Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?
My problem is similar to that of coyote54 back in 05. I have a 2001 Grand Caravan Sport. Instrument Cluster is dead, Information lights on top of dash are dead, Turn signals and Hazard lamps are not working. Found Hazard Lamp fuse to be blown. Replaced fuse and blows immediately indicating a short. Haynes describes a Turn Signal/Hazard Lamp and Daytime Running Light Module located on the junction block but there is no such animal that I can find. One of the responses to coyote54 described a Hazard relay located within the steering column........again, I do not see anything on the column that resembles a relay. Is there a hazard flasher/relay on the 2001 GC.
View 14 RepliesP0032 Oxygen Sensor Heater Circuit High Voltage (Bank 1, Sensor 1)
I have read that in 2005 chrysler changed the ohms levels for the oxygen sensors and may need to have bcm reflashed to get a new oxygen sensor to work wheither its dealer item or not, is this true if i were to buy a mopar oxygen sensor? aftermarket is out of the question being the ohm readings would require me to spend some time at the dealer. is this code a defective sensor? or could it be related to the thermostat being faulty? am not low on antifreeze and temp gauge reads normal.
My 1996 Caravan gauges do not work at all. I have checked the fuse(s), and thay are all fine.The rest of the van works just fine. The fuel, temp,tach, and speed gauges do not work. The odo does not show up either. What to do?
View 14 RepliesFirst, about a month ago the gas gauge started to malfunction. The low fuel light will come on and the gauge will show low even though it has nearly half a tank left. When will fill it the gauge only goes to 7/8 full.
Second, today is started stalling when I press down on the pedal. If I wait a few minutes it will restart. Has stalled twice but then will run fine.
I'm wondering if there is a 100% way to check and see if my climate control module is bad. No lights work on it, it doesn't turn on the ac or the blower. I took it off it all seems to be decent from what I can tell. But its just not working.
View 1 RepliesMy check engine light has came on and I received these error codes
PO441 : Evaporative emissions control system incorrect purge flow.
PO 455 : Evaporative emissions control system pressure leak-large leak.
PO 446 : Evaporative emissions control system vent control circuit fault.
Also only my driver side fan is working, may be separate issue?
The cruise control quit working on my 2007 Town and Country. The indicator light in the instrument cluster flashes but won't stay on. If I have the ignition switch on but the engine off the light will come on and stay on.
View 4 RepliesI've got a '99 Passat wagon with the 1.8T. My check engine light came on the other day. i had a friend check it w/ his OBD 2 code reader. I got 2 codes: 1300 & 1136. "boost calibration fault" & "fan circuit control malfunction" , respectively. are either of these worthy of a trip to the shop, or can i handle this on my own?
View 3 RepliesIn our 2005 Chrysler Town & Country Touring Minivan, the tire lite on the dashboard came on last night and the following message appeared on the overhead console: "Service Tire System Soon". I filled all the tires to specs, but the light and message remain. The lite on the dash goes out, but the message stays on. Has a tire pressure sensor failed? If so, how does the mechanic know which one? Finally, how much does a tire pressure sensor cost?
View 2 RepliesAfter about 6 months I finally got the alternator replaced in the Tribute. I totally forgot about the CEL that was on for EGR Circuit. I've found a couple of pages ( OBD-II Trouble Code: P0403 Exhaust Gas Recirculation Circuit Malfunction ) that explain how to diagnose the issue but I was wondering if any other route for something that may be more common than another thing.
View 2 RepliesVehicle: 2003 Dodge Grand Caravan 3.3 Litre
I also have my CE light on. Hooked up my reader and got the "P1491 Radiator Fan Control Relay" code. I have checked my rad fan fuse and it is okay. My attempt to locate the rad fan relay took me from the rad fan wire to a device that looks like a heat sink. It is located on the vehicle frame between the rad. and front grill. Is this the rad fan relay? If it is I'm not sure how I would replace it. It seems riveted to the frame.
Started this winter as a misfire on random cylinders. I replaced all apart plugs and verified the gap. Replaced all the coils. Still occurred during the cold months. Once it warmed up it went away for a short while. The only codes present at the time were random misfire codes. Took it to a shop and they told me the injector was bad on cyl 1. Today I replaced the injectors with a matched set of 4 matched flow Denzo remand. Ran it on the TIS tech tool and was given a barrage of codes. I can unplug #1 coil and it will smooth out and stall within 90 seconds. Engine runs rough. Intake was just done as well. From Toyota TIS
P3191 – engine didnt start
P3000 - Battery Control System
P3101 – engine system malfunction
P3190 – poor engine power
P1300 - ignition circuit malfunction #1
P0303
P0302
P0301
P0300
c1259 - ABS error code meaning problem with regenerative braking. Probably caused by me forcing the car to recharge the HV while misfiring. HV battery was getting dangerously low from sitting for the last 6 months.
b0116 – LH airbag circut
I have a 1999 Ford Explorer with the V-6 SOHC that is stuttering and stalling when I try to accelerate. A very slight acceleration will get the vehicle moving, but anything coming close to normal gas pedal pressure causes immediate stuttering and/or stalling. Check Engine light came on when problem started yesterday.
Where is the EVAP System Canister Vent Solenoid? I bought a code reader after beating my head against the truck all afternoon and got code "P1451 EVAP System Canister Vent Solenoid Circuit Malfunction". My Haynes book says on the left side frame rail... can't find anything along there that looks like it (based on picture from Rock Auto for replacement part) and found some people online talking about it being in the engine compartment on the passenger side...
Just crawled all over the truck and I think I found the charcoal canister, but couldn't trace it back to the vent solenoid... There was something right next to the canister, but again, it looked nothing like the replacement part listed on Rock Auto...
C1241 is low voltage warning and C1223 is an ABS control system malfunction.
Are or could these be related? Where should I start to troubleshoot the issue?
I recently acquired a 2003 Dodge Neon and have also aquired a problem with the automatic transmission.The check engine light was on so I read the codes and they are noted below
P0700 Transmission Control System Malfunction
P0755 Shift Solenoid B Malfunction
Based upon some very basic research, I checked into replacing the Transmission Control solenoid.It sounded like this is a pretty common problem for this transmission, so hopefully this would fix the problem.
I was able to get the old one pulled off without to much trouble, but prir to installing the new one I was wondering if there would be a way to test the old one to verify that it was actually bad. I would prefer to not install the new $150 part only to find out that this was not the problem. (and then I could not return it once it had been installed) Maybe some low air pressure on the ports and verify that the ports / flow changes if 12 VDC is applied to the right pins?
A little more information in regards to the "failure" mode. The transmission appears to act the same no matter if it is placed in 1,3 or D. (reverse works fine) I would have expected that it would limit out with the motor taching up pretty high at about 20 MPH in 1(low). It goes down the road fine up to about 55 mph and then the engine starts taching up.
I also tried to reset the error codes with my "craftsman" code reader and it would not do it. I seem to recall seeing something about needing to reset codes before the new solenoid would work. Will pulling the battery for an hour clear the code? Do I need to clear the code?
I have an emissions test coming up. I have 3 P codes that I'd like to eliminate before then. I don't want to "fix" the issues they are telling me about. Just make the codes go away. I know why they're there I just need to get rid of them.
What I have coming up is:
P0475 Exhaust Pressure Circuit Valve (result of EBPV delete)
P0541 Intake air heater A circuit low (result of aih delete)
P0640 Intake air heater control circuit (also result of aih delete)
What resistors I'll need and where to put them in?