When I start my van first thing in the morning it starts fine when it reaches t2he normal operating temp on my gauges, it begins to stall and dies. Then after Restarting it once or twice it runs great the rest of the day.
View 1 Replies1st problem is shifting from 1st to 2nd and sometimes from 2nd to 3rd though, 2nd to 3rd is not as bad as from 1st to 2nd. It stumbles and gets really bad if I don't let up on the gas. After the initial shudder it will go into 2nd just fine. I also have to gun the gas a little bit when I first start the car, or it will just sit there and idle and never go into gear.
2nd and more annoying is that it stalls after driving around a bit. It happens on freeway or city. It doesn't stutter or anything the rpm's drop to 0 and it just stalls and won't start up for a 5 - 10 minutes or so.
Codes pulled are P0731, & P0736. The transmission was replaced about 2 years ago with a refurbished one. Could it be going out again already? The guy at Autozone suggested replacing the TSS (Transmission Speed Sensor?) to see if that was the problem. I have not done this yet, but plan to.
I have a Suzuki Esteem on which I have recently had following work done from a suzuki dealer on their recommendation.
1) Throttle body repair and Cleaning.
2) Idle air control valve cleaning.
3) New fuel filter, air filter, spark plugs.
4) Engine tuning.
5) New battery.
6) New power steering belt.
PROBLEM: (Only when AC is OFF)
When my car reaches operating temperature the engine stalls out after three seconds at idle.
Suzuki dealer does not seem to know the reason behind this and they want to keep it for a few more days however i think they will just keep replacing parts one after another.
95 ford f250 with 5.8l. I have currently replaced the battery, alternator, distributor, cap, rotor, icm, coil, plugs, wires, act sensor, ect sensor, fuel pump, fuel press regulator. I got it to start today by messing with timing at distributor it ran to operating temp and died. Would crank but not start.. So I replaced the act tensor today.. Now it still won't start... koeo test gives code 327... I am stumped and about to tow it away...
View 11 RepliesI have an 02' Dodge Grand Caravan 3.3L V6 (not flex fuel) .I have replaced the battery, alternator, sparkplugs/wires, fuel pump, fuel filter. All over time and now when i try to start the van it turns over strong sometimes starting then stalls out immediately. When I try to crank it sounds like metal on metal. Check engine light stays on,but i dont have an OBD reader.
View 7 RepliesI have a 2004 Grand Prix and it is displaying the symptoms of overheating but the temp gauge is not going above normal operating temp. I replaced the thermostat twice, and after driving for about 10-20 mins coolant comes out of the overflow. I'm at a loss, I'm thinking temp sensor(?) But I don't want to keep throwing unnecessary money into it. The fans work fine, the heater blows as it should.
View 8 RepliesHow long would you say the engine reaches the full/normal operating temperature?
I have tandem parking at my place and in the morning my GF leaves for work before I do. So I drive at least about a mile before I shut off the engine to make sure everything is warmed up.
I don't have my manual handy, wondering what the normal operating temp of the coolant is for a 1.8T B5? I believe it is 190, but want confirmation.
View 1 RepliesSo I have a '98 cavalier with the 2.2l and 4sp auto. Anyway, it runs great when dry conditions, but when its wet from rain or any moisture it runs terrible. It stalls and stumbles and the cab fills with a gas odor. I changed the coil packs and plugs and wires and it still does it. I have a P0301 cylinder 1 misfire detected and a P0200 injector circuit problem. I'm having a hard time believing this because it runs fine most of the time. Is there something else I can look at that is feeding this problem? Is this a common ocurrance?
View 4 Replies2003 Pontiac Montana 3.4 L
225000 Kms
Intake Gasket replaced already at 60,000 kms (yes a while ago)
Recently, noticed a major external coolant leak at the front of the motor (passenger side). It only leaks when at operating temperature and under pressure. It does not leak when you first start the engine, it takes a while before it leaks.
I replaced the rad cap, just in case it was faulty. Upon the second test, after getting it running good and hot, it leaked again. But only when at operating temp. It is not overheating.
Problem is, as the coolant is leaking out, the main drive belt is splashing the coolant all over the place and thus I am having a heck of a time pinpointing if it is a head gasket or intake manifold leak or perhaps somewhere else.
I can't take things apart to get a better view, because it needs to be running at operating temp to get the leak. If I pull anything apart for a better view, I won't be able to start the engine to reproduce the leak.
'92 Camry 5S-FE 4cyl 2.2L A/T; This one has me puzzled. Runs well, newer ignition parts, but does not start when warmed up to OpTemp. Starts fine cold, restarts when warm after 5-10 minute cool down (is not overheating). Will start hot if starting fluid is injected into throttle body, so problem is unlikely spark, it has to be fuel, right? Just ran SeaFoam thru top end as I was advised it could have been carbon build up, but that did not fix. Got some carbon burn off, but hot start issue remained.
Could it be fuel pressure regulator? Fuel pump and filter both replaced less than a year ago. I have basic tools, but not much more than a Multimeter for test equipment.
2006 Passat 2.0t. With the engine cold, the a/c will blow warm until the engine gets up to operating temp and the rad fan kicks on. After that, it will stay on and blow cold all day. I would think the rad fan should kick on as soon as I turn on the a/c to get air flow moving across the condenser as in every other car I have ever owned.
Does rad fan kick on as soon as you turn on the a/c? I'm thinking that i might have a problem with a relay that suppose to kick the rad fan on. I used my VAG.com software and its showing no faults.
We just purchased a 2012 Grand Caravan and was wondering where to get a key and program it. I know the key will be an arm and a leg if i get it from the dealer. Is there a tutorial that tells how to program it as well?
View 3 Replies2006 Caravan. Heat comes and goes every minute or so. Also noticed the temp gauge goes from normal operating range to cold and back again frequently. Hasn't overheated. Does that sound like a thermostat problem?
View 2 RepliesOn my 2005 3.3L Grand Caravan the ABS light keeping coming on. I inspected the sensors for the front and used my compressor to give them a quick puff of air to get rid of dust. The light went off for about 5 days. Now it is back on.
How does one read ABS codes? If I knew for sure that the problem is a speed sensor and which one I could clean or replace the faulty sensor.
If I clean to sensor are there any special precautions I need to take? As far as I could see they didn't look very dirty.
Having issues with 00 lincoln ls not reaching normal operating temp.
View 1 RepliesCold start ok . Problem arises after engine is at operating temp. After stopping for whatever and attempting to restart, dash no longer lights up with key in on position but starter cranks and engine won't start. Leave key in on position for about a min.dash lights back up and engine starts.
View 6 Replies I own a 2012 GTI. For about the last week the cat needs to be driven for about 8 miles before reaching operating temperature (190). If I make a stop before the gauge has reached 190, the car will cool of very quickly. I realize it is very cold outside but this car and previous GTIs have not had this problem. The heater will not produce heat for the first 4 miles or so which is also not normal. The car has 17,000 miles and is parked in a heated garage every night, fwiw.
Maybe the water pump or something else in the HVAC system?
I have a 1994 Buick LeSabre Limited with a 3800 engine.When the engines cold,it starts fine and drives fine.When it reaches operating temp,if you shut it off. It will crank but not start back up until its cold again. I've replaced the crank and cam sensors but no change.
View 2 RepliesWhat am i missing i have a terrible clunk in the front end when i hit bumps. I thought it was the struts and mounting plates so they are new . no change Stabilizer links were tight but i replaced them as well. Everything else seems tight but the noise has not changed with any of the above mentioned repairs.
View 13 RepliesI'm having trouble with my 96' 3.0L, its kind of crazy its intermittent and while driving the engines surges one or twice and then dies... when I try to crank it up again cranks but don't starts if I try again it wont even crank ( no starter winding up ) what I noticed is that is I'm driving when it dies my check engine light disappears for a while and if I connect my OBD 2 reader does not link up with the ECU if I wait a while and I crank it up again its starts and the while cranking up I can hear a bang noise from the engine compartment drives side and then after a couple of minutes dies again...
View 4 Replies