this has been an outstanding van, quite reliable. it has about 115,000 miles on it. Recently, I've noticed that the transmission makes a 'tapping' noise when it shifts or downshifts. every gear has that same slight 'tap'. the tranny shifts fine, smooth, but this sound worries me a bit. any chance this could be a u-joint issue?
View 1 RepliesI have a 2008 GC 6 speed transmission that has 55000 miles on it. When the engine and tranny is cold the transmission shifts very hard until it warms up. There are times when shifting from reverse to drive it shifts very hard. Also, the siding doors creak when driving over rough roads. Can they be adjusted?
View 2 RepliesSince there is not dipstick for a 2008 GC with six speed transmission, how much transmission fluid goes back?
View 2 Replies2001 T&C with 3.3, 4speed tranny and 128K miles.
Here's an interesting one: This morning I went went to get gas and no problems getting to the gas station. I pull out of the gas station and get to the first light, again no problem. Light turns green, I go and the tranny shifts from 1st to..... nothing! Just like I slipped it into neutral. I coasted into a parking lot, moved the gear selector from Park to R to D to L, and nothing.
I put it in Park and shut off the engine, then restart and shift into drive and it goes into gear! I start to drive away and when it's time to shift, it goes from 1st to.... nothing again! Once again none of the gears work, until I shut the engine off and restart.
After I restarted the engine I shifted to L and drove home in 1st gear keeping an eye on the tach so I wouldn't exceed 3500 RPM. Got home with no problem.
So, to recap, when it goes to shift up from 1st it goes into nothing. Just like neutral. No check engine light, not "limp mode". If I shut off the engine and restart, it'll go into 1st, and if I keep it in L so it won't try to shift up, it'll drive all the way home in 1st. Reverse doesn't work no matter what I try.
Some background: I changed the tranny fluid and filter 2 years ago at around 90K. fluid level is good. It did rain hard last night, conicidence? The engine compartment is dry.
I think it is safe to rule out a mechanical problem, this seems to be electrical and we can probably rule out the tranny range sensor since it keeps it in 1st when I have it in L and the backup lights come on when I put it in R.
Have a 06 Grand Caravan 3.8L that suddenly quit and would start back up easily enough, but one had to keep foot on the gas to keep it going.
I pulled two codes:
P0123-throttle postion sensor 1 high
P0508-IAC valve sensor circuit low/undercurrent
So far I have removed the IAC and cleaned it with throttle body cleaner, cleaned throttle body out as well with the spray, installed new EGR since it got mangled trying to remove it for cleaning. Removed the TPS connector and with key on, took measurements and I am getting a reference voltage proper ( almost 5 volts). I then back probed the connector once it was plugged back in and again things checked out, the reference lead was varying between .7 and 4.7 volts as I manually moved the throttle plate.
I had switched out the IAC with a used one, from an engine that had been running before being parked, but it made no change.
Note: I have a new TPS but am holding off on changing it until I investigate whether or not it may have a clogged fuel filter causing it to stall at idle speed. Now if can just locate where it is..the sketchy diagrams in my Alldata program are useful.
I did a tune up on my 3.3L Dodge Grand Caravan only to find the engine is vibrating heavily. This tune up included a new coil pack, plugs and wires.
I did happen to notice a separate thing when looking at the Crankshaft Pulley that it seemed to be wobbling while the engine was running.
Drivers side not bowing hot air? We changed the blower motor and the resister on the passenger side. We hadn't tried to use the heat until last night when we needed the defrost and that's when we realized only heat on passenger side.
View 1 RepliesI had a VERY bad leak, to the point where I would fill it, an hour later it all leaked out. I had a mechanic work on it, and he rebuilt the PS pump, BUT the pulley was cracked, they DON'T make that size anymore. He put a bigger one on, only to find out, it was rubbing on my brake lines so I couldn't drive it! SO I had another grease monkey work on it, went through a few new pulley's FINALLY found one! BUT went through 4 Serpentine belts!!
After 3 months with NO VEHICLE, we finally got it all back together. BUT now it is not all lining up we couldn't tell until we had the belt on. it is about a 1/4 of an inch to much to the right.
I'm thinking maybe washers or spacers would work?
I have a 1993 Dodge Grand Caravan. I found a small leak in my fuel rail. Can I buy a repair kit for this or do I need to find a new fuel rail? If so where to find a rail for a van this old?
View 2 RepliesMy beloved Treg is marooned at the dealer again, having been towed there this morning. Transmission is all over the place...shifts into 5th and stays there, or extremely jerky shifts - especially downshifts. Gear position indicator is highlighted in red and no longer indicates which gear I'm in. Check engine light is on; no message in MFI...
Incidentally, it appears that the dealer and/or VWOA is starting to understand how to treat luxury vehicle buyers. Roadside assistance was very responsive and courteous. Dealer set me up with a rental from Budget...made a point to have me pick something similar to the Treg (not a POS econobox). I'm driving a Ford Exploder...a far cry from the Treg, but at least it's an SUV and has similar seating and hauling capacity.
My van has quit me finally. It only has 98,000 original miles on it. Right now the car really smells like it is loading up and not properly burning fuel. Also a huge amount of white smoke is coming from the exhaust pipe. The oil pressure is good. could it be as simple as new plugs and plug wires, coil pack etc.
View 3 RepliesMy transmission is slipping when the engine is cold. Fluid levels seem fine. I do have a fluid leak that I monitor and add fluid when needed. It's an 05 touring with 167k miles.
View 1 RepliesI have a 91 Grand voyager and it seems to be loosing transmission fluid somewhere but no puddles anywhere.It looses between 3/4 and 1 quart a month an shifts fine. Where could this be escaping at as I drive it? What do I need to look at since its not dripping anywhere an I snugged the pan an didn't see it there?
View 3 RepliesI have a 1995 Plymouth Voyager se about a year ago the transmission started acting up, for no reason, it would just go it to First and never come out I would stop turn it off turn it back on again and it would be fine..then days later it would go by, it would do it again. it did this for a while and the good days would turn in to a mile or two then it just decided not to come out of first ever, during this, i took it to a trany shop and rebuilt the transmission it worked for a bout a half hour.
Final a mechanic friend checked the computer again and changed it out with another and it fixed it beautifully!!! ok well about a week ago a very odd loud obnoxious squeal started that sounded like a bottle rocket but not all the time, more often than not though. Before I got a chance to take it to my mechanic friend i was driving along and the transmission slipped in to first and wont that's it. i have been doing emergency trips in first gear and also the horrid squeal is gone. the thing have to be linked what should I try and i don't think its the computer, I really don't want to lose my van
I just replaced the transmission in my 2000 3.3L Grand Voyager and now it won't start. It started fine when I drove it into the shop. The battery is good, the cables are ok. The starter worked good up to this point. I checked all the connections to make sure they are tight. I replaced the transmission because reverse went out.
When I turn on the key, the shift letters (PND32) appear on the instrument panel, but the little circle that shows what gear it is in does not appear. When you turn the key to the run position, the circle should be around the P to show it is in park.
When I turn the key to start, nothing happens. No clicks or anything. The next thing I am going to do is see if there is power to the starter when the key is in the start position. Where to start looking?
i have a 2000 grand am with a 3400 engine and stock trans, i did a full engine swap in the car a few months ago for a friend and it was running fine, the engine and trans came out of an 04 grand am. I bought the car for a second vehicle for my every day driver after he changed the (tfp) sensor, and it shifts fine, but it is still showing a P1810 code, and shifts hard after driving it for a while but only when putting it in gear. What it can be?
View 1 RepliesI have a 2002 Town and Country LX with the 3.3L V6. Recently the check engine light went on and later the transmission stopped shifting from 3rd to 4th gear. All the gears work properly except for 4th. It doesn't seem like anything is wrong with the transmission, would this be a sensor problem? If so which sensor would need to be replaced?
View 14 RepliesI am experiencing a very frustrating shift anomaly. 2003 T and C . Under certain throttle conditions ( usually light ) from a dead start I am feeling a bump/violent shudder between the 1-2 transmission shift. If I let off the gas, I can get the shudder to quit and then by continuing to accelerate , successfully complete the 1-2 shift.
Does not happen all the time and never under straight ahead med-hard acceleration. By nature , happens most of the time under light acceleration when turning a corner from a dead stop. Sort of feels like a loss of traction or something funky happening with the torque convertor. Have serviced the trans with new fluid and filter, new TPS, new plugs, wires, and coil pack.
I have a problem with our 97 Grand Caravan, (3.3L, 41TE tranny) Its a vibration that seems to be coming from the passenger side CV Axle.... the transmission side of the universal joint on the new axle.
We started having problems with this in December, I've done most of the work myself but still had the problem... Vibrations that seem to start and get worse at around 35 - 55 MPH. I've replaced rims, wheel bearings, both cv axles, tires, brake pads & rotors, sway bar links and bushings, tie rod ends, (inner & outer) and ball joints. (about $1,200. in new parts & tires)
In April, I finally took it to several transmission shops and talked to the operators.... The shop I chose because I could relate to the owner and felt I could trust him. The wife and I knew it was a vehicle we couldn't replace for the price of a transmission overhaul and when the shop called and told me all was fixed by replacing the new cv axle on the passenger side I was ecstatic that the problem would be fixed.... I go ahead and rebuild the transmission anyway, (now @ 289,000 miles!) .... The wife and I want to get as many miles out of this thing as we can at this point and our daughter will be driving it to high school next year.
Anyway, I get the car back late on a friday evening.... by the time I got it home I knew there was a big problem.... I put it up on jacks in the garage and saw the passenger side axle was "Slamming" in and out of the transmission!!! I test drove it on a few more short trips and took it back a week later.
About 1 1/2 weeks later I get a call and the shop owner says it is the CV axle thats bad.... AGAIIN??? Lets see, I replaced the original axles. Then "they" replaced both axles after I returned the ones I put in for warranty (Autozone) and now a 3rd axle is bad too? He insists on a different brand of axle (Napa). So when I get the car back, I again am feeling some vibrations.... not nearly as bad as it was before, and put the car up on jacks again.
This time, I don't see the axle slamming in and out of the tranny but I see the vibration comming from the trany side of the CV axle. (passenger side axle again) and I notice some grey goop on the housing fitting that wasn't there before on the trany.... This is when I started having my doubts about the shop and what they are telling me. They just replaced the axle, didn't do anything in the tranny. To beat all, theres now a fluid leak somewhere and its staining the garage floor.
Its been over two weeks now and the shop owner called me to tell me that its again the passenger side axle thats bad and that its a seal somewhere tha'ts leaking so he's gonna have to pull the tranny to get at it. I told him what I saw when I put it up on jacks in my garage.... the vibrating CV axle on the passenger side of the tranny.... He assures me that if it were a bearing it would be making some noises. He's even sent the car to a trusted tire shop and they turned the rim on the tire or something.... he's doing everything he can to make sure the problem is taken care of.
I know what I saw under the car. Just the "passenger side" axle as it is coming out of the transmission housing is moving up/down/around and that's where my vibration is coming from. The end of the axles (tire side) were running true. What's involved in repairing the differential side bearings in these tranny's? I'm going fully loaded to the Transmission shop when its ready and I'm going to insist we look at it while its on the rack. I just need to know how to check these differential side bearings.
So here I am with my 1996 Dodge grand caravan that I purchased new in 1995 for a whopping 30k. Yeah hind site is 20/20 skip forward to mile 102k transmission fails completely. Had to have it towed in to shop, rebuilt tranny put in... skip ahead another 4 years to mile 173k and transmission fails again. Again on a tow truck to the shop and ANOTHER tranny rebuild. So now I am at mile 182k and transmission is making a horrible shudder and I have moved across the country away from original shop that did last trans repair (who says they only warranty if I come back to them) and I am possibly looking at another repair or replacement. What is the deal with these vans?
View 4 RepliesI installed the TurboKits CAI kit a few weeks ago. Installation went smoothly, and the latest kit has a modification to the box that fits our Accent's air snorkel. On cars with automatic transmissions, I had to cut out a notch from the bottom of the box to clear the transmission, but I doubt that this affects the air flow to the filter.
However, I have a big problem with the sound. The transmission often shifts at very low RPMs, and the CAI makes a very loud burble when this occurs. If I shift into a lower gear using the semi-manual mode, then the sound goes away. I realize that CAIs make a louder sound when you put your foot into it, but I find the sound a little over-the-top (especially considering that when the sound comes on, the engine is producing very little power at this part of the power band).
So, it's not really a problem with the CAI itself, more with the car's TCU. Unfortunately, it's too annoying for me, so I'll be reverting back to the original air intake system, and selling the TurboKits CAI.